Equinox Systems FEVER User manual

FEVER
order code: EQLED42
user manual
www.prolight.co.uk

WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
Equinox Fever Safety

Equinox Fever Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.

You should nd inside the Equinox carton the following items:
1, Equinox Fever 2, Power cable 3, Instruction manual
Technical Specications:
DMX channels: 4
Voltage: AC 110-240V ~ 50Hz/60Hz
224 Ultra bright LED’s (R: 48, G: 48, B: 48, W: 48, Y: 32)
Fuse: 1 Amp
Power Consumption: 25W
Dimensions: 330 x 230 x 230mm
Weight: 2.5Kg
Operations:
There are 3 operating modes to choose from:
1, DMX Mode 2, Auto Run 3, Sound Active mode
DMX Mode
When the unit is connected with a universal DMX controller, press the “MODE” button to show
“Addr” in the LED display window, you can now set the DMX address from 001-512 using the
“UP” and “DOWN” buttons, once you have set your desired DMX address press the “SET UP”
button to conrm the setting.
Auto Run Function Mode
When the unit is not being used via a DMX controller, press the “MODE” button to show “Func”
in the LED display window. Now press the “SET UP” button and select one of the three following
operation modes using the “UP” and “DOWN” buttons:
1) “Soun” = Sound Active mode
2) “Slav” = Slave mode
3) “Auto” = Auto Run mode
Once you have selected your desired operation mode press the “SET UP” button to conrm
the setting.
Sound Active Mode
To activate the Sound Active mode, rst please make sure that you selected “Soun” in the LED
Display window from the above Auto Run Function Mode. Now press the “SET UP” button and
select one of the 15 different ower effects using the “UP” and “DOWN” buttons.
“P-00” = Runs all 15 ower effects one after another
“P-01”>> “P-15” = Runs selected individual ower effects
Once you have set your desired ower effect press the “SET UP” button to conrm the setting.
To adjust the sound sensitivity in Sound Active mode press the “MODE” button to show “Sens”
in the LED display window, then press the “SET UP” button and adjust the sensitivity using the
“UP” and “DOWN” buttons. Once you have selected your desired sensitivity level, press the
“SET UP” button to conrm your setting. (“S-00” = Low, “S-15” = High)
Equinox Fever Technical specications

Other functions
Slave Mode
To set the unit in the Slave mode, press the “MODE” button to show “Func” in the LED display
window. Now press the “SET UP” button and use the “UP” and “DOWN” buttons to show “Slav”
in the LED display window and press the “SET UP” buton to conrm the setting.
The unit will now run in conjunction with the Master unit when linked together with multiple units.
LED Display On/Off
Press the “MODE” button to show “LED” in the LED display window and press the “SET UP”
button to choose one of the two following options using the “UP” and “DOWN” buttons.
1) “ON” = The LED display will stay ON all of the time
2) “OFF” = The LED dispaly will turn OFF after the setting has been conrmed
Once you have selected your desired option, press the “SET UP” button to conrm your setting
Blackout Mode
Press the “MODE” button to show “Blnd” in the LED display window and press the “SET UP”
button to choose one of the two following options using the “UP” and “DOWN” buttons.
1) “NO” = Auto run mode when the unit is not in Sound Active
2) “YES” = Blackout mode when the unit is not in Sound Active
Once you have selected your desired option, press the “SET UP” button to conrm your setting
DMX Function Chart
Equinox Fever Functions
Function
Blackout Mode
Static colour mode
(Use CH2 to select any of the
24 static patterns/colours)
Sound Active Mode
(Use CH2 to select any of the
30 built-in dynamic patterns
triggered via the internal
microphone)
Channel 1
000-009
000-009
010-255
Channel 2
000-009
010-255
000-255
Channel 3
N/A
Strobe Speed
Strobe Speed
Channel 4
N/A
Master Dimmer
Master Dimmer

Further DMX cables can be purchased
from all good sound and lighting suppliers
or Prolight dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent xtures and controllers. A DMX controller sends DMX data instructions form the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have
a data “out” terminal).
DATA Cable (DMX cable) requirements (for DMX operation):
• The Equinox Fever can be controlled via DMX-512 protocol. The DMX address is set on the
back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for
data input/output (gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Equinox Fever DMX Set up

Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic
behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Equinox Fever DMX Set up

www.prolight.co.uk