Equinox Systems Viper User manual

Viper
User Manual
Order code: EQLED375

www.prolight.co.uk Viper User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modications to this equipment are not subject to warranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and
the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage
connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when
equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available mains supply voltage is
between 100~240V AC, 50/60Hz.
• Make sure that the power cable is never crimped or
damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualied
engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic
temperature uctuation (e.g. after transportation),
do not connect power or switch it on immediately.
The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the
original packing material), and return it to your Pro Light
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be
carried out by a qualied technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• Warning! Risk Group 2 LED product according to
EN 62471. Do not view the light output with optical
instruments or any device that may concentrate the beam.
• WARRANTY: One year from date of purchase.

www.prolight.co.uk Viper User Manual 3
Product overview & technical specications
The Viper projects a wide array of multicoloured beams of light that rotate and twist around the room. 12 white
SMD LEDs sit in 2 horizontal strips on the front of the unit adding a strobe effect for an extra dimension. Control
is facilitated via 2 rotary knobs on the rear, one to select the auto or sound modes and the other for adjusting the
speed/sensitivity settings.
• 3 x 3W tri-colour LEDs (RGB)
• 12 x white 5050 SMD LEDs
• Auto and sound active modes
• Supplied with hanging bracket
• 2 rotary knobs for mode/setting adjustment
• IEC power input
• Convection cooled
Viper
Specications
Power consumption 18W
Power supply 100-240V, 50/60Hz
Fuse F1A 250V
Dimensions 160 x 167 x 177mm
Weight 1kg
Order code EQLED375
25mm
154mm
177mm
137mm
167mm
104mm 56mm
160mm

www.prolight.co.uk Viper User Manual 4
Operating instructions & WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed of
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.
01 - Mode selection
rotary knob
02 - Speed/sensitivity
rotary knob
03 - IEC power input
04 - Fuse F1A 250V
05 - Microphone
06 - Earth point
07 - Hanging bracket
08 - Hanging bracket
adjustment knob
09 - Safety eye
In the box: 1 x xture,
1 x power cable
& 1 x user manual
MODE
MIC
SAFETY
EYE
SPEED/
SENSITIVITY
Auto 1
Auto 2
Auto 3 Sound 1
Sound 3
Sound 2
POWER INPUT:
100-240V~50/60Hz
FUSE: F1A 250V
POWER
CONSUMPTION:
18W
www.prolight.co.uk
IPER
01
06
08 08
07
03
04
02 05 09
Operation:
Connect the xture to a suitable mains outlet using the IEC power input on the rear of the xture.
Use the mode selection rotary knob to choose one of the 3 auto or 3 sound modes, then use the
speed/sensitivity rotary knob to select the auto program speed/sound sensitivity.