Equinox Systems Fusion Razor Beam EQLED006 User manual

Order code: EQLED006
Fusion Razor Beam
3 x 12W Moving Head
User Manual

www.prolight.co.uk Fusion Razor Beam User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablevoltageisbetween
100~240V,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• WARRANTY:Oneyearfromdateofpurchase.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!

www.prolight.co.uk Fusion Razor Beam User Manual
3
Product overview & technical specications
TheEquinoxFusionRazorBeamutilises3x12WquadcolourLEDstoproduceintenserazorsharpbeams.
Thecompactandlightweightdesignallowsforeasytransportationandinstallation.The4pushbuttonLED
menuallowsforeasyaccesstothefunctionsincludingDMX,auto,soundactive,strobeandmaster/slave
modes.LoadedwithadvancedinternalprogrammingbyEquinoxthesoundactiveandautomodesdeliver
stunninglightshows.
•3x12Wquad-colourLEDs
•Beamangle:8°
•Pan:540°,Tilt:180°
•DMXchannels:1,4,7or10selectable
•Auto,soundactive,strobeandmasterslavemodes
•0-100%dimmingwithvariablestrobe
•4pushbuttonmenuwithLEDdisplay
•IECin/outsockets
•3-pinXLRin/outsocket
•Fancooled
•Suppliedwithhangingbracket
Fusion Razor Beam
Specications Razor Beam
Powerconsumption 89W
Powersupply 100~240V,50/60Hz
Dimensions 288x222x190mm
Weight 3.6kg
Ordercode EQLED006
0m 1m 2m 3m 4m 5m
8° - Lux 1700 700 300
8°
170 70
222mm
288mm
190mm

www.prolight.co.uk Fusion Razor Beam User Manual
4
Technical specications
01-LEDdisplay
02-Menubutton
03-Downbutton
04-Upbutton
05-Enterbutton
06-Poweroutsocket
07-Powerinsocket
08-Fuse5A250V
09-DMXin
10-On/offswitch
11-DMXout
Inthebox:1 x xture,
1 x power cable,
hanging bracket &
1 x user manual
DMX OUTDMX IN
ONOFF
POWER IN/OUT
01 09 100802 04
03 05
11
06
07
MENU DOWN UP ENTER

www.prolight.co.uk Fusion Razor Beam User Manual
5
Operating instructions
DMX channel selection:
OperatinginDMXcontrolmodegivestheuserthegreatestexibilitywhenitcomestocustomisingor
creatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthextureandeach
xtureindependently.
ToaccesstheDMXchannelmode,pressthe“MODE”buttononthefontoftheunittoshowCHnd
ontheLEDdisplay.Nowpressthe“ENTER”buttonandthechannelmodewillbedisplayed.
Usethe“UP”and“DOWN”buttonstochooseoneofthe1,4,7,or10DMXchannelmodes.Pressthe
“ENTER” buttonagain,thiswillsettheDMXchannel.ThedisplaywillnowdisplayAddr.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Channel Value Function
10-7 Blackout
8-127 Autorun(AT01)
128-255 Soundactive(128:lowsensitivity,255:highsensitivity)
1 channel mode:

www.prolight.co.uk Fusion Razor Beam User Manual
6
Channel Value Function
10-255 Panadjustment
20-255 Tiltadjustment
30-255 0-100%dimming(0:lowbrightness,255:highbrightness)
40-4 Blackout
5-14 Red
15-24 Green
25-34 Blue
35-44 White
45-54 Cyan
55-64 Yellow
65-74 Orange
75-84 Pink
85-94 Purple
95-104 Pastlegreen(green&white)
105-114 Pastlered(red&white)
115-124 Pastleblue(blue&white)
125-134 Pastlepink(red,blue&white)
135-144 Warmwhite(orange&white)
145-150 Blackout
151-200 Colourfade(151:slowfade,200:fastfade)
201-255 Colourchange(201:slowchange,255:fastchange)
Channel Value Function
10-255 Panadjustment
20-255 Tiltadjustment
30-255 0-100%dimming(0:lowbrightness,255:highbrightness)
40-255 Red(0:lowbrightness,255:highbrightness)
50-255 Green(0:lowbrightness,255:highbrightness)
60-255 Blue(0:lowbrightness,255:highbrightness)
70-255 White(0:lowbrightness,255:highbrightness)
4 channel mode:
7 channel mode:

www.prolight.co.uk Fusion Razor Beam User Manual
7
Operating instructions
Channel Value Function
10-255 Panadjustment
20-255 Tiltadjustment
30-255 Speed(pan&tilt)
40-255 0-100%dimming(0:lowbrightness,255:highbrightness)
50-255 Red(0:lowbrightness,255:highbrightness)
60-255 Green(0:lowbrightness,255:highbrightness)
70-255 Blue(0:lowbrightness,255:highbrightness)
80-255 White(0:lowbrightness,255:highbrightness)
9 0-4 Blackout
5-14 Red
15-24 Green
25-34 Blue
35-44 White
45-54 Cyan
55-64 Yellow
65-74 Orange
75-84 Pink
85-94 Purple
95-104 Pastlegreen(green&white)
105-144 Pastlered(red&white)
115-124 Pastleblue(blue&white)
125-134 Pastlepink(red,plue&white)
135-144 Warmwhite(orange&white)
145-150 Blackout
151-200 Colourfade(151:slowfade,200:fastfade)
201-255 Colourchange(201:slowchange,255:fastchange)
10 0-127 SoundcontrolviacontrollerisOFF
128-255 SoundcontrolviacontrollerisON
10 channel mode:

www.prolight.co.uk Fusion Razor Beam User Manual
8
Changing the address:
Toaccesstheaddressmenu,pressthe“MODE”buttononthefrontoftheunittoshowAddr
isdisplayed.Pressthe“ENTER”button,theunitshouldnowdisplayA001.Usethe“UP”and“DOWN”
buttonstoselectA001throughA512.Pressthe“ENTER” buttonagain,thiswillsettheaddress.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Slave mode:
Toaccessslavemodepress“MODE”untilthedisplayshowsSLnd.Pressthe“ENTER”button,theunit
shouldnowdisplaySL 1.Usethe“UP”and“DOWN”buttonstoselecteitherSL 1orSL 2.Press
the“ENTER” buttonagain,thiswillenableyourchosenslavemode.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Adjusting the sound sensitivity:
Toaccessthesoundsensitivitymenupress“MODE”untilthedisplayshowsSoUn.Pressthe“ENTER”
button,theunitshouldnowdisplaythesensitivityinthreedigits.Usethe“UP”and“DOWN”buttonsto
select001through100.Pressthe“ENTER” buttonagain,thiswillsetthesoundsensitivity.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Auto mode:
Toaccessautomodepress“MODE”untilthedisplayshowsAuto.Pressthe“ENTER”button.Theunit
willnowdisplay At01.Usethe“UP”and“DOWN”buttonstoselecteitherAt01orSou1.Pressthe
“ENTER” buttonagain,thiswillenableyourchosenautomode.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Other settings:
Operating instructions
PAn (Xmotorpositive/negativemoveset) YES/NO
tilt (Ymotorpositive/invertmoveset) YES/NO
Led (digitaldisplayON/OFFset) ON/OFF
diSp (digitaldisplayinvert) YES/NO
test (functiontest)
HoUr (totalxtureruntime)
rSEt (reset)

www.prolight.co.uk Fusion Razor Beam User Manual
9
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Note: DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk Fusion Razor Beam User Manual
10
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Fusion Razor Beam User Manual
11
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

www.prolight.co.uk Fusion Razor Beam User Manual
12