Ergofino AD-NT001 Quick setup guide

ELECTRIC
HEIGHT-ADJUSTABLE DESK
Assembly & Use Manual
Model:
AD-NT001 | AD-NT002 | AD-NT003

Preface
This electric height-adjustable standing desk consists of a heavy-duty steel
desk frame and a motorized height adjustment system. Please read and
completely understand this manual before assembly and use.
FAILURE TO COMPLY WITH OR OBSERVE ALL INSTRUCTIONS AND
WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN
SERIOUS PROPERTY DAMAGE OR PHYSICAL INJURY.
DANGER - To avoid the risk of electric shock, always unplug this
furnishing before cleaning, putting on or taking off parts.
Instruction safety and warnings:
1 1

Keep children away from electric height-adjustable desks, control units, and
keypads. There is a risk of injury and electric shock.
Close supervision is necessary when this furnishing is used by, or near children,
invalids, or the disabled.
Use this furnishing only for its intended use as described in these instructions.
Use attachments recommended by the manufacturer only.
Make sure the power socket/outlet is close to the furnishing in use and easily
accessible.
Never operate on this furnishing when the cord or plug is damaged, it is not
working properly, or it has been damaged or dropped into water.
Keep the cords away from heated surfaces.
Do not open any of the following components: legs, control box, or keypad.
There is a danger of getting electric shock.
WARNING - To avoid the risk of burns, fire, electric shock, or physical injury:
2

Do not insert anything into any seam or opening.
Keep all electrical components dry.
Do not operate this furnishing in an environment where aerosol (spray) products
are being used or oxygen is being administered.
Do not use outdoors.Inappropriate use of this product may cause property
damage or physical injury.
Check surroundings on all sides before use. Body parts and property can be
crushed if trapped in immobile obstacles and the desk's range of motion.
Ensure the length of power cords are accounted for when operating the desk.
Monitors, computers, speakers, anything with a cord that is not long enough for
the desk's range of motion could be pulled down or have its wires broken. Items
pulled off the desk may cause other items to fall.
Pinch Point: Keep hands and fingers clear.Please provide this manual to users,
installers, or support personnel operating the product.
3

MAKE SURE NO OBSTACLES ARE IN THE DESK'S PATH AND ALL CORDS ARE
OF APPROPRIATE LENGTH FOR DESK TRAVEL. FAILURE TO COMPLY WITH OR
OBSERVE ALL ASSEMBLY, SAFETY, AND OPERATION INSTRUCTIONS AND
WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS
PROPERTY DAMAGE OR PHYSICAL INJURY.
Use and Liability:
This height-adjustable desk has two electric motors and is designed for use in dry
work areas only. The desk height is adjustable so that it can be positioned at the
most ergonomically suitable height. These desks are designed only for the
purposes included in this manual. They should not be used in environments with
high humidity or dampness. Any other use is at user's risk. Do not move around,
crawl, or lie under the desk frame. Do not sit or stand on the desk frame. Children
should never use the desk unless they are supervised by adults.
Liability: For damages caused from improper use or handling of the desk other
than those described in this manual, there is no warranty.
4

5
Preparation
5

Checklist
(different)
(Power Wires*1 and Connector Wires*1)
6

Checklist
7

Installation
Step 1: Assembling the feet
Place the lifting column upside
down, put the foot on top.
Align the mounting holes on the
foot with the screw holes on
the lifting column .
Secure the adjustable foot pads
to the feet.
Tighten all 4 screws.
Repeat the same process to assemble
the other foot
8

Installation
Step 2: Assembling the lifting columns 1
Separate (A/B/C/D) and .
9

Installation
Assembling the lifting columns 2
Fix the crossbar A and B to the lifting column with the screws .
10

Installation
Assembling the lifting columns 3
Fix the crossbar C and D to the lifting column with the screws .
11

Installation
Step 3: Assembling the frame
Connect the center rail and the crossbars as shown.
(two sides, screws are not used in this step)
12

Installation
Assembling the frame
13

Installation
Step 4: Assembling the side brackets
Attach the side bracket to the lifting column
with 2 screws for each side.
14

Installation
Step 5: Fixing the crossbar
15
Secure the center rail to the cross- bars
on both sides with 4 screws .
Place the frame on the desktop and
adjust the crossbars to fit the desktop.
We recommend keeping a 5 cm distance
between the side bracket and the edge of the
desktop. (If you purchased the desk frame with
a desktop, please follow the instruction of the
desktop to find the suitable position.)

Installation
Step 6: Assembling the desktop
Secure the desk frame to the desktop with 8
screws on the edge and with 4 Screws
in the middle (at the each side of crossbar A
and C). You need a total of 12 screws and
12 washers .
We recommend to pre-drill the mounting
holes. Before drilling, make sure the
thickness of the desktop is bigger than
25mm. If you purchased the desk frame with
a desktop, please use the screw kit included
in the desktop package.
16

Installation
Step 7: Assembling the handset
Secure the handset to the edge
of the desktop with 2 Pan Head
Screws .
17

Installation
Step 8: Assembling the control box
Secure the control box to the desktop by inserting the control box into the slot.
(No screws needed)
18