RiverRidge 16-007 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® 6-Bin Storage Cabinet
ITEM#: 16-007 ESPRESSO WITH BROWN BINS
ITEM#: 16-008 ESPRESSO WITH GRAY BINS
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN
25 POUNDS PER SHELF THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE
SERIOUS INJURY OR DEATH.

PARTS LIST

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT
INCLUDED) THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED

STEP 1
1. Insert 4 short wood dowels (4) into dowel holes on bottom board (A).
2. Attach 2 divider panels (B) to bottom board (A) by inserting short wood dowels (4)
into wood dowel holes on divider panels (B).
STEP 2
1. Insert 2 short wood dowels (4) into dowel holes on bottom board (A).
2. Attach decorative panel (C) to bottom board (A) by inserting short wood dowels (4)
into wood dowel holes on decorative panel (C).

STEP 3
1. Insert 4 long wood dowels (3) into dowel holes on divider panels (B).
2. Attach shelf (D) to divider panels (B) by inserting wood dowels through dowels holes
on shelf (D).
STEP 4
1. Insert 4 short wood dowels (4) into dowel holes on left side panel (E).
2. Screw in 2 cam bolts (1) into pre-drilled holes on left side panel (E).
3. Attach left side panel (E) to bottom board (A), shelf (D) and decorative panel (C) by
inserting cam bolts (1) and short wood dowels (4) into cam lock holes and short
wood dowel holes on bottom board (A), shelf (D) and decorative panel (C).
4. Insert 2 cam locks (2) into cam lock holes on bottom board (A) and rotate clockwise
to lock cam bolts (1).

STEP 5
1. Insert 4 short wood dowels (4) into dowel holes on right side panel (F).
2. Screw in 2 cam bolts (1) into pre-drilled holes on right side panel (F).
3. Attach right side panel (F) to bottom board (A), shelf (D) and decorative panel (C) by
inserting cam bolts (1) and short wood dowels (4) into cam lock holes and short
wood dowel holes on bottom board (A), shelf (D) and decorative panel (C).
4. Insert 2 cam locks (2) into cam lock holes on bottom board (A) and rotate clockwise
to lock cam bolts (1).
STEP 6
1. Attach 2 divider panels (B) to shelf (D) by inserting long wood dowels (3) into wood
dowel holes on divider panels (B).

STEP 7
1. Insert 4 short wood dowels (4) into dowel holes on bottom of top board (G).
2. Screw in 4 cam bolts (1) into pre-threaded holes on bottom of top board (G).
3. Attach top board (G) to left side panel (E), right side panel (F) and divider panels (B)
by inserting cam bolts (1) and short wood dowels (4) into cam lock holes and dowel
holes on left side panel (E), right side panel (F) and divider panels (B).
4. Insert 4 cam locks (2) into cam lock holes on left side panel (E) and right side panel
(F) and rotate clockwise to lock cam bolts (1).
STEP 8
1. Attach 2 back boards (H) to back of cabinet by inserting 21 wood screws (5) into
holes on back boards (H) and tighten into back of cabinet.

STEP 9
1. Attach 1 bracket (6) to back of assembled cabinet by inserting 1 wood screw (5)
through hole on bracket (6) and tighten into top board (G).
2. According to height of bracket (6) drill hole on wall and insert plastic anchor (7) into
hole on wall.
3. Attached 1 bracket (6) to plastic anchor (7) and wall by inserting wall screw (8)
through hole on bracket (6) and tighten into plastic anchor (7).
STEP 10
1. Place storage cabinet against wall and close to bracket (6).
2. Insert plastic lock strap (9) through hole on bracket (6) assembled on storage cabinet
and through hole on bracket on wall and fasten plastic lock strap (9) to fix 2 brackets
firmly.

STEP 11
1. Take bottom board out from folded storage bin (I).
2. Open folded storage bin and put bottom board into storage bin (I) making sure cloth
tab is facing up.
3. Repeat steps 1 and 2 to assemble 5 more bins.
STEP 12
1. Put 6 small storage bins into cabinet unit.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016