Furniture of America Mayville CM3431SC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-19
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3431SC-2PK
Phillips Screwdriver
(Not Included)

Page 2 of 5

Parts List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 2 pcs x 2
Front Leg
#D x 10 pcs x 2
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
#C x 4 pcs x 2
Bolt 5/16”x2”
Page 3 of 5
#E x 10 pcs x 2
Flat Washer
Hardware List
#A x 4 pcs x 2
Bolt 5/16”x3”
#B x 2 pcs x 2
Bolt 5/16”x1-1/2”
#G x 4 pcs x 2
Screw M4x38mm
#H x 1 pc x 2
Wood Dowel
#F x 1 pc
Allen Wrench
#4 x 2 pcs x 2
Side Leg Support
Note: The above parts and hardware are
shown for a complete assembly of ONE
chair. However, the actual parts and
hardware (with an exception of theAllen
wrench) in the box will be twice the
quantities listed to include the assembly of
the second chair.
X 2

Turn right (clockwise) to tighten
Page 4 of 5
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
#H x 1 pc
Turn right (clockwise) to tighten
#H
I. Place the backrest with legs (#1) on a protected surface. Insert a
wood dowel (#H) into the center hole of the backrest with legs
(#1).
II. Align the seat (#2) with the wood dowel (#H) and the pre-drilled
holes of the backrest with legs (#1).
III. Prepare 2 bolt assemblies by inserting FIRST the lock washer
(#D) onto the bolt (#B) and then the flat washer (#E) onto the
SAME bolt (#B), in that order.
IV. Insert the bolt assemblies through the pre-drilled holes of the
seat (#2) and secure those bolts using the Allen wrench (#F) to
lock them with the backrest with legs (#1).
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#D) onto the bolt (#A) and then the flat washer (#E) onto the
SAME bolt (#A), in that order.
II. Insert the bolt assemblies through the pre-drilled holes of the seat
(#2) and secure those bolts using the Allen wrench (#F) to lock
them with the backrest with legs (#1).
#A x 4 pcs
#D x 4 pcs
#E x 4 pcs

I. Insert the two leg supports
(#4) into the backrest with
legs (#1) and the two front
legs (#3).
II. Align the two front legs (#3)
with the pre-drilled holes of
the seat (#2).
III. Prepare 4 bolt assemblies
by inserting FIRST the lock
washer (#D) onto the bolt
(#C) and then the flat
washer (#E) onto the SAME
bolt (#C), in that order.
IV. Insert the bolt assemblies
through the pre-drilled holes
in the corners of the seat
(#2) and secure those bolts
using the Allen wrench (#F)
to lock them with the two
front legs (#3).
Page 5 of 5
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR.
Turn right (clockwise) to tighten
I. Secure the two leg supports (#4) with 4 screws (#G) using a
Phillips screwdriver to lock them with the backrest with legs (#1)
and the two front legs (#3).
II. Carefully turn the completed chair upright. Make sure the chair is
rested on a flat surface and does not feel loose or wobbly. If it
does, double check that the bolts are secured and properly
tightened.
#G x 4 pcs
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten