Welton USA MB922 User manual

CourtneyMODEL : MB922
Welton USA 03-21-12
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 4
may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY HARDWARE UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.
MADE IN VIETNAM
(#40-218)
*HARDWARE KIT 92W1639
PANEL
LEFT END
FULL BED 1
BFULL BED RIGHT END
PANEL 1
CTWIN BED LEFT END
PANEL 1
DTWIN BED RIGHT END
PANEL 1
EFRONT
RAIL 1
FREAR
RAIL 1
GFRONT
GUARDRAIL 1
HREAR
GUARDRAIL 1
I LADDER 1
JSLAT SUPPORT BAR
92W1641 1
KSLAT SUPPORT
92W1642 2
DESCRIPTION QTY.
A
ITEM ITEM DESCRIPTION QTY.
LFULL BED
SLAT ROLL 1
MTWIN BED
SLAT ROLL 1
N* M6 X 60mm
SCREW 2
O* M6 X 90mm
SCREW 19
P* M6
BARREL NUT 19
Q* M10 X 40mm
WOOD DOWEL 8
R* M6 X 30mm
SCREW 16
S* M6 X 40mm
SCREW 4
T* M4 X 30mm
WOOD SCREW 40
U* LOCATING
PIN 4
V* M6 X 30mm
LEVELER 2
W* M4
HEX KEY 2
EN
!
WARNING:
-This package contains small parts.
Keep away from children duringassembly.
-Adultassemblyrequired.
- Phillips head screw driver required.
- Instructions are generic. Figures may vary.
- Screws left after assembly should be kept
out of reach of children.

ASSEMBLY INSTRUCTIONS
Courtney
PAGE 2 OF 4
MODEL : MB922
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
T
Q
BARREL NUTS(P) AND 8 SCREWS(O) USING HEX KEY(W) AS SHOWN.
E
ATTACH FRONT AND REAR RAILS(E,F) TO THE FULL BED LEFT AND RIGHT END PANELS(A,B) WITH 4 DOWELS(Q), 8
STEP 1
P
R
2 SCREWS(N).
ATTACH THE FULL BED SLAT ROLL ASSEMBLY TO THE FULL BED FRAME WITH 8 SCREWS(R) AND 20 WOOD SCREWS(T)
AS SHOWN.
N
K
R
J
V
TR
W
O
A
F
B
STEP 2
ATTACH 1 SLAT SUPPORT BAR(J), 2 SLAT SUPPORTS(K) AND 2 LEVELERS(V) TO THE FULL BED SLAT ROLL(L) WITH
L

R
T
SHOWN.
STEP 4
ATTACH THE TWIN BED SLAT ROLL(M) TO THE TWIN BED FRAME WITH 8 SCREWS(R) AND 20 WOOD SCREWS(T) AS
ATTACH FRONT AND REAR GUARDRAILS(G,H) TO THE TWIN BED LEFT AND RIGHT END PANELS(C,D) WITH
4 DOWELS(Q), 11 BARREL NUTS(P) AND 11 SCREWS(O) AS SHOWN.
R
G
H
M
C
D
Q
P
R
STEP 3
O
T
Courtney
PAGE 3 OF 4
ASSEMBLY INSTRUCTIONS
MODEL : MB922
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com

I
S
ATTACH THE TWIN BED TO THE FULL BED WITH 4 LOCATING PINS(U).
STEP 5
U
STEP 6
ATTACH LADDER(I) TO THE ASSEMBLY WITH 4 SCREWS(S).
S
ASSEMBLY INSTRUCTIONS
Courtney
PAGE 4 OF 4
MODEL : MB922
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com

1-800-759-1559
Maximum allowable weight on top bunk : 150 lbs.