ergonofis Shift User manual

Installation
guide

Thanks for choosing
our products, you help
us spread a message that
we hold very close to our
hearts: the importance
of moving a little more
every day.
If you have any questions
regarding our products, call
us at 1-877-37-STAND.
To know more about our products
and services, visit our website at
ergonos.com.

Assembly instructions 5
Table parts and hardware 6
Step 1- Unfold the lifting columns 8
Step 2- Attach side brackets to lifting columns 10
Step 3- Adjust the rail to the proper length and secure the rail 12
Step 4- Secure the frame to the work surface 14
Step 5- Attach the feet 16
Step 6- Attach the ergonofis handset 18
Step 7- Wire management 20
Step 8- Turn the desk upright 22
Handset user guide 24
Technical data 25
Initializing 26
First use 26
Saving a position 26
Recalling a saved position 27
Setting height limits 27
Locking - Unlocking the desk 28
Removing height limits 28
Intelligent system protection (ISP) 29
Troubleshooting 30
Warranty 31
Table of contents

Assembly
instructions
english version

6
Table parts and hardware
Included
1. Lifting column (2)
2. Foot (24” or 30”) (2)
3. Support rail set (1)
4. Side bracket - Right hand (1)
5. Side bracket - Left hand (1)
6. Glides, they are pre-assembled on the feet (4)
7. Control Box (1)
8. Power cable (1)
9. ergonofis Handset (1)
10. Wire management kit (1)
11. Table top (only when purchased a complete desk)
12. M6x 12mm screw (4)
13. Round M8x 20mm head screw (8)
14. Button head ST5.0x 23mm screw (16)
15. Pan head ST3.5x 16mm screw (4)
16. M5Allen key (1)
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
> Star screwdriver or drill (ideally a drill
for a faster installation).
Not included

7

8
Unfold the lifting columns
* * * Caution * * *
> We highly suggest being two to unbox the frame and to unfold
the lifting columns.
> Be careful not to squeeze your fingers while unfolding the
lifting columns.
> Be careful not to squeeze the cables while unfolding the
lifting columns
Step 1

9

10
Attach side brackets to lifting columns
You will need your lifting columns (2), side brackets (2),
M6x 12mm screw (4) and the M5Allen key.
1. Insert the side brackets in the lifting column. Make sure the
side holes are aligned.
2. Screw the side bracket into the lifting column using your
M6x 12mm screws (4) and the provided M5Allen key.
3. Repeat with the second column.
Step 2

11
1
2

12
Adjust the rail to the proper
length and secure the rail
You will need the frame (composed of the lifting columns, the side
brackets, and the rail) and the M5Allen key.
1. Set frame on the underside of the worksurface (table top),
loosen the screws that are in the rails (the screws are already in
the proper holes in the frame), and then align the frame holes
with the pre-drilled holes in the worksurface.
2. Secure the rails by rotating the screws mentioned above
clockwise using the M5Allen key until they’re tight.
Step 3
Note: If no holes are pre-drilled, adjust the frame to the proper
length and center it on the underside of the worksurface. Follow
step 2listed above (step 2of step 3) and drill the holes in the
worksurface.

13
2
1

14
Secure the frame to the work
surface (table top)
You will need the frame, the button head ST5.0screws (16),
and a screwdriver or a power drill.
1. Double check to make sure everything is centered on the
pre-drilled holes, then, using the button head ST5.0screws (16),
secure the frame to the table.
Step 4

15

16
Attach the feet
You will need your feet (2), the round M8x 20mm head screws (8),
and the M5Allen key.
1. Ax the foot to the column.
2. Secure the foot to the column using the round M8x 20mm head
screws and the M5Allen key.
3. Repeat with remaining foot and column.
Step 5

17

18

You will need your handset, the pan head ST3.5screws (4), and a
screwdriver or a power drill.
1. Locate the four pre-drilled holes for the handset.
2. Secure the handset to the table top using the pan head
ST3.5screws (4).
Step 6
Note: Review the handset guide in order to use the handset once
the installation is complete.

19

20
Wire management
You will need the wire management kit
1. Connect the handset to the control box.
2. Connect the cables from each leg into the control box.
3. Connect the power cord to the power port on the control box
(the other end of the power cable will go into an outlet).
4. Use the cable loops to screw the loose cables under the table
top to make sure that they don’t hang once you turn the desk
upright. (attach loose cables in between the rails to hide them).
Step 7