GO2 VERONICA User manual

Assembly Instructions
GO2X00012 REV. A |
1. Place work surface on a soft surface to protect from
damage – groove-side up and grommet cutout towards
back. Fig.1
2. Remove all contents from bookcase including false
floor and shelf. Carefully flip upside down onto work
surface, with opening facing outward inset 1/2" from
the front and sides. Align bookcase with pre-drilled
holes and fasten using seven 5/8" Phillips wood
screws. Fig.1
Do NOT use the 1" Phillips wood screws to attach
bookcase as they will penetrate work surface.
3. Position each leg 1" inset on two sides and align with
predrilled holes. Fasten leg using eight 1" Phillips wood
screws. Repeat for other leg. Fig.1
4. Install the four leveling glides in the bottom of the
bookcase, turning by hand. Fig.1
5. Carefully flip desk assembly upright. Fig.2
6. Move desk to desired location.
7. Place level on work surface and adjust for level
both side-to-side and front-to-back. Leveling glides on
both legs can be turned by hand as needed and four
levelers located inside bookcase floor can be adjusted
with a 1/4" hex socket driver. Fig.2
8. Place false floor in bottom of bookcase. Install four
shelf clips and shelf.
Fig. 1
Fig. 2
1"
1"
1/2"
1/2"
1/2"
1/2"
(16) 1" Phillips
wood screws
(4) leveling glides
grommet cutout
towards back
groove-side up
front
(7) 5/8" Phillips
wood screws
Two
Person
Lift
GO2X00012 REV. A | VERONICA DESK ASSEMBLY
power drilltape measure #2 Phillips
driver
(7) 5/8" Phillips
wood screws
(16) 1" Phillips
wood screws
1/4" hex
socket
level (4) leveling
glides
(4) shelf clips
For proper care and
cleaning instructions visit
http://go2wfh.com/resources
Tools Needed: Hardware Included:
go2wfh.com

Assembly Instructions
(16) 1" Phillips
wood screws
1"
1"
1/2"
1/2"
1/2"
1. Place work surface on a soft surface to protect from
damage – groove-side up and grommet cutout
towards back.
2. Remove all contents from locker including false floor
and shelf. Close door and carefully flip locker upside
down onto work surface, facing front with 1/2" inset on
all three sides, and handle toward center of work
surface. Fig.1
3. Open door and align locker with pre-drilled holes.
Fasten to work surface using six 5/8" Phillips wood
screws. Fig. 2
Do NOT use the 1" long Phillips wood screws to
attach locker as they will penetrate work surface.
4. Position leg 1" inset on two sides and align with
predrilled holes. Fasten using eight 1" Phillips wood
screws. Repeat for remaining leg. Fig. 2
5. Install four leveling glides in bottom of locker, turning
by hand. Fig. 2
6. Close door and carefully flip desk assembly upright.
Move to desired location. Open door.
7. Place level on work surface and adjust for level both
side-to-side and front-to-back. Leveling glides on both
legs can be turned by hand as needed and four
levelers located inside locker floor can be adjusted
with a 1/4" hex socket driver. Fig.3
8. Place false floor in bottom of locker. Install four shelf
clips and shelf.
(6) 5/8" Phillips
wood screws
(4) leveling glides
Fig.1
Fig.2
Fig.3
grommet cutout
towards back
groove-side up
front
Two
Person
Lift
GO2X00012 REV. A | ARCHIE DESK ASSEMBLY
power drilltape measure #2 Phillips
driver
(6) 5/8" Phillips
wood screws
(16) 1" Phillips
wood screws
1/4" hex
socket
level (4) leveling
glides
(4) shelf clips
Tools Needed: Hardware Included:
go2wfh.comgo2wfh.com
For proper care and
cleaning instructions visit
http://go2wfh.com/resources