Ergotron Neo-Flex Wall Mount Lift User manual

1 of 10
ABCD
1
2
3
44x
M4 x 10mm M4 x 10mm
4x 4x
4mm 2x
4x
4x
1x 1x
1x 1x
1x
1x
1x
1x
M4 x 5mm
4x 1x
M6 x 7mm
M6 x 10mm
10mm
ASSEMBLY INSTRUCTIONS
Neo-Flex™ Combo Lift
FRONT
Add a separate keyboard and mouse to create a productive workstation.
6-12 lbs
(2.7-5.4 kg)
6-16 lbs
(2.7-7.3 kg)

2 of 10
NOTE: This product is meant to be used with an inde-
pended keyboard and mouse (purchased separately).
Use of the laptop keyboard is not recommended.
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain at.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
Set Your Workstation to Work For YOU!

3 of 10
4mm
4x M6 x 7mm
1a
b
4mm
4x
M6 x 10mm
BACK
FRONT
BACK
FRONT

4 of 10
b
d
c
c
e
d
f
aab
1x
1x
M4 x 5mm
M4 x 5mm
2
10mm
10mm
1x
1x
M4 x 5mm
M4 x 5mm
180˚ 180˚

5 of 10
3
75x75mm
100x100mm
45
4x
4x
M4 x 10mm
M4 x 10mm
Temporarily place your laptop (or laptop and docking station) on the
tray in order to align with monitor in the following adjustment steps.

6 of 10
Vertical Adjustment
Side-to-Side Adjustment
Forward and Back Adjustment
To ensure stability, the docking station SHOULD NOT
extend over the back of the tray.
Center total width of mounted equipment on stand.
a
b
c

7 of 10
To ensure stability, the docking station SHOULD NOT extend over
the back of the tray.
Attach Laptop to Tray
bc
d
a
6
ab
Laptop with docking station
Laptop Only

8 of 10
8
7
It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this product,
resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments ared i f f icult and do not stay in the desired position, follow the
instructions to loosen or tighten the tension to create a smooth, easy adjustment motion. Depending on your product and the adjustment, it may take several turns to notice a difference.
It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this product,
resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Cable Routing

9 of 10
b
Follow these instructions to tighten or loosen tension.
Tilt – Forward and Backward
4mm
Follow these instructions to tighten or loosen tension.
Lift – Up and down
a
Check out the collection of computers & hardware we offer.