Ergotron LX Sit-Stand User manual

1 of 15
888-45-311-W-01 rev.J • 12/18
5°
70°
360°
360°
180°
20"
(508 mm)
0.78”-2.25” (20-57mm)
0.5"-2.5" (13-64mm)
1/4"
0.78"-2.56"
(20-65mm)
14-30 lbs
(6.35-13.61 kg)
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
LX Sit-Stand
Desk Mount LCD Arm
Tools Needed
Maximum Screen
Size* = 42”
*Limited to 25 lbs
maximum
User's Guide
English
For the latest User Installation Guide please visit: www.ergotron.com

2 of 15
888-45-311-W-01 rev.J • 12/18
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the
full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in
desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your
product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed
from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps
to ensure safe and optimum operation.
CAUTION: DO NOT rotate monitor past rear edge of desk. Doing so will create an unstable
situation and may cause equipment damage or personal injury.

3 of 15
888-45-311-W-01 rev.J • 12/18
ABCD
1
2
3
4
5
6
M4 x 10mm
M4x12mm M5x12mm M6x12mm
4x 4x 4x
1x
5mm 4mm
1x
1x
4x
4x
1x
1x
1x
1x
1x
2x
1x
1x 1x
1x
1x
1x
4x 4x
4x
4x
M8 M5 Kit
2x
M4 x 10mm
M3 x 6mm
M8-M5
Reducer
M5 x 7mm
M5x20mm
1/4”
8mm
1x
2.5mm
M6
M6 x 45mm
Components

4 of 15
888-45-311-W-01 rev.J • 12/18
1/4"
1/4”
8mm
1x
1x
1x
1x
c
d
a
b
1
4mm
4mm
4mm
4mm
0.78"-1.38" (20-35mm) 1.18"-2.56" (30-65mm)
CAUTION: Bolt must be
centered in hole.
CLAMP GROMMET HOLE
DESK THICKNESS

5 of 15
888-45-311-W-01 rev.J • 12/18
0˚
2
iii
M3 x 6mm
Portrait / Landscape Options
OPTION i If you want full portrait/landscape rotation, skip to step 8 on the next page.
OPTION ii If you do not want your TV/Monitor to rotate all all, you can stop rotation by inseting
the set screw.

6 of 15
888-45-311-W-01 rev.J • 12/18
3
A
B
C
D
75x75mm
100x100mm
100x200mm
200x200mm
200x100mm
100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
200mm (7-7/8”)
100mm (3-15/16”)
200mm (7-7/8”)
7
8
8
8
VESA Adapter
Congurations
TV/Monitor Hole
Pattern Sizes
Check size of
TV/Monitor hole
pattern

7 of 15
888-45-311-W-01 rev.J • 12/18
OR
A
75x75mm
100x100mm 100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
75mm (2-15/16”)
3
410
M4 x 10mm
M4 x 10mm
4x
M4 x 10mm
Mount Type A TV/Monitor to Arm

8 of 15
888-45-311-W-01 rev.J • 12/18
BCD
3
M5 x 7mm
4x
Mount VESA Adapters to Arm based on TV/Monitor hole
pattern size (B, C, or D) .

9 of 15
888-45-311-W-01 rev.J • 12/18
OR
OR
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
200mm (7-7/8”)
100mm (3-15/16”)
200mm (7-7/8”)
BCD
M4x12mm
M5x12mm
M6x12mm
3
410
10
M4x12mm
M5x12mm
M6x12mm
Mount Type B, C, or D TV/Monitor to Arm
NOTE: To reduce M8
holes for use with M5
screws, or if you have a
model with Samsung
holder rings, follow the
M8M5 KIT instructions
on the next page.

10 of 15
888-45-311-W-01 rev.J • 12/18
M8M5 KIT Instructions
NOTE: follow this step only if your TV/monitor has M8 holes which need to be reduced
to M5 or for Samsung models using the holder ring.
Install M8M5 reducer bushing to TV/Monitor and use M5 x 20 mm
monitor screws to secure when using the Samsung holder ring.
M5 x 20mm
Monitor Screw
TV/Monitor Mounting
M8 size hole
M8M5 Reducer Bushing
Holder Ring
(Not included *Samsung Only)