Ergotron StyleView User manual

1 of 23
888-45-208-W-02 rev. N • 10/19
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
StyleView Sit Stand Combo System
with Medium CPU Holder
For the latest User Installation Guide please visit: www.ergotron.com

2 of 23
888-45-208-W-02 rev. N • 10/19
10mm
11 mm
13 mm
17mm
7/16"
11mm 1/4"
> 3"
Ø 3/8" (10 mm) Ø 1/2" (12.8 mm)
Ø 7/32" (5.6 mm)
The Combo Arm can be modifi ed to mount displays up to 25 lbs
(11.3 kg), however display lift and tilt motion will not be possible if
this option is chosen. Refer to special instructions on page 14.
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the
full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in
desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your
product and the adjustment, it may take many turns to notice a diff erence. Any time equipment is added or removed
from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps
to ensure safe and optimum operation.
Tools Needed
Stud Finder

3 of 23
888-45-208-W-02 rev. N • 10/19
M4 x 10mm M4 x 10mm
M6 x 10mm
M6 x 70mm M4.2 x 25mm
M6
1/4-20 x 2"
M8 x 16mm
M4 x 8mm M4 x 6mm
M10 x 12mm M10 x 16mm
M3.5 x 8mm
M5 x 15mm
3 mm
6mm
Components
Optional Weight Capacity Modifi cation Fasteners
Flat Head Pan Head

4 of 23
888-45-208-W-02 rev. N • 10/19
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5’3”-5’9”
(160-175cm).
If user heights are diff erent than this, you should change mounting height to accommodate user heights. (Change
mounting height one inch for every one inch diff erence in user heights).
Mounting height assumes there is a 6” (152 mm)
distance between the center of your monitor
mounting holes and the top of the screen. If your
distance is smaller, you should increase mount-
ing height accordingly, if your distance is larger,
you should decrease your mounting height ac-
cordingly.
Top view showing range of motion when pulled out from the wall.
Front view with arm pushed back against the wall.

5 of 23
888-45-208-W-02 rev. N • 10/19
Ø 3/8" (10 mm) Ø 1/2"
1/4-20 x 2"
M6
"
gauge steel
"

6 of 23
888-45-208-W-02 rev. N • 10/19
3-1/8"
(80 mm)

7 of 23
888-45-208-W-02 rev. N • 10/19
M6 x 70mm
M6

8 of 23
888-45-208-W-02 rev. N • 10/19
"
gauge steel
"

9 of 23
888-45-208-W-02 rev. N • 10/19
1/4-20 x 2"

10 of 23
888-45-208-W-02 rev. N • 10/19
3mm
M6 x 10mm
M10 x 12mm
M6 x 10mm
M10 x 16mm
6mm