Erone SEL39R433-PP4 Operation and maintenance manual

ERONE - RX CARD 4CHPP
1A - Main features
The receiver ERONE 433 mod. SEL39R433-PP4 is a card receiver
with 4 push-pull outputs. It has a high security coding system
( 19683 code combinations) .The operating frequency is among the
European harmonised frequencies;
The receiver has 4 digital outputs with push-pull configuration and
current in sink and source of 25 mA
The receiver has a special pin-out so it can be connected only to
SEL39R433-PP4
NOTICE
INSTRUCTIONS
1B - Technical specifications
Receiver type Superheterodyne
Carrier frequency 433,92 MHz
Local oscillator frequency 6,6128 MHz
Demodulation AM/ASK
Local Oscillator VCO / PLL
Channel width > 25 KHz
Intermediate frequency 10.7 MHz
Input sensitivity -115 dBm
Local oscillator spurious emissions < -57 dBm
Input load: 50 Ohm
Power supply: 12 Vdc
Consumption: 11 mA
Outputs 4
Output type Push-pull
Max sink current on 4 outputs 25 mA
Max source current on 4 outputs 25 mA
Max sink/source current on 1 output 125 mA
Memory capacity 100 TX
Security code Rolling code
Max code combination number 19683
Operating temperature -20°/+80°C
Weight gr. 9
Overall dimensions (mm) 44 x 42 x 8
compatible appliances. Hereby, CDVI Wireless Spa, declares that the
radio equipment type 4 is in compliance with directive
2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: www.erone.com.
COMPATIBLE TRANSMITTERS
!Erone Type SETDS39433E2: 2 key transmitter
!Erone Type SETDS39433E4: 4 key transmitter
SEL39R433-PP
SUMMARY
1A - Main features
1B - Technical specifications
1C - Layout and connections
1 - INTRODUCTION
2 - TRANSMITTER MEMORIZATION
3 - SINGLE TRANSMITTER CANCELLATION
4 - MEMORY ERASURE
5 - MEMORY FULL
T H E S M A R T L I V I N G
Thank you for choosing a product Erone.
You are recommended to read carefully this manual before installing the
product.

The guarantee period of all Erone products is 24 months, beginning from
the manufacturer date. During this period, if the product does not work
correctly, due to a defective component, the product will be repaired or
substituted at the discretion of the producer. The guarantee does not cover
the plastic container integrity. After-sale service is supplied at the
producer's factory.
GUARANTEE
Manufactured by CDVI Wireless Spa
Via Piave, 23 - 31020
San Pietro di Feletto (TV) - Italy
Tel.: [phone] - Fax.: [phone]
E-Mail: [email protected] - Web: www.erone.com
IS-RPP39ERUK Rev. 1 del 13.06.2017
3 - SINGLE TRANSMITTER CANCELLATION
2 - TRANSMITTER MEMORIZATION
5 - MEMORY FULL
1D - Layout and connections
The receiver makes the memorization of the transmitters buttons in
sequential way, by using the button P1
Each operation is confirmed by the leds L1, L2, L3, L4.
The led activation is cyclic: at each activation of P1 a led switches on
and the previous switches off.
Keep the button P1 pressed down until the red led L1 switches on ,
release P1 and push the key “A” of the transmitter ; after push again P1,
the second red led L2 switches on , release P1 and push the key “B” of
the transmitter. After a while both the led will switch off and the
procedure will be finished.
In this way the keys “A” and ”B” of the transmitter activate the outputs
OUT1 and OUT2 of the receiver.
The procedure to follow for the keys ”C” and “D” is the same as above.
For the memorization of the “C” key on K3 push P1 3 times, and for the
memorization of the “D” key on K4 push P1 4 times.
L1 L2 L3 L4
For multiple transmitter memorization, first select the right output
position with P1, and then push the keys of all the transmitters you want
to memorize, without leaving the corresponding led to switch off.
Select the right output to which the transmitter was connected by
pushing P1, as indicated in the previous paragraph. Then push the
key of the transmitter to cancel : L3 and L4 will blink twice to
confirm.
Repeat the same procedure for all the transmitter keys to cancel.
4 - COMPLETE MEMORY ERASURE
Keep the button P1 pressed down until the first red led L1 switches on,
release it, push it again and keep it pushed down until 3 blinks of the red
led L3 and green led L4 occur.
In this way the memory is completely cancelled.
In case of memory full, that means 100 transmitters are already stored,
if one try to store an extra transmitter, a sequence of 3 blinks of L3 and
L4 occurs and the operation fails.
L4
L3
L2
L1
P1