ERTF Unik 2 User manual

ERTF Compétition [e-mail] – www.ertf.com
Parc technologique de Soye - 56275 Ploemeur Cedex Tél [phone] - Fax [phone]
Mounting advices Unik² GPS-Sentinel Car/Truck
Bracket
:
Dimensions
: 180 x 155 x 24mm
The mechanical assembly shall be flexible and integrate the 4 provided silent blocks to absorb
vibrations
GPS fixing through the bottom and binding by 2 auto-blocking screws assembled on the GPS
Minimal dimensions to apply or the bracket installation:
For connectors, leave at least 4cm of free space
behind bracket
If 2 GPS are close
installed, leave at least 9cm between axes
Power supply
:
The power supply will have to be protected by a minimal fuse of 3A and to deliver a controlled
tension ranging between 9 and 24 continuous volts
The main circuit breaker of the vehicle has to act on the positive but the
GPS must be directly connected.
Autonomy/Consumption
Main power supply : Supply on internal battery :
Consumption under 12V: Autonomy with blacklighting “ON”:
-220 mA with backlighting by default drive (60%) - 4h with repeater
- 270 mA with backlighting ON - 9h without repeater
Sentinel Alarm button
(
red
)
:
The driver and the codriver must be both able to activate the Alarm Sentinel.
Alarm button is connected on the power supply cable (3 points connector)
The button must be accessible for both crew members
Sentinel
push
-
button
(
yellow
)
:
Push-button is connected on the power supply cable (2 points
connector)
Sentinel
buzzer
:
Buzzer is connected on the top of the GPS
An optional flash is directly connected to buzzer
Sentinel aerial
:
Sentinel aerial cable is connected on the right top of the GPS (blue sheath with « SENT ERTF » inscription) The
connector is spotted by a blue point
Installation with
the
2 collier straps and
braces given (COMPULSORY) on the
vertical roll bar on the right side, in the
top and the nearest of the windshield
IMPORTANT : Sentinel aerial must
« see » the road and shall be located
not less than 2cm from any surface (no
installation on the dash board)
The aerial must be fixed vertically on the right
side of the windshield in the top, at more than
5cm from any metallic parts
IMPORTANT: the Sentinel aerial must “see”
the road (no installation near metallic parts,
only stick it on the glass)
GPS
cable antenna
(3m)
:
GPS cable antenna is connected on the right bottom side of the GPS
GPS
antenna
:
A TNC type connector must be placed under the car aerial, which is fixed with an M18 wing (do
not forget to make a 20 mm-hole on the roof for the connector)
If you mount two GPS in the same vehicle, let at least 1m between the two aerials.
Stick
aerial
S
o t
aerial
OR

ERTF Compétition
Parc technologique de Soye - 56275 Ploemeur Cedex
tél [phone] - fax [phone]
[e-mail] – www.ertf.com
Matériel nécessaire à l’installation de l’Unik² (GPS+Sentinel intégré) Auto/Camion
Accessories needed to install Unik² (GPS+integrated Sentinel) Car/Truck
Ces 8
éléments sont INDISPENSABLES à l’installation et au onctionnement
de l’Unik²
:
These 8 accessories are ESSENTIAL to install and use Unik² :
1.
Support/
racket
Re . SUPC 101
2. Alarme Sentinel/Alarm Sentinel Re . SEAL 106
3. Bouton-poussoir/Push-button Re . SERA 106
4. Câble alimentation/Power supply cable Re . CALC 901
5. Buzzer Sentinel/Sentinel buzzer Re . SONO 106
6. Antenne Radio Sentinel/Sentinel aerial Re . AESE 106/906
7. Câble antenne GPS/GPS antenna cable Re . CAAE 101
8. Antenne GPS/GPS antenna Re . ANTEC 101
1.
Support
/
racket
Dimensions : 180 x 155 x 24mm
4. Câble
alimentation
/ Power supply
cable
Comprend : câble + porte-fusible 3A
Includes : cable + fuse 3A
5
. Buzzer Sentinel
110dB
7. Câble antenne GPS /
GPS antenna cable
L : 3m
8. Antenne GPS /
GPS antenna
Dimensions : Ø 63mm / H : 40,5mm
6. Antenne radio Sentinel
Sentinel aerial
Connexion du bouton
-
poussoir
Push-button connection
3. Bouton
-
poussoir
/ Push
-
button
(Jaune / yellow)
2
.
Bouton Alarme Sentinel
Alarm Sentinel button
(Rouge
/ red)
Optional lash
Re . FLASH 106
OU
OR