ESCALADE GOALIATH GOTEK50 User manual

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
A S S E M B L Y I N S T R U C T I O N S
Contact Escalade® Sports customer service department at:
Phone: 1-888-USA-GOAL Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [email protected]
Please Do Not Return This
Product to the Store!
2020 Escalade Sports
2L-7604-06
MODEL NO.
B8300
G O T E K 5 0
P O R T A B L E B A S K E T B A L L

2
3/8” drive ratchet wrench
3” or longer extension
#2 Philips Head Screw Driver
10mm socket and wrench
13mm socket and wrench
16mm socket and wrench
17mm socket
19mm socket and wrench
4’ step ladder or other 4’ support
P R E - A S S E M B L Y T I P S
Contact Escalade® Sports customer service department at:
Phone: Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please Do Not Return This Product To The Store!
1-888-USA-GOAL
2020 Escalade Sports
P R E - A S S E M B L Y T I P S
8” Adjustable Wrench
Rubber Mallet
¼” tip drift punch or 5/16” dia. X 8” long metal rod to assist with hole alignment
Utility knife or Rat Tail file to clear excess paint from holes
Funnel
3/8” Allen Wrench
Materials to cushion parts during assembly to prevent scratches/dings
Wooden Block (at least 3”x3”)
2L-7604-06
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 7 to identify and sort all fasteners. Check all cartons for kits.
All hardware may not be located in one kit. Please keep your box it could be used as an assembly aid. See page 29.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
6. Tools required for assembly: Tools recommended for assembly:
To view a video showing how to
assemble this basketball system
please visit our YouTube page at:
https://www.youtube.com/watch?
v=jwuQQaHTw6Q
or scan with your
smart phone.

3
!If using a ladder during assembly, use extreme caution.
!2 capable adults are recommended for this operation.
!Check base daily for leakage. Leaks will cause system to fail.
!Assemble the pole sections properly (if applicable). Failure to do so could cause pole sections to
separate during play or transport.
!Minimum operational height is 6'6" (1.98m) to the bottom of backboard.
SAFETY INSTRUCTIONS
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY
DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully.
Check entire box and inside packing material for parts and/or additional instruction material. Before
beginning assembly, read the instructions and identify parts using the hardware identifier and parts list
in this document. Proper and complete assembly, use and supervision is essential for proper operation
and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not
installed, maintained, and operated properly.

4
Green
sticker
BREAK AWAY RIM
4A-8069-00
MIDDLE POLE
1A-7912-00
TOP POLE
1A-7913-00
BACKBOARD ASSEMBLY 50 X 33
4A-8059-00
LOWER POLE
1A-7910-00
ROLLING FRAME
1A-7903-00
BALLAST FRAME
1A-7904-00
1
54 44
51
2
3
(QTY. 1) (QTY. 1)
(QTY. 1)
(QTY. 1) (QTY. 1) (QTY. 1) (QTY. 1)
BALLAST
3M-8991-00
(QTY. 1)
P A R T S L I S T ( N O T A C T U A L S I Z E )
RIM NET
(QTY. 1)
58
3F-6070-00
50
12
Red
Sticker
Warning
Decal
Red
Sticker

5
LOWER BOARD ARM
8S-7713-00
UPPER BOARD ARM
8S-7712-00
AXLE
8S-7710-00 AXLE ROD
1B-7140-00 BRACE TUBE, RH
8S-7708-00
BRACE TUBE, LH
8S-7709-00
52 49
19
18
9
4
ACTUATOR BAR
1A-7920-10
(QTY. 1) (QTY. 2) (QTY. 2)
(QTY. 1)
(QTY. 1)
(QTY. 1) (QTY. 1)
P A R T S L I S T ( N O T A C T U A L S I Z E )
BOARD ARM CAP
3M-9017-00
56
(QTY. 6)
(Pre-assembled to
Board Arms)
53
(Actuator Bar Cap
Pre-installed)
(Packed inside of
Top Pole)
(Has a sticker on it)green
green sticker
on here
(Has a sticker on it)red
red sticker
on here

6
Wheel Assembly (Parts pre-assembled to wheel)
BALLAST CAP
3M-8996-00
BALLAST CAP WASHER
3M-8999-00
REINFORCEMENT PLATE
8S-7711-00
POLE CAP
3M-8997-00
BUSHING, BOARD ARM
3M-8994-00
AXLE BUSHING
3M-9003-00
Wheel Hub, Outside
3M-9001-00
Wheel Hub, Inside
3M-9002-00
SPRING
5V-6041-00
BACKBOARD BOX
1A-7905-00
ACTUATOR GRIP
3M-9034-00
ACTUATOR LOCK ASSEMBLY
4A-8141-10
38
14
40 31
26
13
37
55
25 586
(QTY. 1)
(QTY. 1)
(QTY. 1)
(QTY. 1)
(QTY. 1)
(QTY. 1)
(QTY. 1)
(QTY. 1)
(QTY. 2)
(QTY. 2)
(QTY. 2)
(QTY. 4)
P A R T S L I S T ( N O T A C T U A L S I Z E )
Wheel
3M-8992-00
7
(QTY. 2)
WHEEL PLUG
3M-9004-00
41
(QTY. 2)
42
O-RING
3M-8998-00
(QTY. 2)
(Pre-assembled to
Wheel Plug)
(Pre-assembled to
Ballast Cap)
Wheel Plug Key
3M-9022-00
(QTY. 1)
57
(Pre-assembled to
Top Pole)
(3/8” Allen Wrench
can be substituted
for Wheel plug key)
(Pre-assembled to
Ballast)

7
HEX HEAD BOLT M8-1.25 X 65mm
1B-7077-00
HEX HEAD BOLT M10-1.5 X 100mm
1B-7078-00
HEX HEAD BOLT M10-1.5 X 110mm
1B-7079-00
HEX HEAD BOLT M10-1.5 X 65mm
1B-7081-00
HEX HEAD BOLT M10-1.5 X 210mm
1B-7080-00
HEX HEAD BOLT M10-1.5 X 25mm
1B-7082-00
HEX NUT M10-1.5, WITH CAP
2B-6799-00
HEX NUT M10-1.5
2B-6796-00
WASHER _ CURVED M10
2B-6802-00
HEX LOCK NUT M12-1.75
2B-6805-00
HEX LOCK NUT M10-1.5
2B-6801-00
WASHER M8
2B-6797-00
WASHER M10 X 30mm
2B-6795-00
WASHER M10
2B-6800-00
WASHER M12 X 24mm OD
2B-6804-00
HEX HEAD BOLT M10-1.5 X 220mm
1B-7085-00
Hex Lock Nut M8-1.25
2B-6808-00
WASHER, NYLON
3M-9000-00
21
29
11
17
24
10
27
28
23
16
39
30
34
22
20
15
36
(QTY. 3)
(QTY. 1)
(QTY. 3)
(QTY. 6)
(QTY. 4)
(QTY. 5) (QTY. 24) (QTY. 4)
(QTY. 8)
(QTY. 4)
(QTY. 4)
(QTY. 15)
(QTY. 2)
(QTY. 6)
(QTY. 4)
(QTY. 1)
(QTY. 2)
H A R D W A R E I D E N T I F I E R ( A C T U A L S I Z E )
35 (QTY. 2)

8
HITCH PIN
7B-6577-00
WASHER, LOCK INTERNAL-TOOTH
2B-6806-00
Philips Head Screw M6-1 X 60mm
1B-7123-00
HEX LOCK NUT M6-1
2B-6803-00
ACTUATOR ROLLER
3M-9035-00
#10-14 X 0.63 Trilobular Screw for Plastic
1B-7084-00
47
48
46
32
43
33
(QTY. 1) (QTY. 1)
(QTY. 1)
(QTY. 2)
(QTY. 1)
(QTY. 2)
H A R D W A R E I D E N T I F I E R ( A C T U A L S I Z E )

9
HEX HEAD BOLT M10-1.5 X 65mm
1B-7081-00
35
(QTY. 2)
23
WASHER M10
2B-6800-00
(QTY. 4)
HEX LOCK NUT M10-1.5
2B-6801-00
24
(QTY. 2)
35
23
24
2
3
HARDWARE NEEDED (ACTUAL SIZE)
DETAIL A
1. Assemble parts 2 & 3 as shown. Tighten hardware
finger tight only.
Prepare a flat area that is clear of debris. Keep children
away from the assembly area. Two capable adults are
needed for the following steps.
NOTE:
ASSEMBLY TIP
The following pages will have a picture of the
Hardware Needed along with the Quantity, Part
Number and Description. You can lay the hardware
on the picture to identify the hardware.

10
DETAIL A
23
WASHER M10
2B-6800-00
(QTY. 2)
HEX LOCK NUT M10-1.5
2B-6801-00
24
(QTY. 1)
HARDWARE NEEDED (ACTUAL SIZE)
HEX HEAD BOLT M10-1.5 X 210mm
1B-7080-00
34
(QTY. 1)
34
23
24
23
12
2. Attach lower pole (12) to lower assembly. Line up the holes in
the four tubes and lower pole and attach hardware as shown
in Detail A. Tighten hardware finger tight only.

11
12
16mm
TOOLS NEEDED
16mm
23
WASHER M10
2B-6800-00
(QTY. 4)
HEX LOCK NUT M10-1.5
2B-6801-00
24
(QTY. 2)
HARDWARE NEEDED (ACTUAL SIZE)
HEX HEAD BOLT M10-1.5 X 25mm
1B-7082-00
(QTY. 2)
36
DETAIL A
36
23
24
23
3. Finish securing lower pole (12) to lower assembly
as shown. Tighten all hardware at this time
including hardware from step 1 & 2.

12
DETAIL A
Wood
block
4. Before Inserting Axle Bushings (5) into the lower assembly Steel
Tube, align the bushings (5) so the groove goes over the tube
weld seam without touching it. See Detail A & Detail B.
5
5
DETAIL B
Rubber
Mallet
5
Steel
Tube
Tube
Weld
Seam
5. Use a wood block and Rubber Mallet to gently tap the Axle
Bushing into Steel Tube. Center Wood block onto Axle
bushing and tap on the center of the block, do not tap on
the edges of Axle bushing because it could damage it.
Steel
Tube
Side View of Steel tube
and Axle Bushing (5).
A B
C
Groove
Axle Bushing
inserted into
Steel Tube
Groove
TOOLS NEEDED
Wood Block
Rubber
Mallet
Steel
Tube
Tube Weld
Seam
NOTE
Use a wood block and Rubber Mallet to
gently tap in the Axle Bushing into Steel Tube.
NOTE: Make sure Axle Bushing
is completely into and flush to
the outside of Steel Tube.

13
6. Insert Axle (4) into lower assembly Steel tube
until both ends of the Axle stick out about the
same distance on each side.
4
Steel
Tube

14
DETAIL B
7. Slide Wheel (7) onto Axle (4). Repeat step to
install the second wheel. See Detail B.
NOTE: Inner Wheel Hub (6) and Outer wheel (8) are
pre-assembled into Wheel (7) by the factory. If
either of those parts have fallen out during
shipping re-insert parts as shown in Detail A.
87
6
7
7
DETAIL A
4
NOTE
Inner Wheel Hub (6) and Outer wheel (8) are
pre-assembled into Wheel (7) by the factory. If
either of those parts have fallen out during
shipping re-insert parts as shown in Detail A.
NOTE
Inner Wheel Hub (6) and Outer wheel (8) are
pre-assembled into Wheel (7) by the factory. If
either of those parts have fallen out during
shipping re-insert parts as shown in Detail A.
NOTE
The flat part of the
Wheels go to the
outside.

15
HARDWARE NEEDED (ACTUAL SIZE)
WASHER M10 X 30mm
2B-6795-00
10
(QTY. 1)
8. Insert Axle Rod (9), through Washer (10) and into
Wheel assembly and axle until it reaches the
other side of the Axle and wheel. Have a Second
person hold second Wheel.
NOTE
You may have to wiggle the Axle Rod (9)
up and down and side to side so it goes
through the second wheel.
DETAIL A
9
10

16
HARDWARE NEEDED (ACTUAL SIZE)
WASHER M10 X 30mm
2B-6795-00
10
(QTY. 1)
HEX NUT M10-1.5
2B-6796-00
11
(QTY. 1)
WASHER, LOCK INTERNAL-TOOTH
2B-6806-00
43
(QTY. 1)
16mm
TOOLS NEEDED
16mm
9. Secure Axle Rod (9) with Washer (10), Lock Tooth
Washer (43) and Hex Nut (11). Tighten Nut (11) until
there’s about ¼” of thread of the Axle Rod sticking
out of nut. Do not overtighten. See Detail A.
NOTE: Wheels must spin freely, there should also
be some side to side play on both wheels.
DETAIL A
11
43
10
9
Use 16mm Socket
on Nut (11).
Use 16mm
Wrench for
Axle Rod.

17
NOTE
DETAIL A
11. Carefully slide Ballast (1) over Lower Pole as shown.
42
41
10. Unscrew the Wheel cap (41) and remove, O-ring (42) is pre-attached to
Wheel cap. Fill both wheels with water until 75% full (approx. 1 gal.)
and screw Wheel cap back into the wheel with Wheel Plug key (57).
Make sure that O-ring is attached to Wheel Cap. See Detail A.
57
Use Funnel if necessary.
1
WHEEL PLUG KEY
3M-9022-00
(QTY. 1)
HARDWARE NEEDED
57
NOTE: 3/8”
Allen Wrench can
be substituted for
Wheel Plug Key.
NOTE
Kick Stand and Fill Cap
are on the same end.

18
DETAIL A
DETAIL B 17
16
15
16
18
19
12. Attach Left Brace tube (19) and Right brace Tube
(18). Match up the color coded stickers on green
the Right Brace tube and the lower pole and
match the color stickers on the Left Brace tube Red
and Lower Pole as shown in Detail A. Insert the
hardware through brace tubes, Ballast and Frame
assembly as shown in Detail B.
BRACE TUBE, RH
BRACE TUBE, LH
Lower Frame Assembly
HARDWARE NEEDED (ACTUAL SIZE)
WASHER M8
2B-6797-00
(QTY. 4)
Hex Lock Nut M8-1.25
2B-6808-00
17
(QTY. 2)
HEX HEAD BOLT M8-1.25 X 65mm
1B-7077-00
15
(QTY. 2)
18
19
16
Match Green
Stickers.
Match Red
Stickers.
( Sticker)Green
( Sticker)Red
12
NOTE: Finger Tighten only!
NOTE
FINGER TIGHTEN ONLY!
DO NOT INSERT A BOLT
INTO LINKAGES (18,19)
OR POLE (12) UNTIL
STEP 15.
NOTE

19
DETAIL A
HARDWARE NEEDED (ACTUAL SIZE)
HEX HEAD BOLT M8-1.25 X 65mm
1B-7077-00
15
Hex Lock Nut M8-1.25
2B-6808-00
17
(QTY. 2)
13. Secure ballast to lower assembly as shown in
Detail A. Finger Tighten hardware.
16
17
15
WASHER M8
2B-6797-00
(QTY. 4)
16
NOTE: If needed use your thumb to push bolt
forward (see Detail B) and then down
(see Detail C) so it goes in easier through
ballast tabs and kick stand tube.
(QTY. 2)
NOTE
FINGER TIGHTEN ONLY!
DETAIL B
DETAIL C
SIDE VIEW

20
HARDWARE NEEDED (ACTUAL SIZE)
50
50
HEX HEAD BOLT M10-1.5 X 110mm
1B-7079-00
22 (QTY. 1)
22
23
23
HEX NUT M10-1.5, WITH CAP
2B-6799-00
21
(QTY. 1)
21
WASHER M10
2B-6800-00
23
(QTY. 2)
15. Insert Bolt (22) through braces 18 &19 and through both poles as
shown. Tighten hardware finger tight only.
12
18
19
14. Position Middle pole (50) with the Warning label facing forward,
then slide Middle pole into Lower pole (12). Make sure that all
holes are aligned in both poles.
NOTE
FINGER TIGHTEN ONLY!
NOTE
warning label
should be facing
forward.
CAUTION:
PINCH POINTS! DO NOT
place your hand on any of
these three locations when
inserting the pole.