ESP MAGDUO User manual

A knowledgeof BS5839: Pt 1: 2017: Fire Detection and Alarm Systems for Buildingsis essential.
It is strongly recommended that a suitably qualified and competent person is consulted in connec on
with the Fire Alarm System design and that the en system is commissioned in accordance with the
current n onal standards and specifica ons.
Equipment Guarantee
The equipment carries no warranty unless the system is installed, commissioned and serviced in
accordance with the manual and the relevant standards by a suitably qualified and competent person
or organ on.
26-1706-01
Do not attempt to install this equipment until you have fully read and understood the manual
which can be found on our website
Access Levels and Codes
Access Level Key Operation Code Controls Enabled LED
Normal N/A N/A OFF
User YES 1111 ON
Supervisor NO 2222 SLOW FLASH
Engineer NO 3333 FAST FLASH
Quick Star t Guide
https://www.espuk.com/technical_support/product_manuals/?cat=4

The panel is fi ed with an on board USB-B connector. This is to provide communica on via a suitable USB
lead to a PC for programming of panel op ons using the
configuraon soware.
LCDcontrast may be adjusted by rota g the screw on the variable resistor, located in the upper right hand corner of the
main PCB.
Write Protect Mode:
In the OFF posi on, as shown (le ), engineering op ons may be viewed but no changes made
ON
Write Enable Mode:
If changes are to be made, this switch needs to be in the ON posi on as shown (le ).
If the switch is le ON whilst the panel is not in engineer mode a system fault will be reported.
ON
All system wiring should be installed to comply with BS 5839: and BS 7671 (wiring regula ns) and any
other standards relevant to the area or type of installa on. A cable complying with BS 5839: Pt 1: Category 1 (cables required
to operate for prolonged periods during fire cond ons) is required. This must be a 2-core 1.5mm2 screened fire resistant
cable (ie. FP200, Firetuff, Firecell, Lifeline or equivalent).
Each zone requires a separate 2-core radial circuit from the control panel to the furthest point of the zone, to a maximum of
500 metres.
The cable screen must be connectedto earth/ground at the control panel only.
The cable screen continuity must be maintained at every point of the circuit, using the terminals provided or a suitable
conne on block.
Do not use a 4-core cable as a circuit zone in and zone out, due to the possibility of data corrup on. It is essen al that two 2-
core screened cables are used if this is required.
www.fike.co.uk
1
2
3 MAGDUO
Topology & Cabling
26-1706-01

NETWORK CONNECTIONS ONLY AVAILABLE ON 4/8 ZONE PANEL TO ADD REPEATER
NET A
NET B
SCRN
NET A
NET B
MI/P+
MI/P-
SCRN
1+
1-
2+
2-
Z8+
Z8-
SCRN
Z7+
Z7-
SCRN
Z6+
Z6-
SCRN
Z5+
Z5-
SCRN
Z4+
Z4-
SCRN
Z3+
Z3-
SCRN
Z2+
Z2-
SCRN
Z1+
Z1-
SCRN
N/C
N/O
COM
N/C
N/O
COM
MO1+
MO1-
SCRN
MO2+
MO2-
SCRN
AUX+
AUX-
SCRN
BAT+
BAT-
+V IN
0V IN
EARTH
•MAX ZONE LENGTH 500M
•UP TO 32 DEVICES PER ZONE
•BUILT-IN EOL CAPABILITY IN ALL DEVICES
•DETECTORS, SOUNDERS AND MANUAL CALL POINTS TO BE INSTALLED ON THE SAME PAIR OF WIRES
•DO NOT USE A RESISTOR FOR EOL
-
+
+
-
UNUSED ZONES NEED TO
BE SWITCHED OFF
•DO NOT USE A
RESISTOR FOR
EOL USE SW1
3K3 EOL
680Ω
N/O CONTACT
N/O CONTACT
FAULT @ 30V DC 200MA MAX
10K EOL
30V DC LOAD
MAXIMUM OF 8 REPEATER PANELS
2 X 12V DC 3.2AH OR 3.4AH SEALED LEAD ACID BATTERIES
FROM PSU
FIRE @ 30V DC 200MA MAX
•DO NOT USE A
RESISTOR FOR
EOL USE SW1
26-1706-01

Technical Data
For specifications of the MAGDUO, please see the MAGDUO Manual.
Technical Support
Due tothe complexity and inherent importance of a life risk type system, training on this equipment is essential, and commissioning should
only be carried out by competent persons.
ESP’s policy is one of continual improvement and the right to change a specification at any time without notice is reserved. Whilst every care
has been taken to ensure that the contents of this document are correct at time of publication, ESP shall be under no liability whatsoever in
respect of such contents. E&OE.
www.espuk.com
Control Panel Ratings 2 Zone Panel 4 Zone Panel 8 Zone Panel
Weight (excluding ba eries) 2.25 kg 2.28 kg 2.36 kg
Mains voltage 230V AC Nominal 700mA
Opera ng voltage Nominal 24V DC (Range 21-31V DC)
Construc n V0 rated ABS
IP Ra ng IP 30
Opera ng standard BS EN54-2 & 4
Opera ng temperature 5°C to 40°C
Control Panel Fuses and Protection 2/4/8 Zone Panel
Zone output 300 mA trip polyfuse
Sounder output 300 mA trip polyfuse
Remote fire output (mon relay) 300 mA trip polyfuse
Auxiliary 24V DC supply 300 mA trip polyfuse
Mains T4A Time Delayed 20mm Ceramic
Ba ery Charger 300mA current limiter
Ba ery (reverse polarity) 3.15A F 20mm
26-1706-01