ESP EZ-WF User manual

WIREFREE VIDEO SIG AL LI K
EZ-WF
EZ-WF Manual_Layout 5 28/01/2013 11:21 Page 1

2
EZ-WF Manual_Layout 5 28/01/2013 11:21 Page 2

3
TX Transmitter module RX Receiver module 2 x12 VDC
power adapter
User manual
2 x Antenna
Contents
Table of contents
System Setup and Usage Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Locating the TX and RX modules . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation – TX module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation – RX module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pairing the TX and RX modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Multiple unit installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EZ-WF Manual_Layout 5 28/01/2013 11:21 Page 3

4
VIDEO IN
AUDIO IN
VIDEO OUT
AUDIO OUT
LOCAL MONITOR
MICROPHONE
CAMERA
POWER IN
12VDC
150m OPEN FIELD
CAMERACAMERA
1
50
O
m
N F
OPEN F
O OUT
O IN
VIDEO IN
POWER IN
O OUT
O OUT
POWER IN
12VDC12VDC
EZ-WF - Wire free digital CCTV link Syste Setup
and Usage Guide
The EZ-WF is a 2.4GHz Digital transmitter / receiver system that
creates a reliable and exceptionally easy to install wireless
communications link indoors or outdoors for video and audio.
nDynamic frequency selection 2.4000 GHz to 2.4835 GHz
nUp to 150M open field range
nStable digital signal
nIP66 rated weatherproof housings suitable for external use
n3dB omnidirectional antenna
EZ-WF Manual_Layout 5 28/01/2013 11:21 Page 4

5
EZ-WF is designed to create a wire free link for a single camera
however up to four EZ-WF units can be installed in close proximity
without interference. To gain maximum range capability the transmitter
and receiver units should be mounted within direct line of site of each
other. Both transmitter and receiver are IP66 rated and therefore
suitable for external use however all wired connections should be made
in a separate IP rated waterproof enclosure.
VIDEO 1 OUT
AUDIO 1 OUT
VIDEO 2 OUT
AUDIO 2 OUT
DVR
MONITOR
POWER IN
12VDC
OPEN FIELD
O
D
EL
N F
FIE
OPEN F
AUDIO 1 OUT
VIDEO 1 OUT
DIO 1
DEO 1
POWER IN
AUDIO 2 OUT
VIDEO 2 OUT
DVR
DIO 2 OUT
DEO 2
DVR
12VDC DVRDVR
EZ-WF Manual_Layout 5 28/01/2013 11:21 Page 5

Locating the TX and RX odules
To achieve a strong stable signal and maximum possible range carefull
thought must be made with regard to the location of the TX and RX
modules.
To achieve maximum range there should be a clear line of sight
between the TX and RX modules. Ideally when creating a link between
buildings the modules should be mounted on external walls opposite to
each other.
Mount the units as high as possible to avoid temporary blockages in
line of site transmissions such as vehicles and pedestrians.
Mount the units so that arerials are vertical at the top of the unit.
6
UP TO 150m OPEN FIELD
EZ-WF Manual_Layout 5 28/01/2013 11:21 Page 6

7
Be aware the unit requires 12vdc power which can be provided by the
included power supply unit or an alternative source rated at 12vdc @ 1amp.
Try to avoid locating the modules in close proximity to sources of
electrical equipment that may give radiated interference such as
microwaves and high voltage cables.
Video and, if available, Audio outputs from the camera and microphone
are connected directly to the TX module. Connections are also available
for a local monitor or test monitor during set up.
Installation – TX odule
1. Screw an antenna onto the connector
at the top of the TX module.
2. Mount the TX module using appropriate fasteners to a solid mounting
surface.
3. Complete the connections to the video and/or audio source to the
video and audio in. A video and audio out is also provided to connect to
a local monitor or test monitor.
ANTENNA CONNECTOR
RCA connector AUDIO IN
AUDIO OUT
BNC connector VIDEO IN
VIDEO OUT
POWER
EZ-WF Manual_Layout 5 28/01/2013 11:21 Page 7

8
Installation – RX odule
4. Screw an antenna onto the connector at the top of the RX module.
5. Mount the TX module using appropriate fasteners to a solid
mounting surface.
6. Complete the connections between the two video and audio outputs
to the monitors or recording devices as required.
Pairing the TX and RX odules
The TX and RX modules of each EZ-WF set are factory configured to pair
only with each other. The pairing will occur automatically after
approximately 30 seconds after powering both the TX and RX units as
long as they are within range. If pairing is lost it can be re-established by
powering off, then powering on one or both of the modules. After
powering off either module, wait 10 seconds before powering it on again.
RCA connector AUDIO OUT 1
AUDIO OUT 2
BNC connector VIDEO OUT 1
VIDEO OUT 2
POWER
EZ-WF Manual_Layout 5 28/01/2013 11:22 Page 8

9
Multiple unit installations
Up to four sets of EZ-WF can be located within range of each other
however please ensure a minimum distance of 30cm between units
from different pairs.
During commissioning initially power each pair separately allowing
sufficient time for auto pairing . Check pairing has been achieved (Video
and audio if required) before powering second and subsequent pairs.
NOTE lf multiple systems are setup in the same vicinity and pairing is
lost between one or more TX/RX module pairs, power off the modules
of the pairs that failed, then power on each pair one at a time and allow
it to synchronize before powering on another pair.
Troubleshooting
PROBLEM POSSIBLE SOLUTIO S
o video or audio • Check power and A/V Cable connections.
• Verify that the TX and RX module are powered on.
• Verify that video and audio source signals are
applied to the TX module.
• Verify that the recording/video monitoring
equipment is functioning properly.
Interference • Adjust the orientation of the antennas on the
in video TX and RX modules.
• Move the equipment away from devices that emit
high radiation, such as microwave ovens, wireless
phones, etc.
EZ-WF Manual_Layout 5 28/01/2013 11:22 Page 9

10
Technical specification - Syste
Transmission channels 80 channels, auto selected
Video bit rate Up to 12Mbps
ID codes Up to 4 Million
Video resolution 720 x 480 @ 30fps
Operational range 150m open field
Technical specification - TX Trans itter odule
Operating frequency 2.4000 GHz – 2.4835 GHz
Transmit power 100 Mw (MAXIMUM)
Modulation 16 QAM / QPSK / BPSK
Video input level 1 ± 0.2 Vp-p @ 75 Ω
Audio input level 1 ± 0.2 Vp-p @ 600 Ω
Antenna Omnidirectional
Power consumption 1.9 W
Power adapter 12 VDC / 1A
Dimensions (W x D x H) 159.5mm x 136.4mm x 34.8mm
without antenna and drop cable
Weight 19 oz (538 g)
Technical specification - RX Receiver odule
Operating frequency 2.4000 GHz – 2.4835 GHz
Receiver sensitivity -85 dbm minimum
Video output level 1 ± 0.2 Vp-p @ 75 Ω
Audio output level 1 ± 0.2 Vp-p @ 600 Ω
Antenna Omnidirectional
Power consumption 1.9 W
Power adapter 12 VDC / 1A
Dimensions (W x D x H) 159.5mm x 136.4mm x 34.8mm
without antenna and drop cable
Weight 19 oz (538 g)
EZ-WF Manual_Layout 5 28/01/2013 11:22 Page 10