ESP MAGPRO-HD1 User manual

Installation Instructions
MAGPRO-HD1
Intelligent analogue addressable fire
alarm heat detector
Distributor: Elite Security Products Ltd,
Unit 7 Target Park, Shawbank Road
Lakeside, Redditch B98 8YN, UK
http://www.espuk.com
Manufacturer: Teletek Electronics JSC
14A Srebarna Str, 1407 Sofia, Bulgaria
EN 54-5: 2000/ A1: 2002,
Detector Class A1/R, A2/S, B/S
DoP No: 038
Tested by EVPU: N.B.1293
1293 15
ATTENTION: Read carefully this installation instruction before installing the device.
This manual is subject to change without notice errors and omissions accepted.
>30cm >30cm
<7m - MAGPRO-HSD1
<5m
-
MAGPRO-SD1
MAGPRO-HD1,
18020163, RevB, 02/ 2015
GENERAL DESCRIPTION:
MAGPRO-HD1 is аn addressable temperature detector designed for use with ESP MAGPRO fire alarm panels. The detector is powered from
the panel and can be controlled via its communication protocol.
The MAGPRO-HD1 is compatible with detector base MAGPRO-DB.
INSTALLATION
1. Select a suitable position for installation. Note: Do not install the detector near to natural heat sources, e.g. above cookers, ovens or fire
places.
2. Mount the detector base to the required surface with suitable fixings.
3. Connect the detector base to the fire panel using the wiring diagram.
ATTENTION: Disconnect the loop power before installing the detector!
4. To activate the anti tamper lock option on the detector base carefully remove the small tooth shown in Fig2 using short nose snips.
5. To locate the detector onto the base align the line mark on the detector with the short line mark on the detector base. Rotate the detector
clockwise until the short line mark on the detector coincides with the long mark on the base and a “click” is heard.
6. If removal of the detector is required after the detectors anti tamper lock function has been selected a small flat blade screwdriver should be
inserted into the aperture on the side of the detector base. Lightly press with the screwdriver at the same time as rotating the detector head in
a counter-clockwise direction.
TECHNICAL SPECIFICATIONS
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . . . 15 - 32VDC (Nom. 27VDC)
Consumption in quiescent state, no communication . . < 130μA@27VDC
Consumption in quiescent state, with communication .< 180μA@27VDC
Consumption in alarm state, with communication . . . . 6.5mA
Class, selectable from the control panel ...........A1/R, A2/S, B/S
Protected area (in accordance with EN54-5) ........up 35m²
Installation height (in accordance with EN54-5) ......up 3,5m
Output in alarm state at terminal RI (terminals 4/ 1)...7.5 mA (max)/ 7.5V
2 2
Wire Gauge for terminals . . . . . . . . . . . . . . . . . . . . . . . 0.4mm ё 2.0mm
Relative humidity resistance.....................(93 ± 3)% @ 40°C
Dimensions (incl. base) ........................ø103mm, h 42mm
Essential characteristics Performance
Performance under fire conditions Pass
Operational reliability Pass
Durability of operational reliability and response delay: temperature resistance Pass
Durability of operational reliability: humidity resistance Pass
Durability of operational reliability: shock and vibration resistance Pass
Durability of operational reliability: corrosion resistance Pass
Durability of operational reliability: resistance to ingress Pass
IP30
-10°C ÷ +60°C
Installation
~110g
Indoor
Outdoor
!
Without base

7
5
6 LED Indication
4Connection Diagram
!Test and Maintenance
TESTING THE DETECTOR
1. Apply power to the detector.
2. Wait for 30 sec.
3. Introduce artificially generated heat directly beneath
the detector. Within 8 sec the detector will enter into fire
condition. Both LEDs will illuminate.
4. Power off the detector for 2 sec minimum. After
resetting the detector will enter into duty mode and both
LEDs will extinguish.
SERVICE MAINTENANCE
1. Inspection for visible physical damage - weekly.
2. Operational test in real conditions - monthly.
3. Check and clean dust contamination - six months.
4. Check and clean base and head contacts and
connections - annually.
CLEANING AND MAINTENANCE
1. Remove the detector from its base.
2. Remove the inner protective cover - press the four
clips (1) with a plain screwdriver gently down to unlock
the cover from the detector’s body.
3. Dismount the PCB from the supporting clips (2).
4. Clean the chamber.
5. Mount the PCB back to the detector’s body - as a
reference point use the side with a cut-out (3). Rotate the
PCB until the cut-out coincides with the pin on the inner
part from the detector body. Gently press the PCB down
to fix in place.
6. Mount the inner protective cover - the mark with a
rectangular shape (4) fits with the channel at the inner
side of the detector’s body and the contact plates on the
PCB coincide with the four openings on the protective
cover. Press gently down until a click is heard.
7. Mount the detector back to its base and test for correct
operation and LED indication.
!Maintenance
3
12
Base MAGPRO-DB Address Programming
Down
Right
Up
Modify
Esc
Enter
MAGPRO
PROG
You may also program the
address directly from the
fire panel.
Blinking 10 sec OK
Light on
Light off
Light on
Light off
1. Blinking is enabled
2. Blinking is disabled
The LED indication can be enabled/ disabled
from the control panel.
Fire Panel
Earth (Earth point)
RI
(Remote
indicator)
+Loop
-Loop
-Loop (Negative Loop Wire)
+Loop (Positive Loop Wire)