ESP SANGAMO CHOICE RSTATWIFI User manual

CHOICE RSTATWIFI
OPERATING INSTRUCTION
www.espuk.com
Elite Security Products
Unit 7, Target Park,
Shawbank Road, Lakeside,
Redditch B98 8YN
Tel: [phone]
Fax: [phone]
www.espuk.com • [email protected]
Elite Security Products Ireland
18 Corrig Road,
Sandyford Ind. Estate,
Dublin D18 WV79, Ireland
Tel: [phone]
Fax: [phone]
www.espi.ie • [email protected]
The latest ESP manuals
can be found Online:

The CHOICE RSTATWIFI is designed to be used with electric, gas or oil heating systems.
The receiver is to be installed nearby the boiler/furnace to operate the call for heat. The thermostat is to
be installed in the position best suited to monitor the environment’s temperature.
Product introduction
Quick installation and test
RF code match
Link APP
Thermostat Operation
Thermostat Programming
01-07
08-14
15-17
18-25
26-34
Contents
Product introduction
01
35-37

Specifications
Power source :
IP Rating:IP21
Temperature setting range :5℃~35℃
：0.5 ℃Tem perature setting accuracy
5℃~50℃Temperature display range:
Temperature accuracy :0.1℃
Operation temperature range:0~50℃
Sh ipping & storage temperature: -10℃～60℃
Frequency:868MHZ(Bidirectional FSK)
Wireless transmit range:100M
WiFi Communication protocol :TCP/IP, MQTT
WiFi frequency :2.412GHZ-2.484GHZ
4 AAA batteries (Wi-Fi unavailable)
AC 100-240V 50/60Hz
Power source：100-240VAC 50/60HZ
IP Rating：IP21
Operation temperature range：0~50℃
Shipping & storage temperature：-10℃～60℃
Output：Relay Load 250v/16A ,standard 16A,
f Volt-Free switch systems (0.5A)
Frequency：868MHZ (Bidirectional FSK)
Wireless transmit range：100M
Thermostat Receiver
02 03

124mm
88mm
21mm
Wake-up
button
Thermostat’s appearance
Menu button
Time setting
button
Power button
UP button
DOWN button
Thermostat power mode
04 05
1
NO.
2
NO.
3
NO.
Terminal
position
1. Take off the safety cover when wiring
Wire electric power
4 AAA batteries
Micro USB
Use phone charger to access
the USB connector
Put battery into battery
compartment
Open back cover plate
2. Cover the protective cap
after the terminals connected
neutral and live wire
No difference
between neutral
and live wire here
If the thermostat is only powered with batteries, the Wi-Fi function will be
disabled. But will function as a conventional wirefree thermostat. In addition
to the batteries, for Wi-Fi function the thermostat requires permanent power
via mains supply (NO.2) or USB (NO.3).

86mm
86mm
50mm
24mm
Matching Code Indicator
•Flashing Amber: Code
matching registration
activated
•Steady Amber:
Receiver is matched
Power LED Indicator
•Steady Red: Power
supply is on
•Steady Green: Manual
call for heat activated
Call for Heat Indicator
•Steady Green: Call for
heat activated
Power button
Receiver appearance Receiver indicator status
Power indicator
Output indicator
Status indicator
06 07

The unit is designed to be used with electric, gas or oil heating systems.
The receiver is to be installed nearby the boiler/furnace to operate the call for heat. The thermostat is
to be installed in the position best suited to monitor the environment’s temperature.
·The open field distance between the receiver and thermostat is 100meters, this is an RF signal.
·If the thermostat has been fitted with a permanent mains supply, the user can control the room
temperature via mobile phone APP, this is via a Wi-Fi signal to the network’s router.
In both cases please ensure that the signal is not compromised prior to installation. Types of building
materials, potential signal dead zones and the working environment needs to be assessed.
If Wi-Fi signal is a possible issue, one solution is the numerous Wi-Fi signal enhancing devices on the
market to improve a network’s performance.
As with all Wi-Fi, software and hardware depended devices, ESP are unable to guarantee that every
device will be compatible with the supplied product and software.
Specific models of phone, tablet or other devices, the hardware it contains, the service
provider, the types of data services offered and variations in version numbers can affect the
performance.
Quick installation and test
Thermostat’s
position Router’s position
1m
1.5m
≤50m
Receiver
position
30cm
wall-hanging
boiler
When installing, the distance between router and thermostat should within 50M
(adjust the distance according to actual network cover )
installation position Note
08 09

Thermostat Mounting Installation Thermostat table stand
Desk stand
Open the stand
1 2
4
3
put the back board on
the installation boxput the screw into the
hole and screw down
Cover the panelCompleting installation
10 11

2
Checking the Power Supply to the Receiver
When the receiver’s supply and connections to the boiler have been established, press the receiver’s power
button once and the red LED will indicate the supply is present.
Checking the Receiver’s Boiler Connections
Press the power button once more so that no status LEDs are active, press and hold the power button until the
2 status LEDs display green (Approx. 10secs).
This process will manually trigger the switch to the boiler. If the boiler does not trigger please review the
connections and refer to the boiler’s manual or support.
After installation is complete and a circumstance arises where the heating needs to be triggered without the
thermostat, the receiver is able to manually trigger the boiler using the above process.
The power
supply
Maximum load:16A
L1
L
N
N1
NC
NO COM
Max：250VAC/0.5A
wiring:
N
L
put the wire into the terminal
and use the straight screwdriver
to screw down
Receiver installation
Open receiver's panel
1
Open
Buckle
Rotate
(Figture 1)
(Figture 2 )
Pry the Buckle with a flattened screwdriver
Power wire
Test
Receiver Wiring Diagram
Boiler
Power:100-240VAC 50/60HZ
12 13
Refer to the boiler’s manual or support for the appropriate connections.
Connection A) For systems requiring a volt-free switch Connection B) For systems that require a Live switch

To start registration mode; long press the power button on the
thermostat and on the receiver, press the power button until there are
no status LEDs.
Manual Set
Mode
Anti-freezing
Call for Heat
Schedule Mode
Hotspot Mode

Yellow light
flashing
match success
indicate enter code

Li nk APP
Download
1
4
Search :
SANGAMO CHOICE
2
3
GETGET
Insert email
address
18 19
SANGAMO
CHOICE
User Name
REGISTER
REGISTER

*
G
Enter the registered email address
LOGIN

SEND
Select WIFI
6
Add the thermostat in IOS
Return to phone’s
setting
1
Settings
Click “Wireless Local
Area Networks”
2
WLAN
Choose the SSID
3Reopen APP 4
Click ‘+’
Click SEN
5
22 23

Add the thermostat in Android
13
2
Click CONFIG
4
Click ‘+’
Choose the SSID
( )
When succe ssful with configuration, click try
now, then enter the overview interface
5
24 25

Temperature Setting
Press 、 to adjust the temperature
*Reminder
Thermostat operation
When the set temperature is higher
than the room temperature, the
thermostat activates the call for heat
26 27
button
In running mode, press enter time
setting mode
" "
" "
、
All programming can be completed on the
.
If the thermostat is powered down, then all
settings will be retained including network
settings

Menu
button
The programming menu
has been entered one the 0
is displayed
Programming
1. Select programming rules
Setting for two time periods in a
week. Monday to Friday and
Saturday to Sunday.
2. Select programming
periods
Setting for three time periods in a week. Monday to Friday, Saturday and Sunday.
5+2
programming
Day
programming
Day
5+1+1
7 individual
programming
Day
Setting the seven time period
in a week, setting the
PERIODS
4Programming with 4
temperature periods
within a day PERIODS
6Programming with 6
temperature periods
Enter the thermostat programming menu

Menu
button
Select the programming
period
a. Press " "to toggle screen, until
see the " "
3
b.Press " "
to choose.
After setting, press " "save and exit.
4
Select the programming mode
Non programmable
2
a. After entering the
implied parameters,
continue to press " "
to toggle screen, until
see the " ".
Programming – set the week programming
Enter programming settings:
1
b. Press " "
to choose.
：4 periods
The default is 4 periods
：6 periods
5+2 programmable
5+1+1 programmable
7 days programmable
In running mode, hold menu button more than 5 seconds." "
30 31

Short press " ",switch the time and temperature of the week and period. When the
icon is flashing, press" 、 "to choose.
2
week
a. The week icon
flashes
period
b. Set the time
period
time
c. Set the time
of the period
temperature
d. Set the
temperature of the period
The icon" "indicates the start and the icon" "indicates the end., the start time and
temperature are set for each period of the week, If you are not at home, the middle of
the two periods do not need to setting.
3
After setting, press" "save and exit.
4
Wake
up
REMIND: If you choose 4 periods programming, the noon time period will not be displayed.
Outdoor Back
home
Back
home Sleep
Morning NoonNoon AfternoonMorning Evening
32 33
Outdoor

Configuration menu setting
Thermostat configuration
Remind
temporary
holding mode
permanent
holding mode
2 The user can permanently override
the programed set temperature by using
the 'Up' and 'Down' arrows and pressing
the 'Menu' button. To reinstate the
programming mode, the 'Menu button is
pressed again.
The user can temporarily override
the programed set temperature by
using the 'Up' and 'Down' arrows. until
the next programmed event occurs.
13The thermostat has an automatic frost
protection feature. As default this is set to
5°C, if this temperature is reached the
thermostat will action a call for heat.
Menu
button
When this interface
appears ，
mean by enter the implicit
parameters
In shutdown mode, hold menu button more than 5 seconds
1
34 35

2
3
Enter the first of configuration menu setting. Press " "to adjust parameters. Press
" "button again enter next item, press " "button confirm and return to shutdown mode.
If no button is pressed within 10 seconds, the thermostat will automatically exit the
configuration menu setting and back to shutdown mode.
In the menu setting, press the menu button for 3 seconds until DEF flashes 3 times. The
thermostat will return to factory default mode.
4
More than 3 seconds
Flashes 3 times
Menu
button
Thermostat configuration menu layout
-4 — +4
Temperature
correction value
24℃—35℃
Temperature
setting upper limit
5℃—20℃
Temperature
setting lower limit
0/2/3/7
Programming
mode selection
0：Non programmable 2 ：5+2 program
3：5+1+1 program
7：7 days program
4/6
Programming
period selection 6: 6 time zones ；4: 4 time zones ；
10/15/20
Display time
Antifreeze protection
function On：Frost protection on ；OF ：Frost protection o
On/ OF
Press
buttons Descriptions
Press 、
to select
Displayed
0.5℃~5℃
Control accuracy
Start heating conditions:
When setting temperature ≤room temperature-0.5 ℃, stop heating
When setting temperature ≥room temperature reduction db parameters
start heating
Settings
36 37