Essence Smartcare Care@Home MDsense User manual

RESET
Button
Control Panel
Press RESET. The control panel
responds with a voice message
14
Multi-dimensional fall sensor
Care@Home™
MDsense
Getting Started
smartcare
11 Pull the strip down. Press the
MDsense against the wall
Walk in front of the MDsense. The
LED flashes quickly
Lie on the floor. Remain still while
the LED is solid red. Stand up
when the LED flashes slowly
13
12
Place the MDsense near a corner
with the strip touching the wall
9
10 Slide the MDsense into the corner.
The glue sticks
Installing and Testing the MDsense Using an advanced fall detection
algorithm with state-of-the-art
technology, this wireless fall sensor does
not require the resident to wear any
detection device. When integrated with
Care@Home™, the MDsense can detect
a resident’s fall regardless of whether the
room is brightly lit or completely dark.
The MDsense is the perfect fall sensor
for any home or retirement facility.
Legal notice:
http://www.essence-grp.com/html/concerning_documents.html
© 2020 All rights reserved to Essence SmartCare Ltd.
www.essencesmartcare.com • [e-mail]
ESUG05202 Rev. 1.0
smartcare
MD sense

Where to Install Installing and Testing the MDsense
Remove the lens covering
Press here
Remove the battery compartment
1
2 4
Insert the batteries
Press the PAIRING button on
the Care@Home™ control panel
PAIRING
Button
Control Panel
3
Room with maximum size of 5 x 5 m
(16.4 x 16.4 ft.)
In the corner
Height of
2.1 m (6.9 ft.)
Clean, dry smooth surface
Within 700 m (2,297 ft.), open air,
of the control panel
Avoid
Near heater or air
conditioner
In front of a
mirror
Moving objectsObscured
Replace the battery compartment.
The control panel responds with a
voice message
6
5
Press the PAIRING button on the
Care@Home™ control panel twice.
The control panel responds with a
voice message
PAIRING
Button
Control Panel
7
8Peel off the short protective strip
Standing at the installation location,
pull out the socket cover. The LED
lights. The control panel responds
with a voice message. Replace the
socket cover or insert pull cord or
power cord
Peel off

Where to Install Installing and Testing the MDsense
Remove the lens covering
Press here
Remove the battery compartment
1
2 4
Insert the batteries
Press the PAIRING button on
the Care@Home™ control panel
PAIRING
Button
Control Panel
3
Room with maximum size of 5 x 5 m
(16.4 x 16.4 ft.)
In the corner
Height of
2.1 m (6.9 ft.)
Clean, dry smooth surface
Within 700 m (2,297 ft.), open air,
of the control panel
Avoid
Near heater or air
conditioner
In front of a
mirror
Moving objectsObscured
Replace the battery compartment.
The control panel responds with a
voice message
6
5
Press the PAIRING button on the
Care@Home™ control panel twice.
The control panel responds with a
voice message
PAIRING
Button
Control Panel
7
8Peel off the short protective strip
Standing at the installation location,
pull out the socket cover. The LED
lights. The control panel responds
with a voice message. Replace the
socket cover or insert pull cord or
power cord
Peel off

Where to Install Installing and Testing the MDsense
Remove the lens covering
Press here
Remove the battery compartment
1
2 4
Insert the batteries
Press the PAIRING button on
the Care@Home™ control panel
PAIRING
Button
Control Panel
3
Room with maximum size of 5 x 5 m
(16.4 x 16.4 ft.)
In the corner
Height of
2.1 m (6.9 ft.)
Clean, dry smooth surface
Within 700 m (2,297 ft.), open air,
of the control panel
Avoid
Near heater or air
conditioner
In front of a
mirror
Moving objectsObscured
Replace the battery compartment.
The control panel responds with a
voice message
6
5
Press the PAIRING button on the
Care@Home™ control panel twice.
The control panel responds with a
voice message
PAIRING
Button
Control Panel
7
8Peel off the short protective strip
Standing at the installation location,
pull out the socket cover. The LED
lights. The control panel responds
with a voice message. Replace the
socket cover or insert pull cord or
power cord
Peel off

Where to Install Installing and Testing the MDsense
Remove the lens covering
Press here
Remove the battery compartment
1
2 4
Insert the batteries
Press the PAIRING button on
the Care@Home™ control panel
PAIRING
Button
Control Panel
3
Room with maximum size of 5 x 5 m
(16.4 x 16.4 ft.)
In the corner
Height of
2.1 m (6.9 ft.)
Clean, dry smooth surface
Within 700 m (2,297 ft.), open air,
of the control panel
Avoid
Near heater or air
conditioner
In front of a
mirror
Moving objectsObscured
Replace the battery compartment.
The control panel responds with a
voice message
6
5
Press the PAIRING button on the
Care@Home™ control panel twice.
The control panel responds with a
voice message
PAIRING
Button
Control Panel
7
8Peel off the short protective strip
Standing at the installation location,
pull out the socket cover. The LED
lights. The control panel responds
with a voice message. Replace the
socket cover or insert pull cord or
power cord
Peel off

Where to Install Installing and Testing the MDsense
Remove the lens covering
Press here
Remove the battery compartment
1
2 4
Insert the batteries
Press the PAIRING button on
the Care@Home™ control panel
PAIRING
Button
Control Panel
3
Room with maximum size of 5 x 5 m
(16.4 x 16.4 ft.)
In the corner
Height of
2.1 m (6.9 ft.)
Clean, dry smooth surface
Within 700 m (2,297 ft.), open air,
of the control panel
Avoid
Near heater or air
conditioner
In front of a
mirror
Moving objectsObscured
Replace the battery compartment.
The control panel responds with a
voice message
6
5
Press the PAIRING button on the
Care@Home™ control panel twice.
The control panel responds with a
voice message
PAIRING
Button
Control Panel
7
8Peel off the short protective strip
Standing at the installation location,
pull out the socket cover. The LED
lights. The control panel responds
with a voice message. Replace the
socket cover or insert pull cord or
power cord
Peel off

Where to Install Installing and Testing the MDsense
Remove the lens covering
Press here
Remove the battery compartment
1
2 4
Insert the batteries
Press the PAIRING button on
the Care@Home™ control panel
PAIRING
Button
Control Panel
3
Room with maximum size of 5 x 5 m
(16.4 x 16.4 ft.)
In the corner
Height of
2.1 m (6.9 ft.)
Clean, dry smooth surface
Within 700 m (2,297 ft.), open air,
of the control panel
Avoid
Near heater or air
conditioner
In front of a
mirror
Moving objectsObscured
Replace the battery compartment.
The control panel responds with a
voice message
6
5
Press the PAIRING button on the
Care@Home™ control panel twice.
The control panel responds with a
voice message
PAIRING
Button
Control Panel
7
8Peel off the short protective strip
Standing at the installation location,
pull out the socket cover. The LED
lights. The control panel responds
with a voice message. Replace the
socket cover or insert pull cord or
power cord
Peel off

RESET
Button
Control Panel
Press RESET. The control panel
responds with a voice message
14
Multi-dimensional fall sensor
Care@Home™
MDsense
Getting Started
smartcare
11 Pull the strip down. Press the
MDsense against the wall
Walk in front of the MDsense. The
LED flashes quickly
Lie on the floor. Remain still while
the LED is solid red. Stand up
when the LED flashes slowly
13
12
Place the MDsense near a corner
with the strip touching the wall
9
10 Slide the MDsense into the corner.
The glue sticks
Installing and Testing the MDsense Using an advanced fall detection
algorithm with state-of-the-art
technology, this wireless fall sensor does
not require the resident to wear any
detection device. When integrated with
Care@Home™, the MDsense can detect
a resident’s fall regardless of whether the
room is brightly lit or completely dark.
The MDsense is the perfect fall sensor
for any home or retirement facility.
Legal notice:
http://www.essence-grp.com/html/concerning_documents.html
© 2020 All rights reserved to Essence SmartCare Ltd.
www.essencesmartcare.com • [e-mail]
ESUG05202 Rev. 1.0

RESET
Button
Control Panel
Press RESET. The control panel
responds with a voice message
14
Multi-dimensional fall sensor
Care@Home™
MDsense
Getting Started
smartcare
11 Pull the strip down. Press the
MDsense against the wall
Walk in front of the MDsense. The
LED flashes quickly
Lie on the floor. Remain still while
the LED is solid red. Stand up
when the LED flashes slowly
13
12
Place the MDsense near a corner
with the strip touching the wall
9
10 Slide the MDsense into the corner.
The glue sticks
Installing and Testing the MDsense Using an advanced fall detection
algorithm with state-of-the-art
technology, this wireless fall sensor does
not require the resident to wear any
detection device. When integrated with
Care@Home™, the MDsense can detect
a resident’s fall regardless of whether the
room is brightly lit or completely dark.
The MDsense is the perfect fall sensor
for any home or retirement facility.
Legal notice:
http://www.essence-grp.com/html/concerning_documents.html
© 2020 All rights reserved to Essence SmartCare Ltd.
www.essencesmartcare.com • [e-mail]
ESUG05202 Rev. 1.0

RESET
Button
Control Panel
Press RESET. The control panel
responds with a voice message
14
Multi-dimensional fall sensor
Care@Home™
MDsense
Getting Started
smartcare
11 Pull the strip down. Press the
MDsense against the wall
Walk in front of the MDsense. The
LED flashes quickly
Lie on the floor. Remain still while
the LED is solid red. Stand up
when the LED flashes slowly
13
12
Place the MDsense near a corner
with the strip touching the wall
9
10 Slide the MDsense into the corner.
The glue sticks
Installing and Testing the MDsense Using an advanced fall detection
algorithm with state-of-the-art
technology, this wireless fall sensor does
not require the resident to wear any
detection device. When integrated with
Care@Home™, the MDsense can detect
a resident’s fall regardless of whether the
room is brightly lit or completely dark.
The MDsense is the perfect fall sensor
for any home or retirement facility.
Legal notice:
http://www.essence-grp.com/html/concerning_documents.html
© 2020 All rights reserved to Essence SmartCare Ltd.
www.essencesmartcare.com • [e-mail]
ESUG05202 Rev. 1.0

RESET
Button
Control Panel
Press RESET. The control panel
responds with a voice message
14
Multi-dimensional fall sensor
Care@Home™
MDsense
Getting Started
smartcare
11 Pull the strip down. Press the
MDsense against the wall
Walk in front of the MDsense. The
LED flashes quickly
Lie on the floor. Remain still while
the LED is solid red. Stand up
when the LED flashes slowly
13
12
Place the MDsense near a corner
with the strip touching the wall
9
10 Slide the MDsense into the corner.
The glue sticks
Installing and Testing the MDsense Using an advanced fall detection
algorithm with state-of-the-art
technology, this wireless fall sensor does
not require the resident to wear any
detection device. When integrated with
Care@Home™, the MDsense can detect
a resident’s fall regardless of whether the
room is brightly lit or completely dark.
The MDsense is the perfect fall sensor
for any home or retirement facility.
Legal notice:
http://www.essence-grp.com/html/concerning_documents.html
© 2020 All rights reserved to Essence SmartCare Ltd.
www.essencesmartcare.com • [e-mail]
ESUG05202 Rev. 1.0

RESET
Button
Control Panel
Press RESET. The control panel
responds with a voice message
14
Multi-dimensional fall sensor
Care@Home™
MDsense
Getting Started
smartcare
11 Pull the strip down. Press the
MDsense against the wall
Walk in front of the MDsense. The
LED flashes quickly
Lie on the floor. Remain still while
the LED is solid red. Stand up
when the LED flashes slowly
13
12
Place the MDsense near a corner
with the strip touching the wall
9
10 Slide the MDsense into the corner.
The glue sticks
Installing and Testing the MDsense Using an advanced fall detection
algorithm with state-of-the-art
technology, this wireless fall sensor does
not require the resident to wear any
detection device. When integrated with
Care@Home™, the MDsense can detect
a resident’s fall regardless of whether the
room is brightly lit or completely dark.
The MDsense is the perfect fall sensor
for any home or retirement facility.
Legal notice:
http://www.essence-grp.com/html/concerning_documents.html
© 2020 All rights reserved to Essence SmartCare Ltd.
www.essencesmartcare.com • [e-mail]
ESUG05202 Rev. 1.0