eSSL eBS-5030A User manual

www.esslsecurity.com
USER MANUAL
eBS-5030A

[键入文字]
ImportantSafe guards andWarnings
Safety Precautions
 Before using the Machine, operators must be trained with radiation protection
knowledge according to local laws and regulations, and have basic skills in using
the Machine.
 Before the Machine is supplied with power, make sure that the power supply voltage
meets requirements and the power source is properly grounded. Do not allow other
large devices to share the same power source.
 If the device becomes defective and components need to be replaced,
contact the manufacturer or follow the instructions of a professional.
 Contact the manufacturer immediately if components become damaged, such as
external cables, the conveyor belt, lead curtains, and indicators.
 Do not leave the Machine unattended when it is powered on.
 Do not put any living body parts or living animals into the tunnel when the
Machine is operating.
 Do not allow liquids to flow into the Machine while it is working. Turn off the
Machine immediately if any liquids spill on it.
 Keep the Machine away from dust and debris if it will not be used for a long period
of time.
 Regularly perform maintenance on the Machine. For example, check lead curtains
and clean the conveyor belt and the device’s surface.
X-ray Protection
The Machine is a micro dosage security inspection device. To ensure the safety of
operators and inspectors:
 X-ray is only generated when the Machine is powered on and the control switch is
turned on.
 To prevent X-ray leakage, the cabinet and collimator are covered with lead boards,
and the tunnel entry and exit are designed with two-layer lead curtains.
 In case of an emergency, operators can press the emergency stop button to stop the
conveyor belt and X-ray source.

1 Overview
The Machine inspects the baggage and items by using X-ray’s penetrability without
opening them. It adopts digital image processing and computer image display
technologies, and has a built-in semiconductor detector. These attributes come together
to make an efficient, reliable and high- quality image processing system.
This manual introduces the base functions of the Machine and provides guidance on
operating and maintaining the Machine. Read this manual before you install and use the
Machine.
2 SafetyInstructions
Before operating the Machine, you need to learn the meaning and location of the
safety warning signs on the Machine.
Table 2-1 Warning sign
Sign Meaning Location
Tunnel entrance Head of the tunnel entrance
Film safety Entrance or exit of the tunnel
Dangerous ionizing radiation Entrance or exit of the tunnel
Baggage incorrectly placed Entrance or exit of the tunnel
Baggage correctly placed Entrance or exit of the tunnel
Indicates power status Under the power indicator
Emergency stop Under the emergency stop button
Indicates X-ray status Under the X-ray indicator

[键入文字]
3 Structure
The Machine consists of an inspection tunnel and a tray.
The figure is for reference only. Slight differences might be found between the model and
the actual product.
Figure 3-1 Model
Table 3-1 Structure
No. Description
1
The inspection tunnel. Items on the conveyor belt that are in the tunnel are scanned and
then images are generated.
2 The tray that receives the items after inspection. Normally the tray is installed at the exit of
the tunnel.
4 Power-On and Startup
4.1 Preparation
When you receive the Machine, check the wooden box. If the package has any
abnormalities, contact the manufacturer immediately. Afterwards, open the wooden box
and remove the foam from inside the package. Then you can:
 Check the operating desk.
Connect the cables of the operating desk by following the provided manual and set up the receiving
tray. For the Machine without an operating desk, connect the monitor, mouse, and keyboard.
 Check the main power.

Make sure that it is functioning normally at 220 V and the power source is properly grounded.
 Check the emergency stop button.
The button is not pressed down by default. If it is pressed, rotate the button clockwise to return
theoriginalstate.
 Check the leadcurtains.
Make sure the lead curtains hang normally. Contact the manufacturer if the lead curtain
is drops down.
 Remove items from the tunnel.
4.2 Power-On and Startup
Table 4-1 Components
No.
Image
Name
Function
1 Power plug Supply power.
2 Key switch Turn on and turn off the Machine.
3 Start button Start the Machine.
4 Emergency stop button
Immediately stop the X-ray source and
conveyor belt if an emergency occurs.
5 Indicator
 Green: Power indicator.
 Red: X-ray indicator.
Hardware Operation
Step 1 Connect the triangle plug to the socket.
Step 2 Turnon the Machine. Insert the key into the key switch and rotate it
clockwise.
Step 3 Start the Machine by pressing the start button, and then the power indicator
will turn on.
After the Machine starts normally, it goes to the operation interface.
Software Operation
Step 1 Turn on the software system, and then the self-check starts. A prompt box will
appear reminding you that the calibration is in progress. The X-ray indicator is
on during the calibration and will switch off after the calibration.

[键入文字]
Normally the calibration lasts 3 to 5 seconds.
Step 2 Click to run the roller.
Step 3 Place items at the entrance of the tunnel, and scanned images will be displayed
on the system interface as they pass through the tunnel.
Step 4 Turn off the software system.
1) Click to stop the roller, and then click to go to the
homepage.
2) Click Shutdown and then in the prompt box, click Yes. The system will
turn off within 60 seconds. After that, power to the device will be cut off
and the power indicator will switch off.
4.3 Working Status
 Turned off: The Machine is not on and the power indicator is off.
 Stopped: The Machine is on and the power indicator is on, but the roller is not
running.
 Running: The Machine is on, the power indicator is on, and the electric roller is
running.
 Scanning: The Machine is on, and both the power and X-ray indicators are on.
To extend the device service life, put the Machine in the stopped state if no items were
inspected for more than 30 minutes after startup. You can also install an automatic
sensor for convenient management.
5 Software System Operation
5.1 System Main Interface
The scanned images are displayed in the center of the main interface. As items pass
through the tunnel on the conveyor belt, the scanned images appear on the interface,
scrolling across it. The area under the scanned images can be divided into three sections.
Figure 5-1 System main interface

Table 5- 1 Area
No.
Description
1 Device information area
2 Device operating area
3 Image processing functions area
5.2 Device Information Area
Figure 5- 2 Device information
 : Displays the connection status of the detection card. The icon is
highlighted when the connection is normal.
 : The icon is highlighted when IR is covering an item.
 : The icon is highlighted when the X-ray source is turned on.
 : Displays the login role, such as operator, engineer, and administrator.
 : Displays the number of scanned baggage.
 : Displays the current device status.
 : Displays the current system date and time.
 : The system will produce low-quality images after the Machine has worked for
a long period
because the X-ray generator naturally undergoes minor changes over time. Click
Calibrate to restore image quality.
5.2.1 DeviceOperating Area
5.2.2 RestoringImages
Click to restore processed images to original scanned images.
5.2.3 Controlling Conveyor Belt
Click to set the conveyor belt to move from right to left, stop the conveyor
belt, and set the conveyor belt to move from left to right respectively.

[键入文字]
5.2.4 Navigating Images
Click to view previous and next images.
5.2.5 ImageZooming Out/In
Click and to zoom in and out of (maximum x8) images.
5.2.6 Image Processing Function Shortcut Keys
Combine image processing functions through buttons .
5.3 ImageProcessing FunctionsArea
In the image processing functions area, you can view and edit currently displayed
images. The following image processing functions are supported and you can also
combine multiple functions as needed.
Figure 5-3 Image processing functions area
 Super Enhancement: Adjust image brightness and edge to enhance image
effect.
 BW: See Table 5-3 for the comparison on the display effects.
 High Penetration : Increase image contrast of dark areas. These dark areas
correspond with impenetrable materials with a high X-ray absorption rate, which
usually have high density (such as lead and steel) or are very thick.
 Low Penetration: Increase image contrast of bright areas. These bright areas
correspond with penetrable materials with a low X-ray absorption rate, which
usually have low density or are not particularly thick (such as clothing and paper).
 OM : Use this function for key inspections of inorganic materials and
mixtures. Usually, prohibited metal tools (such as knives and daggers) are
inorganic materials, while the mixing of such prohibited items and daily
necessities (such as clothing and food) affects the judgment of the operator.
 IM: Use this function for key inspections of organic materials and mixtures.
Usually, hazardous items (such as drugs and explosives) and daily necessities
(such as clothing and food) belong to organic materials, while the inspected
objects mixing such organic materials and thin knives or metal electric products
canbe considered as mixedsubstances.
 Inverse: Check small or thin high-density threadlike objects (such as metal wires)

with an effect similar to the negative film. The function displays objects with high
absorption rate in bright colors and objects with low absorption rate in dark colors
without changing the current color tone.
 Brightness Adjustment: Increase or reduce image brightness. The grade in the
system ranges from -5 to +5.
 Image Scan : Change the brightness of images by adjusting gray values. The image
changes from bright to dark and dark to bright automatically. With this function
you can see the object structure with more details.
Table 5-3 Comparison on display effects
Image
Function
Black-and-white display
Inverse color display
High penetrating display
Low penetrating display
Super enhancement display
Colorful display

[键入文字]
5.4 SystemMenuSettings
5.4.1 System Menu Function
Click to view the system menu interface, which includes user management,
parameter settings, curve, image browsing, function key settings, and system
information.
5.4.2 User Management
: Click Account and the prompt box for the user management is displayed.
 Operator : Operators have permissions to modify parameters including roller energy-saving
delay, automatic triggering, and image flip, and log in without password.
 Roller Energy-saving Delay (min) : The amount of time the roller stops for when items are
not passing through the inspection tunnel.
 Automatic Triggering (0: Disable, 1: Enable): Indicates whether automatic
sensing is set at the tunnel entrance. Set the value to 0 if you do not need the conveyor belt
to run automatically.
 Image Flip (0: Disable, 1: Enable): Displays the image upside down.
 Engineer: Enter the password to access permissions. Engineers have permissions
to set parameters including roller energy-saving delay, automatic triggering,
image flip, image direction, and roller direction. Engineer’s permissions are mainly used
for changing the direction of images and the roller.
 Image Direction (0: Right, 1: Left, 2: Auto): Set the direction of images to scroll from left to
right or from right to left on the monitor.
 Roller Direction (0: Forward, 1: Backward) : Set the roller direction to be consistent with
the directions in the deviceoperatingarea.
Figure 5-4 Parameters
 Administrator : Have permissions to set parameters that are related to device testing and device
information. These permissions are currently not available.

5.4.3 Image Browsing
 : Browse, search, and copy previously scanned images.
 : The folder name format is YYMMDD and the file name format is
hhmmss. You can copy the whole folder or a single file.
 : Search forpreviouslyscanned images by date.
 :
selecting .JPEG.
Select the format of the images to be exported. We
recommend
 : Select the path to store exported files.
5.4.4 FunctionCombinationKey
Customize image processing functions for buttons P1, P2, and P3.
Organic material removal and inorganic material removal functions are available only
when the detection chip supports high energy and low energy.
Figure 5-5 Button settings

[键入文字]
6. Routine maintenance work
In order to ensure the long-term stable operation of the equipment, the operator should pay
attention to the regular inspection and daily maintenance of the equipment. During the equipment
maintenance process, it can only be carried out after the power is cut off.
The basic contents of daily maintenance work are as follows:
1. The equipment should be installed in a ventilated and dry environment to prevent high
temperature and humidity from affecting the operation of the equipment;
2. When the equipment is running, it is strictly forbidden to put the liquid in the semi-sealed state
on the conveyor belt to avoid the liquid from being spilled.
To the inside of the device, cause a short circuit and burn out the accessories;
3. It is strictly forbidden to place overweight items on the conveyor belt to avoid overload
operation and damage the electric drum;
4. It is strictly forbidden to place ultra-wide or ultra-high items on the conveyor belt to prevent
items from getting stuck in the detection channel;
5. Regularly remove dust and foreign objects on the conveyor belt and lead curtain;
6. In order to extend the service life of the electric drum, the electric drum should be avoided from
idling for a long time;
7. For equipment that has been stored for a long time (more than one month) and is not in
operation, the user should warm up the equipment for 10 minutes after turning on the equipment
before scanning.
8. Avoid sharing the power supply between the equipment and other large equipment, so as not to
affect the normal operation of the equipment;

#24, Shambavi Building, 23rd Main, Marenahalli, JP Nagar 2nd Phase, Bengaluru - 560078
Phone : [phone] | Email : [e-mail]
www.esslsecurity.com