Eterna LEDTWNSPOT Service manual

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European “WEEE
Directive” eective August 2005—UK WEEE Regulations
eective 2nd January 2007). Environment Agency
Registered Producer: WEE/GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF ITS
LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE
IT WHERE FACILITIES EXIST  DO NOT DISPOSE WITH
HOUSEHOLD WASTE.
CLEANING:
Clean this tting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return it
to the place where you bought it. Our Technical Team
will gladly advise on any Eterna Lighting product, but
may not be able to give specic instructions regarding
individual installations.
For breakage information visit:
www.eterna-lighting.co.uk
Model:
LEDTWNSPOT
IP65 LED Emergency Twinspot Fitting
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
3 HOURS DURATION IN EMERGENCY MODE
Pack contents:
1 x LED tting
1 x Maintenance check record
Email: [email protected].uk / [email protected].uk
Visit our website: www.eterna-lighting.co.uk Made in ChinaIssue 1015

READ THIS FIRST:
This product must be installed by a competent
person in accordance with the current building
and IEE wiring regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.
The batteries supplied with this tting are
consumable parts and therefore may be outside of
any warranty oered.
This unit is suitable for indoor and outdoor use only.
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
Ensure that the tting will be accessible after
installation for maintenance and self testing.
When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product must be connected to earth
termination.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.
LAMP REPLACEMENT:
This luminaire has sealed LED lamps and is
maintenance free, no lamp replacement is required.
BATTERY REPLACEMENT:
If after routine operation check, the lamp does not
remain lit for the three hour period, a new battery
pack may be required.
01) Switch o the electricity at the mains and allow
batteries to fully discharge then reconnect to
supply and allow charging for 24 hours.
02) Test again for 3 hours, if light does not remain lit,
then change the battery pack as follows:
03) Remove four screws and lift o front cover plate.
04) Unplug the battery lead.
05) Remove the two screws from the clamping
bracket that secure the battery pack in place and
lift the battery pack out of the tting.
06) Write current date on the new battery pack and
t new battery pack securing in place with the
screws, nuts and washers previously removed.
07) Reconnect battery.
08) Replace and x front cover plate.
09) Restore power and allow charging for 24 hours.
10) Perform full operation check and update test
record.
REPLACEMENT BATTERY TYPE:
3.6V 6Ah NI-CD batteries.
INDUSTRIAL BATTERIES:
Within certain products Eterna Lighting Ltd places lead
acid, lithium ion, nickel cadmium & nickel metal hydride
batteries on the market. Industrial batteries are subject
to waste regulation under the Waste Batteries and
Accumulators Regulations 2009 and should be disposed
of responsibly. Purchasers may be able to dispose of
their waste industrial batteries locally via legitimate
licensed trade waste contractors. Eterna is obliged
to take back, free of charge and within a reasonable
time, waste industrial batteries of the same chemistry
supplied to a Purchaser, for treatment and recycling
and is required to do this in any calendar year new
industrial batteries are placed on the market. In certain
circumstances, this may include batteries not originally
supplied by Eterna. If any Purchaser requires Eterna
to take back Industrial batteries, they should write to
the Operations Director, Eterna Lighting Ltd, Huxley
Close, NN8 6AB, who will then advise on the necessary
arrangements for the receipt, proper treatment and
recycling of, the waste industrial batteries.
INSTALLATION:
Choose the location of your new tting giving
consideration to all of the points listed above.
01) Remove four screws and lift o front cover.
02) Make cable entry hole using an appropriate
hole cutter and drill out xing points in back of
housing.
03) Using the back of the tting as a template, mark
and drill out xing holes on your mounting
surface.
04) Prepare xing points to mounting surface as
appropriate.
05) Fitting a cable gland will also be necessary if
moisture or weather-proong is required.
06) Thread the supply cable through the gland and
into the tting.
07) Secure the back of the tting to the mounting
surface using suitable xings and apply
silicon sealant to the xings if IP rating is to be
maintained.
08) Connect the un-switched supply cable to
terminals marked L E N.
09) Mark the current date on the battery pack.
10) Connect the battery lead.
11) Ret the front cover and tighten screws.
12) Restore the power and check tting is working
correctly. Two green LED lights should always be
present indicating the tting is charging and the
lamp is healthy.
OPERATION CHECKS:
Periodic testing should be carried out to ensure
emergency lighting is operating correctly.
Interruption of the supply, causing the tting to be
energised from the battery, should be carried out by
the operation of a local keyswitch or other isolation
device. During this period all ttings should be
examined visually to ensure that they are functioning
correctly. At the end of the test period the supply
shall be restored and all indicator lamps or devices
checked to ensure that the normal supply has been
restored.
DAILY:
Visual inspection of the battery charge LED.
EACH MONTH:
Isolate the power supply for a period sucient to
ensure that each lamp is illuminated. Endorse the
test record form supplied.
ONCE EACH YEAR:
Isolate the power supply and check that the light is
still illuminated after 3 hours. Endorse the test record
form.
Because of the possibility of a failure of the normal
lighting supply occurring shortly after a period of
testing of the emergency lighting system or during
the subsequent recharge period, all full duration
tests shall wherever possible be undertaken
preceding time of low risk to allow for battery
recharge.
NOTE: please keep this instruction booklet and
the test record in a safe place. A re ocer or
other authorised person may want to see your
record of inspection and testing.
IMPORTANT NOTES:
The ballast and control gear must be operated only
within the enclosure supplied. The gear must not be
operated outside of the enclosure.
The battery charging circuit and DC ballast are
separated from the mains by at least basic (single
layer) insulation.
When energised by a constant mains supply, the
battery will be constantly charged whether or not
the lamp is illuminated. On failure of the constant
mains supply, the tting will switch automatically
using transistorised switching from battery charging
to battery discharge powering the lamp whether
or not the lamp was illuminated before the power
failure. Both the mains and battery supplies
incorporate fuse protection, see tting for location
and rating.
NOTE: Wires should be
stripped 13-14.5mm
for best t with the
push-t terminal block.
13-14. 5mm
Wire

Month
Test
Year: Year: Year: Year: Year:
Sign Date Sign Date Sign Date Sign Date Sign Date
01 Short
02 Short
03 Short
04 Short
05 Short
06 Short
07 Short
08 Short
09 Short
10 Short
11 Short
12 3 Hour
Endurance
INSTALLATION, MAINTENANCE
AND OPERATION CHECK RECORD
Product
Code:
Product
Description:
Product
Location:
Installation
Date:
Installation
Test Duration:
Installed
By: