ETI NETCOM ADH DC User manual
MODEL ADH DC
AUTOMATIC AIR DEHYDRATOR WITH AC POWER SUPPLY
QUICK REFERENCE INSTALLATION GUIDE | PART NO. 25548 REV 0.0
PART NO. DESCRIPTIONQTY.
25527
25548
18198
23428
14513
23245
24567
10641
ADH NETCOM, DC
ADH NETCOM Installation Sheet (this document)
1/8” NPT to 1/4” Barbed Brass Fitting
1/8” NPT to 3/8” Barbed Brass Fitting
1/8" NPT to 1/4" Barbed Elbow Brass Fitting
Mounting Bracket
Self-Locking Rack-mounting screw (#8-32)
#8 Split Washer
1
1
1
1
1
4
8
8
Connect feed hose to 1/8” NPT outlet using 1/4” or
3/8” barbed fitting supplied.
Connect required data and alarm relay ports. RS-422
and RS-232 ports may require configuration changes
via the web interface. See Instruction Manual for
more information.
Connect AC power. System can be connected to 100
VAC – 240 VAC power without requiring any
configuration change.
1.
2.
3.
CONNECTIONS
UNIT DOES NOT HAVE POWER SWITCH. SYSTEM WILL START WHEN POWER IS APPLIED.
The ADH NETCOM Automatic Dehydrator with AC Power is permanently connected
equipment and does not have an internal disconnect device. A readily accessible disconnect
device, short circuit, and current protection shall be provided and are not supplied by ETI When
power is applied, the system will start.
QUICK REFERENCE INSTALLATION GUIDE | PART NO. 25548 REV 0.0
2
RACK MOUNTING
The dehydrator is equipped with positions
for either flush-mounting (for dual-post racks
and enclosures) or center- mounting (for
single-post racks).
If using mounting rails (not supplied), do not
install mounting brackets.
WALL MOUNTING CONFIGURATION
To configure the dehydrator for wall mount
installation, remove the front panel and the
portion of the vented cover with the ETI logo.
Reinstall the front panel so that it will be in
the new front position once the dehydrator is
positioned for wall mounting. Reinstall the
small vented panel so that it will be in the
new bottom position.
WALL MOUNTING
Ensure the mounting surface and hardware
are suitable to support a static load of
approximately four times the weight of the
unit, or 64 pounds (29 kg). Use four
appropriate 5/16" mounting fasteners to
attach the unit and ensure stable mounting.
The dehydrator is equipped with four
brackets for wall mounting.
RESET
ETHERNET
ALARM
RELAYS
RS422 A /RS422 B
EQUIPMENT
GROUND MODEL
S/N
VOLTS
AMPS WATTS
HERTZ
PRESS
.
P/N
RANGE
ETI INC.
SOUTH BEND, INDIANA U.S.A
ADH N ETCOM
2 0 -7 5 V DC
5.0 A@ 2 0 V DC 1 0 0
DC
0.1 -7 .5 p si
2 5 5 2 7
0 0 0 1
SUPPLY SUPPLY
20-75 VDC
- +
2
1
- +
RS232
QUICK REFERENCE INSTALLATION GUIDE | PART NO. 25548 REV 0.0
3
Your Information Technology Department is the best source of information if you encounter problems or difficulties in
connecting to or communicating with the dehydrator. The ADH NETCOM Ethernet communications run at 10Base-T and half
duplex. It is recommended that the network interface to the ADH NETCOM be manually set to these parameters and NOT to an
auto-configure mode.
After changing the IP address of your dehydrator to a network other than the default 192.168.52.0 you will not be able to access
the dehydrator from the configuring computer unless that computer is reconfigured for the newly assigned network address.
Temporarily assign computer an IP address in the
192.168.52.0 network range, typically 192.168.52.1,
with the subnet 255.255.255.0
Connect the dehydrator to your computer either
directly or through a network. For direct connections
a cross-over cable or switch may be required for
connecting to an older computer; an Ethernet patch
cable will work in most other cases.
Open a web browser and connect to web interface at
HTTP: //192.168.52.9
1.
2.
3.
IP SETTINGS
Go to Configuration page
If using a fixed IP address, select “Use the following IP
address:” Then set the IP address, mask and gateway.
If using DHCP, select “Obtain IP Address
Automatically.”
Click Submit. You should see a message that the
dehydrator is rebooting.
1.
2.
3.
4.
CONFIGURING IP ADDRESS
Using a web browser, connect to the dehydrator. Go
to the Configuration page
Using the Units pull-down select English (PSI) or SI
(mbar).
To change the operational pressure setting enter the
following:
Low Alarm - The pressure at which Low Pressure
will cause an alarm condition.
Low Limit - The low set point at which the unit will
start pumping.
High Limit - The high set point at which the unit
will stop pumping.
High Alarm - The pressure at which High Pressure
will cause an alarm condition.
Click submit.
1.
2.
3.
4.
CONFIGURING PRESSURE
IP Pressure Parameters Module
Configuration Module
QUICK REFERENCE INSTALLATION GUIDE | PART NO. 25548 REV 0.0
4
For technical help, questions or comments concerning this
product or any ETI product contact Customer Service 8:00 a.m. -
5:00 p.m. Eastern Time.
networketi.com
ETI
1850 North Sheridan Street
South Bend, IN 46628
Email:
Web:
Mail:
CONTACTING CUSTOMER SERVICE INSTALLATION NOTES
ETI’s two year limited warranty covering defects in workmanship
and materials applies. Contact Customer Service for complete
warranty information.
LIMITED WARRANTY
ETI makes no representations or warranties, either expressed or
implied, with respect to the contents of this publication or the
products that it describes, and specifically disclaims any implied
warranties of merchantability or fitness for any particular
purpose. ETI reserves the right to revise this publication, and to
make changes and improvements to the products described in
this publication, without the obligation of ETI to notify any person
or organization of such revisions, changes or improvements.
DISCLAIMER
Other ETI Dehumidifier manuals
