Eureka 4320 series User manual

Upright Vacuum Cleaner
Owner’s Guide
4320 – 4370 Series
4440 – 4470 Series
IMPORTANT
Do not return this
product to the store.
For assembly problems or
questions contact: Eureka’s
Customer Service Division toll
free at 1-800-282-2886*, 7 a.m.
to 8 p.m., Central Standard
Time, Monday through
Saturday.
For replacement of broken
or missing items to be
shipped direct to you, call
1-800-438-7352*, 8 a.m. to
4:45 p.m., Central Standard
Time, Monday through Friday.
*En Mexico llame al 5670-6169
Index
Important Safeguards ........... 2
Service Information............... 4
Assembly ........................... 5-6
Use........................................ 7
Thermal Cut Off ..............4 & 7
Accessories........................... 8
Dirt Alert................................ 9
Brush Roll ........................... 10
Brush Roll Belt ............... 10-11
Dust Bag ........................ 11-12
Hose Blockage............... 13-14
Filters .................................. 15
HEPA Filter.......................... 15
Light Bulb ............................ 16
Problem Solving.................. 18
Customer Order Form......... 19
Warranty.............................. 21
www.eureka.com
Household Type

IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury:
•Do not use outdoors or on wet surfaces.
•Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and
before servicing.
•Do not allow to be used as a toy. Close attention is necessary when used by or near children.
•Use only as described in this manual. Use only manufacturer’s recommended attachments.
•Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service center before using.
•Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do
not run vacuum cleaner over cord. Keep cord away from heated surfaces.
•Do not use extension cords or outlets with inadequate current carrying capacity.
•Turn off all controls before unplugging.
•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
•Do not handle plug or vacuum cleaner with wet hands.
•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that
may reduce airflow.
•This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
•Do not place cleaner on furniture or stairs as the brush roll may cause damage. Place cleaner on floor with the handle in
storage position while using attachments.
•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
•Do not use without dust bag in place.
•Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive
belt.
•Use extra care when cleaning on stairs.
•Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
•Store your cleaner indoors in a cool, dry area.
•Keep your work area well lighted.
•Unplug electrical appliances before vacuuming them.
SAVE THESE INSTRUCTIONS
2

CONSEILS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de blessure:
•Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.
•Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou avant le nettoyage ou l’entretien.
•Ne permettez pas qu’il soit utilisé comme jouet. Une attention particulière est nécessaire lorsque utilisé par ou prés d’un
enfant.
•Suivezlesrecommandationsd’utilisation de cemanuel. Utilisezuniquementlesaccessoires recommandés parlefabriquant.
•Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l’aspirateur ne fonctionne pas comme il le devrait, s’il a été
échappé, s’il est endommagé, s’il a été laissé à l’extérieur ou échappé dans l’eau, retournez-le à un centre de service
avant d’utiliser.
•Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de poignée. Ne pas fermer une porte sur
le cordon ou tirer le cordon sur des coins ou bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le
cordon à distance des surfaces chauffantes.
•Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour transporter le courant.
•Fermer tous les contrôles avant de débrancher.
•Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le cordon.
•Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.
•Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquées; assurez-vous qu’elles soient
dégagées de poussière, mousse, cheveux ou toute autre chose qui pourrait réduire le passage de l’air.
•Cet aspirateur créé de la succion et contient un rouleau-brosse tournant. Tenir les parties mobiles et les ouvertures loin
des cheveux, du linge, des doigts et de toute partie du corps.
•Ne pas mettre l’aspirateur sur les meubles ou sur les escaliers car le rouleau-brosse peut faire des dommages. Placer
l’aspirateur sur le plancher avec le manche en entreposage position temps que les accessoires sont en usage.
•Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumettes ou cendres chaudes.
•N’utilisez pas sans le sac de poussière en place.
•Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour prévenir des brûlures, évitez de
touché la poulie du courroie lorsque vous réparez la courroie.
•Portez une attention particulière lorsque vous nettoyez les escaliers.
•Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l’essence: Ne pas utiliser dans les
endroits où ces liquides pourraient être présents.
•Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.
•Maintenez un bon éclairage à l’endroit où vous travaillez.
•Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
3

To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée (une des lames est plus large).
Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un
électricien qualifié. Ne pas modifier la fiche.
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust particles.Avoid picking up hard or sharp objects with the cleaner to prevent
bag tears, hose clogs, and fan blade breakage with subsequent motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. For additional service information telephone our toll
free number for the nearest Eureka Authorized Warranty Station. You should know the model, type and serial numbers
when you call:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701,
USA. In Canada write to The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited
Warranty for complete service information.
DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.
4
Rating Plate
The model, type, and serial numbers are indicated on the
rating plate located on the underneath side of the cleaner.
Forprompt and complete service information,always refer
to these numbers when inquiring about service.
Model & Type__________________________
Serial No. _____________________________
MODEL TYPE SERIAL NO.
VOLTS AMPS. HERTZ
SERVICE INFORMATION: 1-800-282-2886
THE EUREKA COMPANY
BLOOMINGTON, ILLINOIS 61701
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly
shuts off, push the switch pedal once and unplug the cleaner. Check the cleaner for a possible source of overheating such as
a full bag, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before
attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the cleaner still
does not run, then take it to a Eureka Authorized Service Center for repair.

5
HOW TO ASSEMBLE
CAUTION: Assemble the cleaner before using.
CAUTION: Moving parts, make sure on/off switch is in off position before plugging in.
NOTE: Features may vary by model yet all parts assemble the same.
Step A Attach Hose (Refer to your hose adapter Step B Attach Handle
CAUTION: Do not catch cord under handle.
Tab
Hose
Adapter
##
##
#
4. From rear of cleaner, align handle with groove and
slide onto cleaner. If necessary, use thumb and
finger pressure to slide handle into position.
5. Once handle is in place, checkthat thehose adapter
tab is completely secure under the ledge of the
handle.
6. Attach handle with two 5/8 inch screws in the
assembly packet. Use either a slotted or Phillips®
head screwdriver.
7. Replace front cover.
1. Remove the front bag cover.
(Only required with Style B adapter.)
2. Locate the tab on the hose adapter of the extension
hose (shortest end). There are two styles, eitherAor B.
Each style assembles identically.
3. Insert hose adapterinto openingon topofunit. The hose
adapter tab must be placed all the way down into
the notch.
Groove
4
Groove
Tab
Ledge 5
1
2
Style B
Style A
IMPORTANT:
Hose
MUST BE
inserted
before attaching
the handle.
3
Notch
style)

6
8. Remove front cover, grasp both sides of bag cover
near top. Push thumbs against center of cover and
pull out on sides.
9. Check to be sure the paper bag collar is secure with
the hose adapter inside the paper bag collar.
10. Replace front bag cover.
11. You will find your cord retainer either at the bottom
of the upper cord hook or on the handle above the
upper cord hook. Firmly push the electrical cord
down into either cord retainer. This will place the
cord out of the way the next time you vacuum.
12. Next wind the cord around the two cord hooks on
the left side of cleaner. On some models the upper
cord hook turns to release the cord. Turn the hook
up to store the cord.
NOTE: For easier access to bag compartment, when
you store the electrical cord use a figure 8
pattern.
13. Secure the plug to the cord to prevent unwinding.
Hose
Adapter
|
|
8
10
Cord
Hook
Step E Store Electrical Cord
Step C Store Hose and Accessories Step D Check Disposable Dust Bag
Combination
Tool
Crevice
Tool
Hook
Hose
Retainer
Tabs
Paper Bag Collar
9
Back View of
handle and
tools on some
models
Dusting
Brush
Upholstery
Nozzle
Cord
Hook
Cord
Retainer
11 11
12
12
Cord
Retainer
Extension
Wand or
Wands
Carrying
Handle
HEPA Filter
(on some
models)

7
Clean
Under
Use
Handle
Release
3
HOW TO USE
Theuprightvacuumcleaner designallowsuseon multipletypes
ofcarpeting and on upholstery orbare floors withattachments.
When using the attachment tools, place the handle in the
upright position. Do not place cleaner on furniture or steps
as the brush roll may cause damage.
1. Adjust cleaner height setting knob to lowest position for
maximum cleaning. Adjust to a higher setting to make
pushing easier. For easy adjustments, tilt the cleaner back
to move the setting knob.
2. Unwind all of the electrical cord. Located above the cord
hookis the cord retainer. Firmly push the electriccord down
into the cord retainer. Using the cord retainer will keep the
electric cord up, out of the way while vacuuming.
3. Plug electrical cord into outlet.
4. Step on handle release. Pull handle back to a comfortable
position.
5. Push On or Off power switch.
Store or
Use Attachments
LOW HIGH
4Handle
Release
5ON/OFF
1
Thermal Cut Off
This cleaner has a special thermostat that protects the
cleaner in case of motor overheating. If the cleaner
suddenly turns off, follow this procedure:
1. Push on/off pedal once.
2. Unplug cleaner.
3. Check for source of overheating problem (i.e. full bag,
clogged hose or clogged filter).
4. If a full bag, clogged hose or clogged filter is found,
replace the bag, unclog the hose or replace the filters.
5. Wait at least 30 minutes before attempting to reuse the
cleaner.
6. After 30 minute cool down period, plug the cleaner in
and push the switch pedal. The cleaner should turn on.
7. Ifthe cleanerstill doesnot operate,take it toany Eureka
Authorized Service Center for repair.
3
2
Cord Retainer
Cleaner Height Setting
WARNING: Avoid injury. Keep loose clothing, hair, fingers,
and all other parts of body away from any
movingpart(suchastherevolvingbrush).Turn
off the switch and unplug the cleaner before
changing the cleaner height setting.
Thefront ofthe cleanerhas anadjustment thatraises orlowers
the cleaner base to match the type of carpet. With the cleaner
cord unplugged, set the adjustment to lowest setting for
maximum cleaning. If the cleaner is difficult to push, move
adjustment to next highest setting until cleaner is comfortable
to push. The brush roll must reach the carpet for effective
cleaning.
NOTE: For ease in moving the adjustment knob, place
handle in operating position and tilt cleaner back
to remove weight from front wheels.
NOTE: When handle is in upright position, brush roll is
lifted off carpet. This is normal. Height adjustment
will not change brush roll level until the cleaner’s
handle is moved into the operating position.

8
How To Use Accessories
NOTE: Do not place cleaner on furniture or
steps as the brush roll may cause
damage. Place cleaner on floor with
the handle in storage position while
using accessories.
Crevice Tool
Dusting
Side
..
..
.
Combination Toolgives two types of cleaning tools. (On some
models.)
•Use brush side to dust furniture, blinds, books, lamps, shelves.
•Use upholstery side for curtains, draperies, cushions, fabrics.
..
..
.
Depending on which cleaner you purchased, you can
have any combination of the following accessories.
1. Remove hose from rear of cleaner.
2. Place desired accessory onto end of hose.
•Turn ridge end to center. •Push wands together.
..
..
.
•Pull apart.
Upholstery
Side
..
..
.
..
..
.
•Grasp both wands near ridges.
Nested Extension Wands to add reach.
Extension Wands (Some models use 1 wand)
..
..
.
Dusting Brush is for furniture, blinds, books, lamp shades,
shelves. (On some models.)
..
..
.
Upholstery Nozzle is for curtains, draperies, cushions,
fabrics. (On some models.)
..
..
.
Dusting Brush
Upholstery
Nozzle
Crevice Tool cleans corners, baseboards, between cushions.
..
..
.
Always work with the cleaner below you,
pulling hose from side of cleaner; not the back
or the front of the cleaner.

9
Maintenance of Dirt Alert Feature (On some models)
The dirt alert sensor uses infra-red technology to indicate whether or not floors are clean. When debris breaks the light
beam, the red light comes on indicating additional cleaning is needed in this area. If there is no break in the light beam, the
floor is clean and no light will come on.
When using your new vacuum you may be cleaning deep down hidden dirt missed by your old vacuum causing the light to
stay red longer. With frequent cleaning, after the first few times you use your new Eureka vacuum, the red light should go
on less.
Thered light indicatesdirt, dust, etc. is stillbeing removed
from the area being cleaned.
NOTE: The dirt alert feature is not intended to be used for above the floor cleaning with attachments.
To check if dirt sensor is working properly.
1. While the red light is on, tip the vacuum backwards on rear
wheels, lifting the brush roll off the carpet a couple of inches.
2. After a few seconds the red light should turn off.
HINT: New carpeting has loose carpet fibers which will trip
the red light sensor beam.
Infrared
Emitter and
Sensor
..
..
.
Hose Retainer
Hose
How to Check the Dirt Alert Sensors

10
HOW TO MAINTAIN
The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the bag,
belt, and brush roll often.
Brush Roll
The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it continues
brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length,
hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brush roll.
Brush Roll Belt
The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be sure it is
in good condition. Replace the belt if it stretches, cracks or loses tension. Cut away any hair or threads wound around the
brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly.
How To Replace Brush Roll Belt
NOTE: Turn off the switch and unplug the electrical cord before replacing belt. Belt pulleys can become hot during
normal use. To prevent injury, avoid touching the motor pulley when checking the belt.
1. Lower handle to floor to change belt.
2. Loosen, but do not remove, two screws to release
hood. Lift hood to remove.
2
2
1
3. Lift left end of brush roll.
4. Remove and discard belt.
Motor
Pulley
Belt
3
Brush
Roll
4

11
5
5. Place new belt around motor pulley.
..
..
.
7
6
Left Side View
6. Place belt around brush roll pulley.
7. Align left end cap with square in base. Push end cap
into place; see left side view.
8
8. Pull right side of brush roll to stretch belt. Secure right
end cap into base.
9
9. Rotate brush roll to seat belt.
10. Replace the hood. Make sure hood front is behind
furniture guard. Hood should seat onto self-locating
screw tabs.
11. Tighten screws.
Use GENUINE EUREKA replacement belt, 54312. Look
for the GENUINE EUREKA product symbol.
Disposable Dust Bag and Filters
The disposable dust bag plays a very important role in
the efficiency of a vacuum cleaner. The purpose of the
paper bag is to trap dirt.As the bag traps dirt, it must also
be porous enough to allow air to pass on through. If the
paper bag becomes clogged, no air can pass through the
cleaner and no cleaning can take place regardless of how
powerfulthe unit. Changethe dustbagand checkthe filters
frequently. Some fine particles can restrict airflow very
quickly and will decrease performance even before the
bag appears to be full.
When vacuuming carpet fresheners or cleaners, powder,
plaster dust, or similar fine substances, the bag and filters
may require more frequent maintenance.
Bag Change Indicator (only for models
with a Bag Change Indicator)
Some models feature a Bag Change Indicator to remind
you to change the bag. The indicator on the bag cover
moves into the window as the airflow through the bag
decreases. Certain types of fine particles like powder,
plaster dust, or fine road dust can restrict airflow very
quickly. Thefine particles will decrease performance even
before the bag appears to be full. Change the dust bag to
restore maximum performance.
Besure to use GENUINE EUREKAFilteraire bagsfor best
performance. If a clean dust bag does not restore
maximumperformance, check forobstructions in thehose
or airflow passage.
Bag
Change
Indicator

12
How To Replace Bags–Style AA Filteraire
NOTE: Turn off the switch and unplug the electrical cord before changing dust bag. Never operate the vacuum
cleaner without the dust bag or the filter.
NOTE: Style AA Filteraire bags must be used to maintain HEPA grade filtration and prolong the life of the HEPA
filter.
NOTE: Models without HEPA filter option, may use Style AA bags rather than Style AA Filteraire.
It may be more convenient to lower the handle to the floor before changing the bag.
To Remove Bag:
|
|
Front
Cover
A
|
|
B
A. Remove front cover. Grasp both sides of bag cover
near top. Push thumbs against center of cover and
pull out on sides.
B. Grasp bag collar; pull down slightly and out toremove
bag.
To Replace New Bag:
C. Fold sides of paper bag below bag collar.
D. Align bag collar hole and notch with hose adapter.
E. Placebag collar cornerson ledges. Pushcollar to rear
of compartment. Check to be sure hose adapter
inserts into bag collar.
F. Tuck bag into bottom and along sides.
G. Replace front cover. Make sure disposable bag does
not catch under front cover.
Bag
Collar
D
E
C
Bag
Side
E
* We recommend using only Genuine Eureka
Filteraire Bags, part number 58623.

How to Check and Clear Hose Blockages
Low suction or poor pickup may be due to a blockage in the vacuum cleaner.
1. Remove hose and check suction at end of hose - if little or
no suction, check disposable dust bag. Change if needed.
If no improvement proceed to step 2.
NOTE: Turn off the switch and unplug the electrical cord
before clearing hose.
2. Remove the handle from the vacuum cleaner by removing
the two screws and sliding the handle towards the rear.
3. Once the handle is removed, disconnect the attachment
hose from the unit by lifting straight up on the hose adapter.
Check for any obstructions that may be in the hose. Any
obstructions can be removed by using a blunt instrument to
clear the hose. Flexing the hose may help loosen the clog.
4. Reinstall the hose after clearing the clog. Make sure the
hose is inserted into the top of the vacuum cleaner before
reattaching the handle.
NOTE: If no improvement in performance on carpet, proceed
to following page.
2. Remove handle.
3. Disconnect hose.
..
..
.
1. Remove hose and check suction at end of
hose.
##
##
#
4. Reinstall the hose and handle.
1
24
##
##
#
3
13

14
Handle
Release
1. Remove the attachment hose from the lower hose
retainer and look into the hose retainer for any
obstructions. Proceed to Step 2 to check for any other
blockages.
4. Check forblockages in thebrush roll area and remove
any obstructions found there. The base hose can be
cleared of any blockage by using a blunt instrument.
5. After the blockage is removed, replace the hood and
tighten the two hood screws (see Fig. 2). Raise the
handle to the upright position (see Fig. 3) and replace
the hose into the lower hose retainer.
Upright Position
Operating Position
Lowest Position
for cleaning
under furniture
..
..
.
How to Check and Clear Blockages in Base
2. Remove thehood byloosening thetwo screwslocated
on the top of the hood and lifting upward.
3. Step on the handle release and lower the handle all
the way to the floor.
s

15
To remove HEPA cartridge filters
1. Push down latch and pull filter cassette back.
2. Then lift filter up and remove.
To replace HEPA cartridge filters
1. Place bottom tabs of filter cassette into slots.
2. Rotate filter toward cleaner.
3. Push upward on the latch to secure into place.
NOTE: To have the benefit of a sealed HEPAsystem,
you must use one of the HEPA cartridge filter
systems.
To remove HEPA/Micron filters from
filter frame .
1. Push down latch and pull filter frame back.
2. Then lift filter up and out of filter frame.
To replace HEPA/Micron filters into
filter frame .
1. Place new filter in filter frame. Place bottom tabs
of filter frame into slots.
2. Rotate filter frame toward cleaner.
3. Push upward on the latch to secure into place.
HEPA Cartridge Filters (Only for models
with HEPA cartridge.)
Check the HEPA filters with each disposable dust bag
change. Replace twice a year or after every six bag
changes.
HEPA/Micron Filters in Filter Frame
(Only for models with HEPA/Micron filter frame)
Check the HEPA/Micron filter with each disposable
dust bag change. Replace twice a year or after every
six bag changes.
Latch
Tabs
Filter Cartridge
(One complete
unit)
Filter Frame plus
filter (depending
on your vacuum
model)
,

yz{

Filter Filter
Frame
Motor Filter
Check the motor filter with each disposable dust bag
change. Clean or replace as needed.
To Clean Motor Filter
1. Remove filter from inside bag compartment, lower
left side.
2. Shakefilter to remove excess dust.If necessary,the
filter can be cleaned by vacuuming with another
cleaner.
3. Reinstall filter with stiff/printed side down. Slide
under back ledge and filter retainer. Install with
colored/smooth side down.
Back Ledge 3
Filter Retainer 3
,

yz
{||
31 and

16
Use 15 watt replacement light bulb, part
number 48815.
How To Change Light Bulb (only for models
with a headlight)
NOTE: Turn off the power switch and disconnect the
electrical cord before changing light bulb.
1. Lower handle. Remove two screws from lens cover.
2. Pull lens cover from cleaner.
3. Pull light bulb and socket toward front.
4. Push light bulb into socket; turn to release.
5. Place new light bulb into socket; turn to secure.
6. Push light bulb and socket back so bulb will not touch
lens cover.
7. Replace lens cover.
8. Secure with two screws.
3
5
4
1
HOW TO MAINTAIN (continued)
Exhaust
Filter
Door
Micron and HEPA Exhaust Filters(Only
for models with the exhaust filter door)
Change micron or HEPA exhaust filter every 3
months.
To Replace Micron or HEPA Exhaust
Filter
1. Lower the handle. Open exhaust filter door; push
toward the left side.
2. Grasp filter and pull out.
3. Push new filter into cleaner, smooth side facing out .
4. Close exhaust filter door; push toward right side.
Replace all filters with genuine Eureka replacement
filters.
2
3
..
..
.
..
..
.
Micron or
HEPA
Filter
Exhaust Filter
Door
..
..
.
..
..
.

17
Some models will come complete with an extra bonus hose which is ideal for cleaning stairs.
HOW TOASSEMBLE AND USE
STAIR CLEANING HOSE (Only on Certain Models)
Step 3 - You are ready to clean your stairs.
Step 2 - Connect the hose cuff to the end of the
bonus hose.
Step 1 - Remove the hose attached to the cleaner.
WARNING
Always work with the cleaner below you, pulling
hose from side of cleaner; not the back or the front of
thecleaner. Ensure it ispositionedsideways up against
the bottom step.
NEVER STAND ANY CLEANER ABOVE YOU.
NEVER POSITION ANY CLEANER ON THE
STAIRSAS THIS COULD DAMAGE THE CARPET.
WARNING: Never position any cleaner on the stairs as this could damage the carpet.

Motor will not start. Electric Plug Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
Motor suddenly stops. Thermal Cut Off Refer to page 7.
Does not clean the carpet or Disposable Dust Bag Change the bag. Hint: If picking up fine dust, the bag
floor. and Filter(s) may not look full, but a fine substance tends to reduce
suction when it blocks the airflowthrough the paper bag
and filter(s). Make sure the dust bag is installed properly.
Make sure bag cover is installed properly.
Belt Replace a cut, loose or out of shape belt.
Brush Roll Clean hair and thread from bristles and end cap area.
Replace brush roll if bristles are worn.
Hose Remove any clogs from the hose that restrict the airflow.
No suction at the end of the Disposable Dust Bag Change the bag. Hint: If picking up fine dust, the bag
hose. may not look full, but a fine substance tends to reduce
suction when it blocks the airflowthrough the paper bag.
Hose Remove any clogs from the hose that restrict the airflow.
Check both ends of the hose. (See pages 13-14)
Headlight not working. Light Bulb Replace light bulb.
Noise from the brush roll area. Brush Roll Remove hood and clean debris from the brush roll area.
Belt Replace a cut, loose or out of shape belt.
Cleaner is hard to push. Cleaner Height Setting Turn adjustment knob to a higher position. Hint: Put
handle in operating position. Tilt the cleaner back to
raise the front wheels off floor. Then turn the knob.
Belt Replace a cut, loose and out of shape belt.
Brush roll will not turn. Belt Replace cut, loose or out of shape belt.
Burning smell. Belt Replace cut, loose or out of shape belt.
Dirt Alert red light will not go off. New carpet fibers. Over time loose new carpet fibers will diminish and will
not trip the dirt alert sensors.
Dirt Alert red light will not come on. Dirt sensor is not working. Call 1-800-282-2886 7 a.m. to 8 p.m., central standard
time, Monday through Saturday for the nearest authorized
Eureka service center.
Cleaning height knob will not Cleaner Height Setting Hint: Put handle in operating position. Tilt the cleaner
turn. back to raise the front wheels off floor. Then turn the
knob.
Missing parts. Call 1-800-438-7352 between 8:00 a.m. and 4:45 p.m.,
central standard time, Monday through Friday. Know the
model and serial numbers when you call.
Questions? Call 1-800-282-2886 7 a.m. to 8 p.m., central standard
time, Monday through Saturday. Know the model and
serial numbers when you call.
PROBLEM SOLVING
NOTE: Turn off the switch and unplug the electrical cord before servicing.
PROBLEM CAUSE SOLUTION
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
18
3

58623A
58236A
54926
61333
61120
60285B
60665
58728B
13104-4
61037
26708-119N
60112
54785A
54002
60169
54646A
60169-1
60166
61224-1
60252-2
60251-2
61308-1
48815
5.99
3.99
9.99
1.99
2.99
19.99
2.99
4.39
2.49
4.49
2.69
22.69
10.39
12.99
18.79
8.69
17.39
29.99
11.29
12.59
13.89
15.89
1.69
Filteraire Disposable Bags (style AA), package of 3
Disposable Bags (style AA), package of 3
Disposable Bags (style AA), package of 10
Motor Filter - package of 2
Belts (style U) - Extended Life, package of 2
HEPA Filter
Micron Exhaust Filter, package of 2
Nested Wands
Extension Wand
Combination Tool
Use as Dusting Tool or Upholstery Tool
CreviceTool
Expandable Crevice Tool
Floor Brush
Micro Tool Set for Keyboards
Wood (15 inch)
Wood (12 inch)
Wood (12 inch) - 4600 series
Name
Address (street address needed for UPS)
City State Zip
Telephone (Day) (Eve) (Fax)
TOTAL ENCLOSED
VACUUM CLEANERS
Name
Address (street address needed for UPS)
City State Zip
Telephone (Day) (Eve) (Fax)
S
O
L
D
T
O
S
H
I
P
T
O
Part No. Qty. Price (USD) Total
70352 © 2001 White Consolidated Industries, Inc.
Printed in U.S.A.
Method of payment (no C.O.D. orders)
Check or money order (payable to The Eureka Company). Do not send currency.
Charge to my Visa (13/15 digits) MasterCard (13 digits) Amer. Express (15 digits)
Acct.number Expiration Date
Signature (full name as shown on acct.) TOTAL
Postage & Handling Charge (within U.S.A.)
Tax (add state tax & local taxes as required by law)
Total (prices subject to change without notice)
5.50
Genuine Eureka Bags, Belts and Filters
Accessories/Tools
Miscellaneous Parts
Light bulb (15 watt)
Deluxe Stretch Hose Assembly
Stretch Hose Assembly - without Button Lock
Standard Hose Assembly
Stair Hose - 15 foot
Hose Assembly - with Button Lock
The Eureka Company
P.O. Box 2799
Bloomington, IL 61702-2799
Hoses
Brush Rolls
#
ORDER FORM
2/01
(Not applicable in Canada)
IMPORTANT:
Be sure to include
your model, type,
and serial numbers.
These numbers
may be found on
the rating plate.
Model Number:
Type:
Serial Number:
To Order
By Phone
1-800-
438-7352*
HOURS:
Call between 8 a.m.
and 4:45 p.m.,
central standard time
Monday through Friday.
By FAX
1-309-
823-5789
To Answer Problems
or Questions for U.S.A.
and Canada call:
1-800-
282-2886*
7 a.m. to 8 p.m.
central standard time
MondaythroughSaturday.
*En Mexico Llame
5670-6169
By Mail
Simply fill out
this Order Form.
Please be sure to
include day
and evening
phone numbers.
www.eureka.com