Eureka Heavy Duty User manual

Upright
Vacuum Cleaner
Ownerʼs Guide
www.eureka.com
Index
Important Safeguards
..................
2
General Information
.....................
3
Assembly
.................................
3-4
Use
..........................................
4-5
Dust Bag
......................................
5
Brush Roll
................................
5-6
Headlight
.....................................
6
Brush Roll Belt
.............................
7
Warranty
......................................
8
Repair Parts List
....................
9-19
For location of nearest
Eureka Warranty Station
or service information call
1-800-282-2886.
*En Mexico llame al 5670-6169.

IMPORTANT
SAFEGUARDS
When using an electrical appliance, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS
VACUUM CLEANER.
WARNING
To reduce the risk of fi re, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
•
Do not leave vacuum cleaner when plugged in.
Turn
off the switch and unplug the electrical cord when not in
use and before servicing.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturerʼs recommended attachments.
• Do not use with damaged cord or plug. If vacuum cleaner
is not working as it should, has been dropped, damaged,
left outdoors, or dropped into water, return it to a service
center before using.
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Do not run vacuum cleaner over cord. Keep cord away
from heated surfaces.
• Do not use extension cords or outlets with inadequate
current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair, and anything
that may reduce airfl ow.
• This vacuum cleaner creates suction and contains a
revolving brush roll. Keep hair, loose clothing, fi ngers, and
all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such
as cigarettes, matches, or hot ashes.
• Do not use without dust bag in place.
• Belt pulleys can become hot during normal use. To prevent
burns, avoid touching the belt pulley when servicing the
drive belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up fl ammable or combustible liquids
such as gasoline, or use in areas where they may be
present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
SAVE THESE
INSTRUCTIONS
2
CONSEILS DE
SÉCURITÉ
Lors de lʼutilisation dʼun appareil électrique, quelques précautions
élémentaires doivent être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT DʼUTILISER
VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de
blessure:
• Ne pas utiliser à lʼextérieur ou sur des surfaces mouillées.
•
Fermez le commutateur et débranchez lʼappareil
lorsque
vous ne lʼutilisez pas ou avant le nettoyage ou lʼentretien.
• Ne permettez pas quʼil soit utilisé comme jouet. Une attention
particulière est nécessaire lorsque utilisé par ou près dʼun
enfant.
• Suivez les recommandations dʼutilisation de ce manuel.
Utilisez uniquement les accessoires recommandés par le
fabriquant.
• Ne pas utiliser si le cordon ou la fi che sont endommagés. Si
lʼaspirateur ne fonctionne pas comme il le devrait, sʼil a été
échappé, sʼil est endommagé, sʼil a été laissé à lʼextérieur ou
échappé dans lʼeau, retournez-le à un centre de service avant
de utiliser.
• Ne pas le tirer ou le transporter par le cordon, ne pas utiliser
le cordon en guise de poignée. Ne pas fermer une porte sur
le cordon ou tirer le cordon sur des coins ou bordures pointus.
Ne pas circuler sur le cordon avec lʼaspirateur. Tenir le cordon
à distance des surfaces chauffantes.
• Ne pas utiliser des rallonges ou des prises qui nʼont pas de
capacité suffi sante pour transporter le courant.
• Fermer tous les contrôles avant débrancher.
• Ne pas débrancher en tirant sur le cordon. Pour débrancher,
tenez la fi che et non le cordon.
• Ne pas manipuler la fi che ou lʼaspirateur avec les mains
mouillées.
• Ne pas rien insérer dans les ouvertures. Ne pas utiliser si
des ouvertures sont bloquées; assurez-vous quʼelles soient
dégagées de poussière, mousse, cheveux ou toute autre
chose qui pourrait réduire le passage de lʼair.
• Cet aspirateur crée de la succion et contient un rouleau-brosse
tournant. Tenir les parties mobiles et les ouvertures loin des
cheveux, du linge, des doigts et de toute partie du corps.
• Ne pas ramasser des objets qui brûlent ou fument comme
les cigarettes, allumettes ou cendres chaudes.
• Nʼutilisez pas sans le sac de poussière en place.
• Les poulies du courroie peuvent devenir chaudes pendant
lʼutilisation normale. Pour prévenir des brûlures, évitez
de touché la poulie du courroie lorsque vous réparez la
courroie.
• Portez une attention particulière lorsque vous nettoyez les
escaliers.
• Ne pas utiliser pour ramasser des liquides infl ammables ou
combustibles comme de lʼessence: Ne pas utiliser dans les
endroits où ces liquides pourraient être présents.
• Entreposez votre aspirateur à lʼintérieur dans un endroit propre
et sec.
• Maintenez un bon éclairage à lʼendroit où vous travaillez.
• Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES
INSTRUCTIONS

To reduce the risk of electric shock,
this appliance has a polarized plug (one blade is wider than the other). This plug will
fi t in a polarized outlet only one way. If the plug does not fi t fully in the outlet, reverse the plug. If it still does not fi t, contact
a qualifi ed electrician to install the proper outlet. Do not change the plug in any way.
Afi n de réduire le risque de choc électrique,
cet appareil est muni dʼune fi che polarisée (une des lames est plus large).
Cette fi che ne peut être insérée dans une prise polarisée que dʼune seule façon. Si la fi che ne peut être insérée dans la
prise, retourner la fi che. Si la fi che ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un
électricien qualifi é. Ne pas modifi er la fi che.
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner to prevent
bag tears, hose clogs, and fan blade break age with subsequent motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. For additional service information telephone our toll
free number for the nearest Eureka Authorized Warranty Station.
You should know the model, type and serial numbers
when you call:
USA: 1-800-282-2886
México: 5670-6169
Canada: 1-800-
282-2886
If you prefer, you can write to
Electrolux Home Care Products North America, Consumer Service, P O Box 3900, Peoria,
Illinois, 61612
, USA
. In Canada write to
Electrolux Home Care Products Canada
, 866 Langs Drive, Cambridge, Ontario N3H
2N7. Refer to The Eureka Limited Warranty for complete service information.
DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.
Rating Plate
The model, type, and serial numbers are indicated on the rating plate located on the
underneath side of the cleaner. For prompt and complete service information, always
refer to these numbers when inquiring about service.
Model & Type_________________________
Serial No.
____________________________
3
MODEL TYPE SERIAL NO.
VOLTS AMPS. HERTZ
SERVICE INFORMATION: 1-800-282-2886
ELECTROLUX HOME CARE PRODUCTS
ELECTROLUX HOME CARE PRODUCTS
BLOOMINGTON, ILLINOIS 61701
HOW TO ASSEMBLE
Assembly Packet
The assembly packet is with the ownerʼs guide. The packet contains
two 2-part bolts and two cord hooks. An extra drive belt is also included
with some models.
Step 1
Assemble the Handle
Slip the upper handle and the lower handle together so the handle bolt
holes align and the slots in the handle are positioned as shown in Detail
A. Insert a 2-part bolt (A) in the center of the handle and tighten.
Hold the assembled handle so it curves away from the cleaner. Then
push the handle into the handle socket (D) at the rear of the cleaner.
Align the holes, insert the other 2-part bolt (A), and tighten.
D
A
C
A
B
Detail A

4
Step 2 – Attach Upper Cord Hook
Pull the spring on the electrical cord
upward toward the top of the handle.
Make sure slots in handle are positioned
properly, see Detail A.
Insert the lower half of the spring into
the upper cord hook (B), as shown.
Snap the hook into the upper handle,
directions below.
Step 3 – Attach Lower Cord Hook
Insert the power cord into the lower cord hook (C), as shown.
Snap the hook into the lower handle. Pull up on the cord to
tighten but leave enough slack near the base so the cord
is not strained when the handle is lowered. Wrap the cord
around the two cord hooks. Fasten the plug to the cord to
prevent unwinding.
Step 4 – Install Outer Bag
Hold outer bag with zipper away from han dle.
IMPORTANT: To provide a good gas ket seal, the bag
coupling must seat fi rm ly against the motor base and
not overlap the furniture guard. Start the bag screws D
by hand, then tighten with a screw driv er.
Loop the spring from the top of the bag onto the bag support
located to the back of the upper cord hook (B).
B
BAG
SUPPORT
HOOK
3. SNAP opposite inner
tab into place
1. Place inner
tab into slot
2. Press hook
around handle
E
Lower Cord
Hook
C–
F
D
3
3
4
4
HOW TO USE
The upright vacuum cleaner is designed to be used on
multiple types of carpeting. Do not attempt to use the
upright vacuum cleaner on bare fl oors, as damage to the
fl oor covering may result. Above the fl oor cleaning tools are
available (optional).
Handle Adjustment
With the tip of the foot, press down to release the handle lock
located at the left rear side of the cleaner. Move the handle
and adjust it to the desired position for (1) storing upright, (2)
operating the cleaner at a comfortable height for the user,
and (3) cleaning underneath low furniture.
Power Switch
The power switch is mounted on the motor hood near the
handle. Switch style varies by model and may differ from the
illustration. A push with the foot turns the motor ON; push
again to turn the motor OFF.
Cord Storage
The cleaner has two convenient cord storage hooks attached
to the handle. Wind the cord around the hooks and fasten
the plug to the cord to prevent unwinding.
Handle Lock
Handle Lock
1. Store
2. Use
3. Clean
3. Clean
3. Clean
Underneath
Underneath
Underneath
Underneath
ON/OFF

5
Cleaner Height Setting
WARNING: Avoid injury. Keep loose clothing, hair, fi ngers,
and all other parts of body away from any
moving part (such as the revolving brush).
Turn off the switch and unplug the cleaner
before changing the cleaner height setting.
Adjust the vacuum
cleaner height setting
to match the carpet
pile height. Refer to
the following chart
of rec o mm e n d e d
settings for carpet
types.
The front of the cleaner
has either a knob or
slide adjustment which
raises or lowers the
cleaner base to match
the type of carpet. With the cleaner cord unplugged, set the
adjustment according to the table as a starting point. While
the cleaner is off and disconnected from the outlet, place the
handle in the operating position, tilt the cleaner back to remove
the weight from the wheels, and adjust the setting. Then plug
the cleaner into the electrical outlet, turn on the switch, lower
the handle, and pass the cleaner over the carpet. If the cleaner
is still diffi cult to push, follow the procedure and test the cleaner
at the next higher setting.
Continue testing the setting until the cleaner is comfortable
to move. Moving the knob or slide to the next higher setting
raises the brush roll slightly, making the cleaner easier to push.
However, the brush roll must make contact with the carpet for
effective cleaning.
HOW TO MAINTAIN
The instructions given in this booklet serve as a guide to routine
maintenance. To avoid unnecessary service calls, check the
bag, belt, and brush roll often. Empty or change the bag if it is
full; replace the belt if it is stretched or cracked, and clean the
brush roll bristles if they are wrapped with thread and hair.
Cleaner Care
NOTE: Turn off the switch and unplug the electrical cord
before cleaning unit.
To keep the vacuum cleaner looking new, it can be wiped with a damp
cloth and a mild soap solution, then thoroughly dried. Never use any
type of chemical as chemicals can damage the cleaner. When not in
use, the cleaner should be stored in a clean, dry place.
Dust Bag
The dust bag plays a very important role in the effi ciency of
the vacuum cleaner. The bag traps the dirt and allows the air
to pass through. If the bag (either cloth or paper) becomes
clogged, no air can pass through the cleaner and no cleaning
can take place, regardless of how powerful the unit is. To keep
the cleaner operating at maximum effi ciency, empty or change
the dust bag frequently. Some fi ne particles can restrict air
fl ow very quickly and will decrease performance even before
the bag appears to be full. For that reason, when vacuuming
carpet fresheners or cleaners, powder, plaster dust, or similar
fi ne substances, the bag may need to be cleaned or changed
more often.
NOTE: Turn off the switch and unplug the electrical
cord before servicing the bag. Never operate the
vacuum cleaner without the dust bag.
Recommended
Setting Example of Carpet
Position 1 Low pile as kitchen, indoor,
outdoor
Position 2 Sculptured
Position 3 Plush or thick sculptured
Position 4 Thick plush
If the cleaner has additional height settings, they are for
thicker carpets or where easier pushing is desired. If there
are two height settings, use low for Position 1 and 2 and
high for Position 3 and 4.
1. Pull
zipper
zipper
down
down
5. Place bag
throat on
sleeve
sleeve
How To Change Disposable Dust Bag–
Style F & G
4. Unfold
new
bag
TOP
BOTTOM
BOTTOM
THROAT
THROAT
THROAT
3. Pull bag
throat off
sleeve
2. Roll down
2. Roll down
coil spring
coil spring
6. Roll up coil spring
7. Place paper bag into outer bag
NOTE: Be certain there are no folds at the top or bottom of
the paper bag
8. Lift zipper
Disposable Dust Bag
(optional)
Our high fi ltration bag is a two-layer, disposable bag that combines
our standard paper bag with a non-woven air fi lter inside. Use a
Filteraire dust bag to create a cleaner indoor environment because
the bag fi lters better than our standard bag. The bags are available
(three in a package) from your local dealer, or you can call 1-800-
282-2886 for other locations.
Look for the symbol.
Ask for GENUINE EUREKA dust bags–Style F & G, PN 57695A.
Brush Roll
The rotating brush roll sweeps and combs the carpet nap.
Keep the brush roll free from hair and threads so it will continue
brushing. When the bristles of the brush roll no longer touch
a straight edge held across the bottom plate, the brush roll is
ineffective because the bristles no longer touch the carpet nap.
To maintain the most effective cleaning, order a new wood
brush roll. Replace the brush strips on the metal brush rolls
(refer to appropriate instructions below).
GENUINE
Look for the symbol.
GENUINE
Look for the symbol.
EUREKA PRODUCT
Look for the symbol.
EUREKA PRODUCT
Look for the symbol.
Look for the symbol.

Headlight Bulb
(Standard on most models)
NOTE: Turn off the switch and unplug the electrical cord
before replacing headlight bulb.
Headlight style varies by model. Locate the notches that
release the tabs at either (1) top, (2) side, or (3) bottom of
the lens, as illustrated. Place a screwdriver into one notch;
twist or pry the screwdriver to release the lens. Repeat for
the second notch on the opposite side.
Rotate the bulb socket forward. Push bulb in and turn to
remove. Secure new bulb into socket and rotate bulb socket
backward.
Replace the lens tabs into the top or the bottom of the hood
opening. Rotate lens to position and press down at each
notch until the lens locks into position.
NOTE: Use 25 watt replacement bulb, only.
Ask for GENUINE EUREKA replacement bulb, 40009A.
6
A B C D
F
E
D
F. Slide in new brush strip of same length (rounded end
fi rst). Fit track on either side into brush roll slot. Replace
second brush strip from opposite end of brush roll.
E. Replace shaft.
D. Align indentation on bearing retainer with brush strip on
both ends of brush roll.
C. Position end cap with fl at sides of center hole over fl at
sides of threaded shaft.
B. Tighten locknut.
A. Align holes and secure rubber end cap cover fl at side
against end cap.
A. Remove rubber end cap cover from one end.
B. Unscrew locknut.
C. Remove end cap.
D. Remove bearing retainer.
E. Push shaft through opposite end.
F. Pull out worn brush strip with pliers.
When properly assembled, the brush roll should rotate freely
between the two end caps. Check the condition of the belt;
change if necessary. Replace the brush roll, belt, and bottom
plate (see How To Replace A Worn Belt).
Ask for GENUINE EUREKA replacement brush strip.
12 inch No. 52282; 16 inch No. 52246-1
How To Replace Worn Brush Strips
(chromed steel brush roll)
NOTE: Turn off the switch and unplug the
electrical cord before replacing brush
strips.
New brush strips are supplied in sets of two, one
long and one short. To replace, remove bottom
plate and belt (see How To Change Belt). Then,
grasp center of brush roll and lift to remove.
1
2
3

7
Brush Roll Belt
The brush roll belt on the upright vacuum cleaner drives the
brush to agitate, sweep, and comb the carpet nap. The belt
should be checked regularly to be sure it is in good condition.
Replace the belt if it is stretching, cracking, or slipping. Cut
away any hair or thread wound around the brush roll or the
belt pulley because the buildup could cause the belt to rotate
unevenly.
How To Replace A Worn Belt
NOTE: Turn off the switch and unplug the electrical cord
before replacing belt. Belt pulleys can become
hot during normal use. To prevent burns, avoid
touching the belt pulley when servicing the drive
belt.
IMPORTANT: Improper installation of the brush roll
or brush roll belt could cause carpet or
cleaner damage.
1. Release cam locks.
2. Pull up on belt to rotate it off the motor pulley. Lift up
on brush roll and remove worn belt.
Check for brush wear (see Brush Roll instructions).
3. Place new belt around brush roll.
4. Align brush roll pulley with belt guide.
1
1
3
4
Belt
guide
guide
guide
guide
7
7
Motor
Motor
pulley
pulley
2
GENUINE
EUREKA PRODUCT
Ask for GENUINE EUREKA
replacement belts, No. 52100
Look for the symbol.
GENUINE
Look for the symbol.
GENUINE
Look for the symbol.
9
9
9
9
8
8
Metal Brush Roll only.
Place rubber end cap covers over both end caps (fl at side
against end cap).
Align holes and secure.
5. Slant brush roll forward so end caps are in line with
slots in cleaner base.
6. Push brush roll into base.
7. Place lower side of belt into belt guide and pull to
stretch the belt around the left side of motor pulley.
Rotate pulley to secure belt into groove.
8. Place slots of bottom plate over tabs of cleaner
base.
9. Seat and secure cam locks.
6
5

THE EUREKA
®
HD
® HD ®
2 YEAR LIMITED WARRANTY
WHAT THIS WARRANTY COVERS
Your Eureka HD cleaner is warranted to be free from all defects in material and workmanship in normal use FOR
A PERIOD OF TWO YEARS. The warranty is granted only to the original purchaser of the cleaner. The warranty is
subject to the following provisions.
WHAT THIS WARRANTY DOES NOT COVER
•
Parts of the cleaner that require replacement under normal use, such as bumpers, bags, bristle strips, belts, light
bulbs, hoses, and impellers.
•
Damages or malfunctions caused by negligence, abuse, or use not in accordance with the Ownerʼs Guide.
•
Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts.
WHAT THE EUREKA COMPANY WILL DO
The Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this
warranty. As a matter of warranty policy, the Eureka Company will not refund the consumerʼs purchase price.
WARRANTY REGISTRATION
Please fi ll out and return the warranty registration card accompanying your cleaner.
OBTAINING WARRANTY SERVICE
To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any
Eureka Authorized Warranty Station. You will fi nd the nearest location in the Yellow Pages under “Vacuum Cleaners–
Service and Repair”. Be certain that the Warranty Station is “Eureka Authorized”.
For the location of the nearest Eureka Authorized Warranty Station or for service information, telephone toll free:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to:
USA: CANADA:
Electrolux Home Care Products Electrolux Home Care Products
North America Canada
America,
Consumer Service 866 Langs Drive
P O Box 3900 Cambridge, Ontario N3H 2N7
Peoria, Illinois, 61612, USA
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping
charges to the Eureka Authorized Warranty Station. Return shipping charges will be paid by the Warranty Station. When
returning parts for repair, please include the model, type, and serial numbers from the data plate on the cleaner.
FURTHER LIMITATIONS AND EXCLUSIONS
Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of
MERCHANTABILITY or any warranty for FITNESS FOR A PARTICULAR PURPOSE is limited to the duration of this
warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not
apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided above. IN NO EVENT SHALL
EUREKA BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES THAT YOU MAY INCUR IN
CONNECTION WITH YOUR PURCHASE OR USE OF THE CLEANER. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specifi c legal rights. You may also have other rights which vary by State.
ELECTROLUX HOME CARE PRODUCTS NORTH AMERICA
Bloomington, Illinois 61701

9
Performance
You Expect
Quality
You Demand
REPAIR PARTS LIST
Eureka Heavy Duty
MODEL
HD2094A
Date: April 7, 2004

10

11
HD2094A
1. 53143 SCREW - pkg of 10
2. 38053-2 KNOB
3. 54005-29 HOOD ASSEMBLY
4. 14193-1 LENS
5. 35958A HEADLIGHT SOCKET ASSEMBLY
6. 48815 HEADLIGHT
7. 53238-14 MOTOR MOUNTING SCREW - pkg of 10
8. 54352-3 MOTOR ASSEMBLY
9. 53228-2 SCREW - pkg of 10
10. 55296 WIRE & TERMINAL ASSEMBLY
11. 53213-5 NUT - pkg of 10
12. 53238-13 SCREW - pkg of 10
13. 53140 CLAMP & SCREW ASSEMBLY
14. 36263 WHEEL COVER
15. 54408-5 BASE ASSEMBLY*
16. 24964A-1 CAM (R.H.)
17. 24965A-1 CAM (L.H.)
18. 53118 CAM RIVET - pkg of 10
19. 53133 WASHER - pkg of 10
20. 37590-1 BUSHING BRACKET
21. 53089-1 STRAIN RELIEF BUSHING - pkg of 10
22. 26808-3 SWITCH BUTTON
23. 37989 SWITCH CLIP
24. 60192-1 WIRE SPLICE - pkg of 5
25. 13738-5 SWITCH ASSEMBLY
26. 71146 LIGHT SHIELD
27. 53238-14 SCREW - pkg of 10
28. 53867 AIR SEPARATOR
29. 30517 MOTOR SEAL GASKET
30. 24834A-3 FOOT PEDAL
31. 53097 FOOT PEDAL SPRING - pkg of 10
32. 37034 ADAPTER RETAINER SPRING
33. 53238-11 SCREW - pkg of 10
34. 53160 CABLE CLAMP - pkg of 5
35. 36263 WHEEL COVER
* INCLUDES ITEMS 16, 17, 18 & 19

12

13
HD2094A
1. 28504-1 FURNITURE GUARD
2. 53121 PUSH NUT - pkg of 10
3. 37183 REAR AXLE
4. 53238-11 SCREW - pkg of 10
5. 35947A FRONT AXLE
6. 53892-1 DISTURBULATOR ASSEMBLY*
7. 27144 DISTURBULATOR CAP
8. 38070SV BEARING & RETAINER ASSEMBLY
9. 53167 WASHER - pkg of 10
10. 60161 WHEEL & AXLE ASSEMBLY**
11. 26242-119N REAR WHEEL
12. 53201 AXLE CLAMP - pkg of 10
13. 53076-2 AXLE SPRING - pkg of 6
14. 35859A-1 FRONT WHEEL
15. 52100A BELT - pkg of 2
16. 52282-4 BRISTLE STRIP SET
17. 13236-3 DISTURBULATOR TUBE
18. 26059A CAP COVER
19. 53158 NUT - pkg of 10
20. 37378 SHAFT
21. 25922-1 BOTTOM PLATE ASSEMBLY
* INCLUDES ITEMS 7, 8, 9, 16, 17, 19 & 20
** INCLUDES ITEMS 3 & 11

6
14

15
HD2094A
1. 54352-3 MOTOR ASSEMBLY COMPLETE
2. 20217E RETAINER ASSEMBLY
3. 30478 MOTOR BRUSH ASSEMBLY
4. 54396 MOTOR COVER
5. 54425-3 ARMATURE FAN & BEARING ASSEMBLY*
6. 53088-5 BEARING - pkg of 5
7. 30474A FAN
8. 53441-2 FIELD ASSEMBLY
9. 46713-1 CABLE TIE
10. 54811 WASHER - pkg of 10
11. 53148 FAN WASHER - pkg of 10
12. 37012-2 PULLEY
13. 53138 RETAINER SCREW - pkg of 10
14. 56817 HEX NUT
15. 53222-4 LOCK WASHER - pkg of 10
16. 53219-2 BRUSH SCREW
17. 54169-1 MOTOR BASE ASSEMBLY**
18. 20217E BEARING RETAINER
19. 53088-5 BEARING - pkg of 5
20. 53187-1 RIVET - pkg of 10
21. 53142 ORLO THREAD SCREW - pkg of 10
22. 12988 FAN
23. 53148 FAN WASHER - pkg of 10
* INCLUDES ITEMS 6 & 7
** INCLUDES ITEMS 18, 19 & 20

16

HD2094A
1. 36965-2 UPPER CORD RETAINER
2. 53198-1 HANDLE SCREW & NUT ASSEMBLY - pkg of 6
3. 13521-2 LOWER CORD RETAINER
4. 39630-2 SUPPLY CORD
5. 53238-13 SCREW - pkg of 10
6. 38183-1SV HANDLE SOCKET ASSEMBLY
7. 53213-5 NUT - pkg of 10
8. 53145 BOLT - pkg of 10
9. 25103A-4 HANDLE GRIP
10. 53077 SPRING - pkg of 5
11. 26176-4SV UPPER HANDLE ASSEMBLY*
12. 12637-8 LOWER HANDLE TUBE
13. 53198-1 SCREW & NUT ASSEMBLY - pkg of 6
14. 53238-13 SCREW - pkg of 10
* INCLUDES ITEM 9
17

HD2094A
1. 53469-22 BAG ASSEMBLY
2. 74244 OWNER’S GUIDE
3. 55332A HARDWARE PACKAGE
4. 47722 BAG SPRING
5. 57695A DISPOSABLE BAGS (STYLE F&G) FILTERAIRE - pkg of 3
6. 48410 GARTER SPRING (NOT SHOWN)

Part No. 74244
(4/04)
©2004 Electrolux Home Care Products, Ltd. Printed in U.S.A.