Euro Kitchen Appliances B02 Series User manual

B02 Series
Under cabinet Range Hood
INSTRUCTION MANUAL
www.KitchenHoods.ca
For domestic cooking only
Dear Customer,
!
!
READ AND SAVE THE INSTRUCTIONS

Thank you for purchasing a range hood from www.kitchenhoods.ca!
If you follow the recommendations contained in this Instruction Manual, our
appliance will give you constant high performance and will remain efficient
for many years to come.
CONTENTS
R COMM NDATIONS AND SUGG STIONS
CHARACT RISTICS
INSTALLATION & US
MAINT NANC &CL AN
Product Specification & Technical Parameters
Model B0276RH
， B0290RH
Rated Voltage 120VAC
Rated Power Frequency 60Hz
Light Power 2x35W
Motor Power 150W
Total Power 230W
Motor 1
Parameters of Outlet Adapter 150mm
Dimension (mm) W756 x D535.5x H144.5(for76 model)
W898 x D535.5x H144.5(for90 model)

WARN NG
TO RUDUCE THE R CK OF F RE, ELECTR C SHOCK OR NJURE TO
PERSONS, PLEASE OBSERVE THE FOLLOW NGS:
１． Installation work and electric wiring(including switch location) must be
done by the qualified person(s) in accordance with local applicable
codes and standards, including fire-rated construction.
２． This hood may have sharp edges. Be careful to avoid cuts and abrasions
during installation and cleaning.
３． The hood must be placed at a minimum distance of 77cm from the cook
panel and 77cm from gas cooker.
４． Sufficient air is needed for proper combustion and exhausting of gases
through the chimney of fuel burning equipment to prevent backdrafting.
Follow the heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire Protection
Association, and the American Society for Heating, Refrigeration and Air
Conditioning ngineer(ASHRA ), and the local code authorities.
５． Ducted fans must always be vented to the outdoors.
６． This appliance is design to be operated by adults. Children were not
allowed to temper with the controls or play with this appliance.
７． To reduce the risk of fire or electric shock,do not use this fan with any
solid-state speed control device.
８． When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
WARN NG-TO REDUCE THE R SK OF F RE,USE ONLY THE METAL
DUCTWORK.
WARN NG - TO REDUCE THE R SK OF NJURY TO PERSONS N THE
EVENT OF A RANGE TOP F RE,OBSERVE THE FOLLOW NG:
1. SMOTH R FLAM S with a close-fitting lid, cookie sheet, or metal tray,
then turn off the burner, B CAR FUL TO P RV NT BURNS. If the flames
do not go out immediately, VACUAT AND CALL TH FIR
D PARTM NT.
2. N RV R PICK UP A FLAMING PAN-You may be burned.

3. DO NOT US WAT R, including wet dishcloths or towels- a violent steam
explosive will result.
4. Use an extinguisher ONLY if:
1) You know you have a Class ABC extinguisher, and you already
know how to operate it;
2) The fire is small and contained in the area where it started;
3) The fire department is being called;
4) You can fight the fire with your back to an exit.
WARN NG-TO REDUCE THE R SK OF A RANGE TOP GREASE F RE:
1. Never leave surface units unattended at high settings. Boiling cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low
or medium settings.
2. Always turn hood ON when cooking at high heat or when flambeing food
(i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé').
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of
the surface element.
CHARACTER ST CS
Below illustration are the dimension of model B0276RH.Model
B0290RH is identical with B0276RH expect for the width of complete
unit changed from 756mm to 898mm.
Dimension

PART L STS
NSTALLAT ON&USE
NOT : on the stainless hoods, carefully remove the plastic protective film
from exterior of the surfaces of the hood prior to final installation.
Caution: To Reduce Risk of Fire And Electric Shock, nstall
This range hood only with integral Blowers manufactured for
Euro Kitchen Appliances nc. Canada

DESCR T ON/CONNECT ON
This appliance may install in ducting version or filtering version.
DUCT NG VERS ON
１． Determine whether the hood discharge vertically(252 × 80mm or round
duct)or horizontally(252 × 80mm duct).For vertically or horizontally, run
ductwork between the hood location and the roof cap or wall cap. For
best results, use a minimum number of transitions and elbows.
２． Use proper diagram below, for replacement of ductwork and electrical
cutout in cabinet or wall. For a non-ducted version installation, do not
cut a duct access hole.
Warning: to avoid the risk of fire, use only the metal ductwork .
F LTER NG VERS ON
１． The hood discharge kitchen air saturated with odor and fumes passes

it through the grease filters and expels it to the outside through an
outlet pipe. With this version the charcoal filters are not required.
２． No need of plastic or metal duct.
３． Must be install charcoal filter on the hood.
NSTALLAT ON
１． Remove the Aluminum filter from the hood.
２． Remove the bottom cover fixed in place with 3 screws.
３． Remove the Damper/Duct connector and parts bag from inside the
hood.
４
４４
４．
．．
． Filtering version installation only

Remove the Recirculation Plate out of the hood and use sealing plate to
seal the outlet off.
５
５５
５．
．．
． Ducted installation only
Tighten the Recirculation Plate and the outlet with 1 screw.
６
６６
６．
．．
． DUCTED NSTALLAT ON ONLY
Attach 282 × 80mm Damper/Duct connector(if using 282mm × 80mm
duct) or150mm Damper/Duct connector(if using 150mm round duct)
over the Knockout openings
NOT : The 150mm round duct must be squeezed into an oval shape

Damper/Duct connector to connect to the Knockout openings on the hood.
７． Hold the hood in position under the cabinet. For ducted installation,
make sure the damper/duct connector enters ductwork and that the
damper opens and closes freely.
８． Tighten all 4 mounting screws completely to secure the hood to the
cabinet.
９． Connect the house power cable to the range hood wring: BLACK to
BLACK, WHIT to WHIT and GR N or B AR WIR to GR N GROUD
SCR W.
１０． Reinstall the

Bottom Cover to the hood.
１１． Install the Halogen lamp.
１２． Replace the filters and turn on the power at service panel and test for
proper operation.
Operation
The hood is operated using a rocker switch on the front panel.
Blower switch
The 3-position blower switch turns the blower ON/OFF and controls the

blower speed.
Set the left side of the switch (0) turns blower on and off.
Set the middle of the switch (1) turns blower on to low speed.
Set the right side of the switch (2) turns blower on/off.
Light switch
The 3-position blower switch turns the lights ON/OFF and controls their
intensity.
Set the left side of the switch (0) turns the lights on and off.
Set the middle of the switch (1) turns the lights on to low intensity.
Set the right of the switch (2) turns the lights on to high intensity.
CAUT ON- The unit is for General Ventilating Use Only. Do Not Use To
Exhaust Hazardous Or Explosive Materials And Vapors
MA NTENTANCE&CLEAN
Caution: Unplug or disconnect the appliance from the
power supply before servicing.
GREASE FILTER
* The grease filters should be cleaned frequently (every two months of
operation, or more frequently for heavy use). Use a warm detergent
solution.
* Grease filters are washable.
Remove the grease filters from the hood. Wash the filters, taking care not to
bend them. Allow them to be dry before refitting.
When refitting the filters, make sure that the handle is visible from the
outside.
reinstall the grease filters to the hood.
REC RCULAT ON CHARCOAL SHEET(F LTER NG VERS ON)
This charcoal sheet is not washable, can not be regenerated, and should be
replaced approximately every 3 months of operation, or more frequently in
the case of heavy usage.

HOOD CLEAN NG
Stainless steel is one of the easiest materials to keep clean. Occasional care
will help preserve its fine appearance.
Cleaning tips:
* Hot water with soap or detergent is all that is usually needed.
* Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft
cloth to avoid water marks.
* For discolorations or deposits that persist, use a non-scratching household
cleanser or stainless steel polishing powder with a little water and a soft
cloth.
* For stubborn cases use a plastic scouring pad or soft bristle brush together
with cleanser and water. Rub lightly in direction of polishing lines or “ grain”
of the stainless finish. Avoid using too much pressure that may mar the
surface.
* Do not allow deposits to remain for long periods of time.
* Do not use ordinary steel wool or steel brushes. Small bits of steel may
adhere to the surface causing rust.
* Do not allow salt solutions, disinfectants, bleaches, or cleaning compounds
to remain in contact with stainless steel for extended periods. Many of these
compounds contain chemicals that may be harmful. Rinse with water after
exposure and wipe dry with a clean cloth.
* Painted surfaces should be cleaned with warm water and mild detergent
only.
Manufactured for:
Euro Kitchen Appliances Inc.
Burnaby, BC Canada
www.KitchenHoods.ca
tel.[phone]