Eurolux EL-B3015 User manual
Owner’s Manual
COOL TOUCH ELECTRIC WATER KETTLE
pg 1
Model#: # EL-B3015 Supply Voltage: 120V, 60Hz
Rated Power: 1500 W Max Capacity: 1.5 L
SPECIFICATIONS
FEATURES
Spout
Handle
Kettle
Lid
Power
Cord
Base
Water
Level
Unlocking
Buttons Display
Panel Keep
Warm
Temp.
Control
On/O
pg 2
IMPORTANT SAFEGUARDS
This appliance is for HOUSEHOLD USE ONLY.
When using an electrical appliance, basic safety precautions should always
be taken, including the following:
1. READ ALL INSTRUCTIONS BEFORE USE.
2. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking o parts, and before cleaning appliance.
3. Do not touch hot surfaces. Use handle.
4. To protect against re, electric shock and injury to persons, DO NOT
IMMERSE CORD, PLUG OR BASE UNIT in water or other liquids.
5. Close supervision is necessary when any appliance is used by or near
children.
6. Do not operate any appliance with a damaged cord or plug, or aer the
appliance has malfunctioned or has been damaged in any way. Return
appliance to the nearest authorized service facility for examination, repair
or adjustment.
7. The use of accessory attachments not recommended by the
manufacturer may result in re, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let power cord hang over edge of table or counter, or touch hot
surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. To disconnect, press the ON/OFF button, then remove plug from wall
outlet.
12. Do not use appliance for anything other than intended use.
13. Scalding may occur if the lid is opened during the heating cycle.
14. Ensure lid is securely closed before serving any beverages.
15. The kettle must never be used on a range top.
16. Do not set a hot container on a wet or cold surface.
17. Do not use a cracked container or a container having a loose or weakened
handle.
18. Do not clean container with cleansers, steel wool pads, or other abrasive
material. This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
t into a polarized outlet only one way. If the plug does not t fully into
the outlet, reverse the plug. If it still does not t, contact a qualied
electrician. Do not attempt to modify the plug in any way.
SAVE THESE INSTRUCTIONS
pg 3
BEFORE YOUR FIRST USE
1. Clean the kettle by lling with water up the MAX mark and boiling it (see
Section below).
2. Pour the water away for hygiene reasons.
3. Repeat the procedure 2x.
4. Remove the kettle from the packaging and carefully remove all packaging
material.
5. Check the kettle and base for possible transport damage.
6. Unwind the power cable from the cable winder. This is on the underside
of the base.
7. Lead the cable through one of the cable recesses.
8. Place the base on an even and stable surface. This surface should be easy
to clean, brightly lit and easily accessible.
9. Place the kettle on the base.
10. Insert the power plug into a socket with protective contacts.
USE OF THE KETTLE
PRIOR TO BOILING WATER
1. Press the KEEP WARM button.
2. Press the SET TEMP button repeatedly until the appropriate temperature
digits on DISPLAY PANEL illuminates in the operating panel.
3. Press the ON/OFF button in order to start the boiling and subsequent
keep-warm process. The digits on the DISPLAY PANEL of the relevant
temperature, and the KEEP WARM button will illuminate. The water is
heated and then the keep warm function will activate.
During boiling:
1. Proceed as described in the “Boiling water” section on the following page.
2. Press the KEEP WARM button during boiling. After the water has boiled,
the digits on DISPLAY PANEL of the relevant temperature will illuminate,
and the KEEP WARM button will illuminate.
pg 4
The water will continue to be kept warm after heating.
BOILING WATER:
CAUTION: The kettle becomes hot during use. Burn hazard! Only hold the
handle. Hot water vapor escapes during heating and boiling. Scalding risk
if touched! Close the lid prior to switching the appliance on. Otherwise, the
appliance cannot switch off automatically and the hot water can over boil.
1. Remove the kettle from the base for filling.
2. Press the locking button for the lid (covered) in order to open the lid. Flip
the lid up. If you push the lid back slightly, it will lock in lightly and will not
shut again unintentionally.
3. Fill the required quantity of fresh, cold water. Pay attention to the fill level
display: The water level must be between MIN and MAX.
4. Close the lid again. Ensure that the lid audibly locks in.
5. Place the kettle on the base.
6. Press the ON/OFF button. Note: if you only intend to boil the water (212°
F ) there is no need to set the temperature, the water will automatically
be programmed to boil.
TO SET TEMPERATURE:
- Press the SET TEMP button repeatedly until the appropriate temperature
digits on DISPLAY PANEL illuminates in the operating panel. The
following 6 temperates can be selected: 212°, 200°, 190°, 185°, 175°, 160° F
- Press the ON/OFF button within 10 seconds. The selected temperature
digits on DISPLAY PANEL will flash. If the boiling procedure is not started
within 10 seconds, the set temperature will be lost and the procedure
must be repeated.
ONCE THE SELECTED TEMPERATURE IS REACHED:
- a signal tone sounds,
- the relevant temperature digits on DISPLAY PANEL illuminates for
another approx. 2 minutes,
7. Remove the kettle from the base. Only hold the kettle by the handle and
wait a moment, until the water is no longer bubbling.
8. Pour the water out slowly. Do not open the lid for this. Note: If you
have set the temperature to e.g. 212° as the required temperature, the
temperature digits on DISPLAY PANEL for 160°, 175°, 185°, 190°, 200°, 212° will
illuminate consecutively during the boiling procedure until the relevant water
pg 5
temperature has been reached. You can stop the boiling procedure at any time
by pressing the ON/OFF button.
KEEP WARM FUNCTION
• With a temperature of 212°, 200°, 190°, 185°, 175° ,160° you can keep the
water warm for kettle switches off automatically; three signal tones will
sound and LED, DISPLAY PANEL will extinguish.
• If you have set a keep-warm temperature of 212 , the water will be
kept warm within a range of 194-212° , in order to avoid excess steam
generation.
• If you have set a keep-warm temperature of 212°, 200°, 190°, 185°, 175°
,160° the water kettle will keep the temperature within a range of approx.
46.4° below/above the set temperature. Note: Only use the keep-warm
function if a minimum of 0.5 liters of water is in the kettle. Otherwise, the small
amount of water could boil away during the next 30 minutes and the dry-run
protection will switch the appliance off.
• If you cannot set a temperature, it is probably because the water
temperature in the kettle is still higher than the desired temperature.
• The keep-warm function can be activated before, during and directly after
boiling water.
• Memory function allows the kettle to be removed from the base without
Losing Its Preset Temp Settings at least 90s
AFTER BOILING
1. Press the KEEP WARM button as soon as the signal tone sounds at the
end of the boiling process. The appliance will automatically select the
temperature to which you have heated the water as the keep-warm
temperature.
2. The digits on the DISPLAY PANEL of the relevant temperature will
illuminate, the KEEP WARM button will illuminate. The water will be kept
warm.
DRYRUN PROTECTION
A dry-run protection safeguards the appliance from damage. The protection
switches on automatically if no more liquid is in the kettle. Note: The dry-run
protection should only be used as a safety device. It is not intended to be part of
the normal operating procedure for the appliance.
IF THE DRYRUN PROTECTION HAS BEEN ACTIVATED
1. Disconnect the power plug from the socket.
2. Allow the kettle to cool o. You can then ll the kettle with water again
and use as usual
pg 6
CLEANING & MAINTENANCE
Always make sure the kettle is unplugged and powered o before storing away
or cleaning. Make sure the unit has cooled down completely before cleaning.
The base, kettle and power cable must not be immersed in water or other liquids.
Electrical shock hazard!
1. Always allow the entire unit to cool completely before cleaning.
2. Wipe the outside of the kettle with a damp cloth. Wipe the base, and cord
with a damp cloth.
3. Open the lid and remove the sieve that is fastened in front of the spout.
For this, press the sieve down slightly and then fold it o. The sieve pre-
vents lime scale deposits and dirt particles from being poured out.
4. Rinse the sieve under running water or clean it using a damp cloth.
5. Reinsert the sieve into its holder in front of the spout. Ensure that it locks
in securely. If the sieve is already very calcied, place it into a mixture of
water and vinegar (6:1 ratio) for a few hours. Aerwards, rinse the sieve
with plenty of clear water.
DESCALING
You should descale the kettle on a regular basis, as a much calcied kettle
requires more electricity. How oen the appliance needs descaling will
depend on the hardness of the water used and frequency of use.
• With normal use, you should descale the kettle every 3 months with so
water and 1x per month with hard water.
• You should descale the appliance regularly to avoid thick calcication
forming on the heating element in the kettle. You can obtain information
about the water hardness in your area from the local water authority. For
descaling, you can use commercially available descaler (pay attention to
manufacturer instructions) or mix household vinegar with water in a 1:1
ratio.
1. Fill the kettle with descaling liquid and boil it.
2. Aerwards, leave the liquid to take eect, for approx. half an hour.
3. Where thick calcication is present: Boil the descaling liquid a second
time. Then, pour it away.
4. Rell the kettle with fresh water, boil the water and also pour it away.
Aerwards, you can use the kettle as usual.
105 Pleasant Avenue Upper Saddle River NJ 07458
201.785.8840 | sales@royaluxusa.com
V8.16
Table of contents
