Eurolux C552 User manual
LED Ceiling Light
C552: Including 1 x 18W Replaceable LED 220 - 240V
C553: Including 1 x 24W Replaceable LED 220 - 240V
ILLUSTRATIONS
C552 / C553
PRODUCT CODE
Cape Town - 9 Racecourse Road, Milnerton, 7441
Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065
www.eurolux.co.za
Please read instructions before commencing installation and retain for future reference.
Step 1 Step 2 Step 3
Step 4 Step 5
Step 6
Instructions
∙ Installation and connection of ceiling light must done by a qualied electrician.
∙ LED ceiling light intended for indoor use.
∙ Recommended mounting height is 2.3m to 3.8m.
∙ LED ceiling light is a Class 2 product, no need for grounding wire.
How to install
Parts
Switch o power
Switch power on
Rotate cover counterclockwise
to remove the cover
connect the lamp to the
light circuit.
Twist the lid clockwise to close.
Choose the right location
Drill holes in the ceiling, and
x the lamp base with screws.
ENVIRONMENTAL PROTECTION
Waste electrical & Electronic equipment regulations requires that any of our products
showing this marking must not be disposed of with other household or commercial
waste. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate any such products from other waste types and recycle
it responsibly at your local facilities.
• Fitting material: LED Ceiling light with Opal PMMA Acrylic lens.
• Class: Class2
• IP Rating: IP 20
• Voltage: 220V - 240V ~ 50Hz
• Commercial / domestic use
• Dimensions: (C552) - (Ø)285mm x (D)85mm / (C553) - (Ø)325mm x (D)85mm
• Lamp type: C552 - Including 1 x 18W Replaceable LED 220 - 240V
C553 - Including 1 x 24W Replaceable LED 220 - 240V
• Replaceable LED Modules available:G1016 - 12W Cool & Warm White
G1017 - 18W Cool & Warm White
G1018 - 24W Cool & Warm White
SPECIFICATIONS
CLEANING
•Beforecleaningalwaysensurethepowersupplyisturnedo.
• Do not immerse the luminaire in water.
• No abrasive products, solvents, detergent may be used to clean this luminaire.
• Ensure that the luminaire does not come in contact with corrosive chemicals, etc.
• Coastal areas ensure that the luminaire is cleaned fortnightly.
Attachments:
Iftheexternalexiblecableorcordofthisluminaireisdamaged,itshouldbeexclusivelyreplaced
bythemanufacturerorhisserviceagentorasimilarqualiedpersoninordertoavoidahazard.
To ensure that you get maximum longevity and maximum use out of your luminaire, please
observe the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire
mustbecarriedoutbyaqualiedelectrician,inaccordancewithSANS10142.Oncompletion
ofinstallation,ensurethattheCerticateofComplianceisupdated.
• Before connecting this luminaire, ensure that voltage indicated on the rating label corresponds
with the mains voltage in your home.
• Whenchangingthelamp,ensurethatthepoweristurnedo.
• This luminaire is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons,
caused by the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a professional
electrician or your supplier for assistance.
• Ensure all items / components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, i.e using silicon sealers or incorrect cabling, will invalidate your
warranty.
• When the cover is damaged, it should be replaced immediately. The luminaire must not be used
without the cover.
• Please check whether the connection of the power cord is safe and reliable before installation.
• Always ensure that the mains supply voltage is correct.
• Always replace the lamp with one of an identical rating.
• The LED Module is replaceable.
IMPORTANT SAFEGUARDS
•Beforeinstallationalwaysensurethepowersupplyisturnedo.
•Thisluminaireisonlysuitableforxedmounting.
• Not for use outdoors or in areas exposed to moisture
• Insert masonry plugs into the mounting surface. Test to ensure the mounting surface will hold the
weightofthetting.
• Connect main supply into terminal block making sure all connections are tight.
• Fit ceiling plate onto mounting surface with self-tapping screws.
•Fitlamprmlyintolampholder.
• Make sure all connections are tight.
• Fit glass shade onto ceiling plate by securely placing it into mounting clips.
• Reconnect power supply.
INSTALLATION
• Ensure that you do not place the luminaire near any combustible materials and / or surfaces.
• Choking hazard: May contain small parts. Keep away from children.
• Donotinsertyourngersoranypartofyourbodyintotheelectricalcontactandsocketsofthis
product whilst it is connected to the electricity supply.
• Item may vary slightly from the picture on the carton.
• Coastalhumiditymayeectthelongevityoftheluminaire.
This manual suits for next models
1
Other Eurolux Lighting Equipment manuals
