Eurolux EA-G9618/SC User manual

Up-facing Floor Lamp
Including: 1 X R7s QI maximum 300W
ILLUSTRATIONS
MODEL
MODELMODEL
ENVIRONMENTAL PROTECTION
Waste electrical & Electronic equipment regulations requires that any of our products showing this mark-
ing must not be disposed of with other household or commercial waste. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate any such products from
other waste types and recycle it responsibly at your local facilities.
FL13SC
EA-G9618/SC
PRODUCT CODE
MODEL
Cape Town - 9 Racecourse Road, Milnerton, 7441
Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065
www.eurolux.co.za
Please read instructions before commencing installation and retain for
future reference.

• Fitting: Steel body with frosted glass.
• Lamp type: Including: 1 X R7s QI maximum 300W.
• Protection against electric shock: Class 2. Does not require earth connection.
• IP: 20. Protected against solid foreign objects of 12.5mm Ø and greater, not
protected against water.
• Not for outdoor use.
• Maximum Ambient temperature range: 20ºC - 40ºC.
• Dimensions: (H)1805mm X (W)320mm x (D) 320mm.
FL13SC - attachments:
If the external exible cable or cord of this luminaire is damaged, it should be exclusively
replaced by the manufacturer or his service agent or a similar qualied person in order
to avoid a hazard.
To ensure that you get maximum longevity and maximum use out of your luminaire,
please observe the following safety instructions.
Electrical products can cause death, injury, or damage to property.
Installation of the luminaire must be carried out by a qualied electrician, in accordance
with SANS 10142. On completion of installation, ensure that the Certicate of
Compliance is updated.
• Before connecting the luminaire, ensure that voltage indicated on the rating label
corresponds with the mains voltage in your home.
• When changing the lamp, ensure that the power is turned off.
• Ensure that the correct lamp type and wattage is tted.
• This luminaire is checked in full for conformity to the quality standards and safety
requirements.
• The manufacturer / supplier is not responsible for any damage of properties and
persons, caused by the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a
professional electrician or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, I.E. Using silicon sealers or incorrect cabling, will
invalidate your warranty.
• When the protection glass is damaged, it should be replaced immediately. The
luminaire must not be used without the protection glass.
• Please check whether the connection of the power cord is safe and reliable before
installation.
• If your mains wiring differs in any way from diagram luminaire, consult a qualied
electrician.
• Always ensure that the mains supply voltage is correct.
• Always replace the lamp with one of an identical rating and wattage.
• Choking hazard: May contain small parts. Keep away from children.
• Do not insert your ngers or any part of your body into the electrical contact and
sockets of this product whilst it is connected to the electrical supply.
• Item may vary slightly from the picture on the carton.
• Coastal humidity may effect the longevity of the luminaire.
• Outdoor luminaires must be cleaned to prevent rust occurring.
SPECIFICATIONSIMPORTANT SAFEGUARDS
INSTALLATION
CLEANING
• Before cleaning always ensure the power supply is turned off.
• Do not immerse the luminaire in water.
• No abrasive products, solvents, detergent may be used to clean this luminaire.
• Ensure that the tting does not come in contact with corrosive chemicals, etc.
• Before installation always ensure the power supply is turned off.
• Unpack and and assemble luminaire on a sturdy surface.
• Screw in the stem of lamp as per steps 1, 2 and 3.
• Pull out the power cord as per step 4.
• Screw in the lamp shade as per step 5.
• Secure power cord into place as per step 6.
• Insert lamp as per step 7. and fasten into place as per step 8 and 9.
• Insert the lamp into the lamp holder.
• Plug into the electrical outlet.
• To switch the lamp on: Set the On/Off switch to (ON) position.
• To switch the lamp off: Set the On/Off switch to (OFF) position.
• Before unplugging the oor lamp from the power supply set the On/Off switch to
(OFF) position.
• Before replacing the lamp always unplug the oor lamp from the power supply
and allow to cool down.
• Ensure that the correct lamp type and wattage is tted.