Euromaid COND6KG User manual

Dryer
COND6KG

Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and passed through
a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and keep it for
future reference.
This User Manual will
• Help you use your machine in a fast and safe way.
• Read the User Manual before installing and starting your product.
• In particular, follow the instructions related to safety.
• Keep this User Manual within easy reach for future reference.
• Please read all additional documents supplied with your product.
Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
A Important safety information. Warning for hazardous situations with regard to
life and property.
BCaution; Warning for supply voltage.
Caution; Warning for fire hazard.
Caution; Warning for hot surfaces.
Read the instructions.
C Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect the environment
by dropping it off in the municipal receptacles provided for this purpose. Your appliance
also contains a great amount of recyclable material. It is marked with this label to indicate
the used appliances that should not be mixed with other waste. This way, the appliance
recycling organised by your manufacturer will be done under the best possible conditions,
in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment. Contact your town hall or your retailer for the used appliance collection points
closest to your home. We thank you doing your part to protect the environment.
COND6KG/121211.0928

3EN
1Important safety information
This section includes safety information that will
help protection from risks of personal injuries
or materialistic damages. Failure to follow
these instructions shall cause any warranty and
reliability commitment to become void.
General safety
• Never place the machine on a carpet-
covered floor, otherwise, lack of airflow
beneath the machine may cause electrical
parts to overheat. This will cause problems
with your machine.
• If the power cable or mains plug is
damaged, you must call Authorised Service
Agent for repair.
• The product should not be plugged in
during installation, maintenance and repair
works. Such works should always be made
by the technical service. Manufacturer
shall not be held responsible for damages
arising from processes carried out by
unauthorised persons.
• Connect the product to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table.
• Operate your product at temperatures
between +5°C and +35°C.
• Do not use electrical devices in the
product.
• Do not connect the air exit of the product
to the chimney holes which are used for
the exhaust fumes of the devices operating
with gas or other types of fuel.
• You must provide enough ventilation in
order to prevent gases exiting from devices
operating with other types of fuels including
the naked flame from accumulating in the
room due to the back fire effect.
• Always clean the lint filter before or after
each loading.
• Never operate your dryer without the lint
filter installed.
• Do not allow fibre, dust and dirt
accumulation around the exhaust exit and
at adjacent areas.
• Power cable plug must be within easy
reach after installation.
• Do not use extension cords, multi-plugs
or adaptors to connect the dryer to power
supply in order to decrease the risk of
electric shock.
• Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a
qualified electrician change the socket with
a suitable one.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
• Do not dry items cleaned with industrial
chemicals in the dryer.
• Do not dry unwashed items in the dryer.
• Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
• Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
• Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
• This product must be grounded.
Grounding installation decreases the risk of
electric shock by opening a path with low
resistance for the electricity flow in case of
a malfunction or failure. Power cable of this
product is equipped with a conductor and
a grounding plug that allows for grounding
the product. This plug must be installed
appropriately and inserted into a socket
which is grounded in accordance with the
local laws and regulations.
• Do not install the product behind a door
with a lock, sliding door or a door that has
a hinge against the hinge of the dryer.
• Do not install or leave this product in
places where it will be exposed to outdoor
conditions.
• Do not tamper with the controls.
• Do not perform any repair or part replacing
procedures on the product even if you
know or have the ability to perform unless
it is clearly suggested in the operating
instructions or the published service
manual.
• Inside and exhaust duct of the product
must be cleaned by the qualified service
personnel periodically.
• Wrong connection of grounding conductor
of the product can cause electric shock. If
you have any suspect about the grounding
connection, have it checked by a qualified
electrician, service representative or service
personnel.
• Do not reach into the machine when the
drum is spinning.
• Unplug the machine when it is not in use.
• Never wash down the appliance with

4EN
water! There is the risk of electric shock!
Always disconnect by unplugging from the
mains before cleaning.
• Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out by grabbing the plug only.
Do not operate the machine if the power
cable or plug is damaged!
• Never attempt to repair the machine
yourself, otherwise, you will be putting your
life and others’ lives in danger.
• For malfunctions that cannot be solved by
following the information given in the safety
instructions:
Turn off the machine, turn off and contact
an authorised service agent.
• Do not stop the dryer before the drying
cycle comes to an end unless you will
remove all laundry from the dryer fast in
order to lay them and dissipate the heat.
• Remove the door of the drying
compartment before decommissioning or
disposing of the product.
• The final step of the drying cycle (cool-
down cycle) occurs without applying
heat to ensure that the items are left at a
temperature that will not damage them.
• Fabric softeners or similar products should
be used as specified by the fabric softener
instructions.
• Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result if
metal reinforcements come loose during
drying.
• Check all garments for forgotten lighters,
coins, metal pieces, needles, etc. before
loading.
• Remove all objects from pockets such as
lighters and matches.
• At times when your dryer is not in use or
after the laundry is taken out following the
completion of drying process, turn off by
using the On/Off button. In cases when
the On/Off button is on (while the dryer
is energized), keep the door of the dryer
closed.
Intended use
• This product has been designed for
domestic use. It should not be used for
other purposes.
• Use the product only for drying laundry
that are marked accordingly.
• Dry only those articles in your product that
are stated in this manual.
• This product is not intended to be used by
persons with physical, sensory or mental
disorders or unlearned or inexperienced
people (including children) unless they
are attended by a person who will be
responsible for their safety or who will
instruct them accordingly for use of the
product.
Children’s safety
• Electrical appliances are dangerous for
the children. Keep children away from the
machine when it is operating. Do not let
them tamper with the machine.
• Packaging materials are dangerous to
children. Keep the packaging materials out
of reach of children or dispose them by
classifying according to waste directives.
• Do not allow children sit/climb on or enter
in the product.
• Children should be supervised to ensure
that they do not play with the product.
• Close the loading door when you leave the
area where the product is located.

5EN
2Installation
Refer to the nearest Authorised Service Agent
for installation of your product.
CPreparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections must
be carried out by a qualified personnel.
APrior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
Appropriate installation location
• Install the product in an environment which
has no risk of freezing and is in a stable
and level position.
• Operate your product in a well ventilated,
dust-free environment.
• Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden bands.
• Do not place your product on a long pile
rug or on similar surfaces.
• Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
• Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
BDo not place the product on top of the
power cable.
• Keep at least 1.5 cm distance to walls of
other furniture.
Under counter installation
• A special part (Part no: 295 970 0100)
replacing the top trim must be provided
and installed by the Authorised Service
Agent in order to use the machine under a
counter or in a cupboard. It should never
be operated without the top trim.
• Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or in
a cupboard.
Mounting over a washing machine
• A fitting device should be used between
the two machines when installing above a
washing machine. The bracket (Part no.
296 280 0100 white/296 280 0200 grey)
must be installed by the Authorised Service
Agent.
• Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the
load on it!
Adjusting feet
In order to ensure that your product operates
more silently and vibration-free, it must stand
level and balanced on its feet. Front feet of your
product can be adjusted. Balance the machine
by adjusting the feet.
1. Loosen the feet by hand.
2. Adjust the feet until the product stands level
and firmly on the floor.
CDo not use any tools to loosen the
adjustable feet, otherwise, they can be
damaged.
CNever remove the adjustable feet from their
housings.
2 plastic pieces supplied along with the user
manual prevent your machine from slipping on
wet and slippery surfaces. To install the plastic
parts:
1. Tilt your product to backwards.
2. Fit the plastic parts on to the front
adjustable feet. Press on the plastic parts
to snap them into their seating.
3. Check the balance of your product
again and readjust the adjustable feet if
necessary.
Electrical connection
Connect the machine to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table. Our
company shall not be liable for any damages
that will arise when the machine is used on a
circuit without grounding.
• Connection must comply with national
regulations.
• If the current value of the fuse or breaker
in the house is less than 16 Amps, have a
qualified electrician install a 16 Amp fuse.
• Power cable plug must be within easy
reach after installation.
• The voltage and allowed fuse or breaker
protection are specified in the “Technical
Specifications” section.
• The specified voltage must be equal to
your mains voltage.
• Do not make connections via extension

6EN
Technical Specifications
EN 2
Height (adjustable) 85.0 cm
Width 59.5 cm
Depth 54 cm
Capacity (max.) 6 kg
Weight (net) 37 kg
Voltage
See type labelRated power input
Model code
Type label is located behind the loading door.
cables or multi-plugs.
• The main fuse and switches must have a
contact distance of minimum 3 mm.
BDamaged power cable must only be
replaced by a qualified electrician.
BIf the product is faulty, it must not be
operated unless it is repaired! There is the
risk of electric shock!
First use
• To have the product ready for operation
before calling the authorised service agent,
make sure that its location and power
supply installations are appropriate. If they
are not, call a qualified electrician to have
any necessary arrangements carried out.
• Make sure that the power connections of
the product are in accordance with the
instructions given in relevant chapters of
this manual.
Disposing of packaging material
Packaging materials are dangerous to children.
Keep packaging materials in a safe place out
of reach of children. Packaging materials of
your product are manufactured from recyclable
materials. Sort and dispose of them in
accordance with recycled waste instructions.
Do not dispose of them with normal domestic
waste.
Transportation of the machine
1. Unplug the machine from the mains.
2. Remove the water drain (if any) and
chimney connections.
3. Drain water remained in the machine
completely before transportation.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how to
dispose of your machine.
Before disposing of your old machine, cut off
the power cable plug and make the loading
door lock unusable to avoid dangerous
conditions to children.

7EN
A B C
l mn
o p q
D
Low
Laundry unsuitable for drying in the
machine
• Laundry items with metal attachments
such as belt buckles and metal buttons
can damage your dryer.
• Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping
bags in the dryer.
• Laundry made of delicate and valuable
fabrics as well as lace curtains can be
creased. Do not dry them in the dryer!
• Do not dry items made of hermetic fibres
such as pillows and quilts in the dryer.
• Laundry made of foam or rubber will be
deformed.
• Do not dry laundry containing rubber in the
dryer.
• Do not dry laundry exposed to petroleum,
oil, combustible or explosive agents in the
dryer even if they are washed beforehand.
• Overly wet laundry or laundry with dripping
water must not be put into the dryer.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
• Do not dry items cleaned with industrial
chemicals in the dryer.
• Do not dry your unwashed laundry in the
dryer.
• Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
• Garments or pillows bolstered with rubber
Things to be done for energy saving:
•Make sure that you operate the product
at its full capacity but pay attention to not
exceeding it.
• Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
• Pay attention to dry same types of laundry
together.
• Follow the instructions in the user manual
for programme selection.
• Make sure that sufficient clearance is
provided at the front and rear side of the
dryer for air circulation. Do not block the
grill at the front side of the product.
• Do not open the door of the machine
during drying unless necessary. If you must
certainly open the door, pay attention not
to keep it open for a long time.
• Do not add new (wet) laundry during
drying.
• Lint and fibres released from the laundry to
the air during the drying cycle are collected
in the “Lint Filter”. Make sure that you clean
the filters before or after each drying.
• In models with condenser, make sure that
you clean the condenser regularly at least
once every month or after every 30 drying
cycles.
• In vented models, follow the chimney
connection rules in the user manual and
pay attention to the chimney cleaning.
• Ventilate the room, where the dryer is
located, well during drying.
• “For power saving in models with lamps, at
times when your dryer is not in use, keep
the door closed if the On/Off button is
pressed (if the dryer is energized).”
Laundry suitable for drying in the
machine
CAlways follow the suggestions on the
laundry labels. Dry only the laundry having
a label stating that they are suitable for
drying in a dryer and make sure that you
select the appropriate programme.
3Initial preparations for drying

8EN
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
• Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
• Do not dry the underwear reinforced with
metal parts in the dryer. If these metal
reinforcements loosen and break during
drying, they will damage your dryer.
Preparing laundry for drying
• Check all laundry items before loading
them into the product to make sure that
there are no lighters, coins, metal items,
needles and etc. in their pockets or on any
part of them.
• Fabric softeners and similar products
must be used in accordance with the
instructions of the manufacturer of the
relevant products.
• All laundry must be spun at the highest
spin speed that your washing machine
allows for the laundry type.
• Laundry may be tangled after washing.
Separate your laundry before placing them
into your dryer.
• Sort your laundry according to their types
and thicknesses. Dry the same type of
laundry together. E.g.: fine kitchen towels
and table cloths dry faster than the thick
bath towels.
Correct load capacity
AConsider the information in the “Programme
Selection Table”. Always start the
programme in accordance with the
maximum load capacity.
CAdding laundry to the machine more
than the level shown in the figure is not
recommended. Drying performance will
degrade when the machine is overloaded.
Furthermore, your dryer and your laundry
can be damaged.
CPlace your laundry into the drum loosely so
that they will not get tangled.
CLarge pieces (E.g.: bed sheets, quilt covers,
large tablecloths) may bunch-up. Stop the
dryer 1-2 times during drying process to
separate bunched-up laundry.
Following weights are given as examples.
Home articles Approximate
weights (g)
Cotton quit covers (double) 1500
Cotton quit covers (single) 1000
Bed sheets (double) 500
Bed sheets (single) 350
Large tablecloths 700
Small tablecloths 250
Tea napkins 100
Bath towels 700
Hand towels 350
Garments Approximate
weights (g)
Blouses 150
Cotton shirts 300
Shirts 200
Cotton dresses 500
Dresses 350
Jeans 700
Handkerchiefs (10 pieces) 100
T-Shirts 125
Loading
• Open the loading door.
• Place laundry items loosely into the dryer.
• Push the loading door to close. Ensure that
no items are caught in the door.

9EN
4Selecting a Program and OperatingYour Machine
Control panel
1 2 34
67 5
20 min
40 min
60 min
10 min
On/Off
Ready to Iron
Buzzer
Cancel
Ready to
Iron
Ready to
Wear
DryingClean Filter
Water Tank Full
End/Anticreasing
Cancel
3 sec.
Start/
Pause
Ready to
Iron
Ready to Wear
Ready to
Wear Extra Dry
Freshen Up
Delicates
Cottons
Synthetics
Timer
Programmes
1. Filter cleaning warning light
Warning light turns on when the filter is full.
2. Program follow-up indicator
Used to follow-up the progress of the
current programme.
3. Cancel audio warning
Used to cancel the audio warning given at
the end of the programme.
4. On/Off button
Used to turn on and off the machine.
5. Programme selection knob
Used to select a programme.
6. Start/Pause/Cancel button
Used to start, pause or cancel the
programme.
7. Water tank warning light*
Warning light turns on when the water tank
is full.
* It may change according to the
specifications of your dryer

10 EN
Preparing the machine
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the “On/Off” button.
C Pressing the “On/Off” button does not
necessarily mean that the programme has
started. Press "Start/Pause/Cancel" button
of the machine to start the programme.
Program selection
Decide the appropriate program from the table
below which includes drying temperature in
degrees. Select the desired program with the
program selection button.
Extra dry
Dry at high temperature
only for cotton laundry.
Thick and multi layered
laundry (E.g.: towels,
linens, jeans) are dried in
a way that they do not
require ironing before
placing in the wardrobe.
Ready to Wear
Normal laundry (E.g.:
tablecloths, underwear)
are dried in a way that
they do not require ironing
before placing in the
drawers.
Ready to Iron
Normal laundry (E.g.,
Shirts, dresses) are dried
ready to be ironed.
C For further program details, see, “Program
Selection Table”
Main programs
Depending on the type of textile, the following
main programs are available:
•Cottons
You can dry your durable clothes with this
program. Dries at a higher temperature. It is
recommended to use for your cotton items
(such as bed sheets, quilt cover, underclothing,
etc.).
•Synthetics
You can dry your less durable clothes with
this program. It dries at a lower temperature
compared to the cottons program. It is
recommended for your synthetic clothes (such
as shirts, blouses, synthetic/cotton blended
garments, etc.).
CDo not dry curtains and lace in your
machine.
•Anti-creasing
A 2-hour anti creasing program to prevent
laundry from creasing will be activated if you
do not take the laundry out after the program
has come to an end. This program rotates
the laundry in 10 minutes intervals to prevent
creasing.
Special programs
For special cases, there are also extra programs
available:
CAdditional programs may differ according to
the model of your machine.
•Delicates
You can dry at a lower temperature your very
delicate laundry (silk blouses, fine underwear,
etc.) that are suitable for drying or laundry which
is advised to be hand-washed.
CIt is recommended to use a cloth bag
to avoid certain delicate garments and
laundry from getting creased or damaged.
Take your garments immediately out of the
dryer and hang them after the programme
ends in order to prevent them being
creased.
•Freshen up
Only ventilation is performed for 10 minutes
without blowing hot air. You can air your clothes
that have been kept at closed environments for
a long time thanks to this program to deodorize
unpleasant odors.
•Timer programs
You can select one of the 10 min., 20 min., 40
min. and 60 min. timer programs to achieve the
desired final drying level at low temperatures.
Program dries at the selected time regardless of
the drying level.
Auxiliary function
Cancel Audio Warning
Your machine will send out an audio warning
when the programme comes to an end. If you
do not want to hear this buzzing, you need to
press the “Cancel Audio Warning” button. The
relevant LED will light up when this button is
pressed and an audio warning will not be given
when the programme comes to an end.
CYou can select this function either before or
after the programme starts.
Warning indicators
CWarning indicators may differ according to
the model of your machine.
Filter cleaning
A warning LED will light up to remind filter
cleaning after the programme finishes.
C If the filter cleaning warning LED lights up
continuously, please refer to, “Solution
suggestions for problems”.
Water tank
A warning LED will light up at the end of the
programme or when the tank is full with water.
The machine stops operating when this warning
LED lights up during a programme running. To

11 EN
restart the machine, please drain the water in
the water tank. Press “Start/Pause/Cancel”
button to start the programme after you have
emptied the water tank. The warning LED goes
off and the programme resumes operating.
Starting the Programme
1. Press “Start/Pause/Cancel” button to start
the programme.
2. “Start/Pause/Cancel” button will light up to
indicate that the programme has started.
Progress of programme
Progress of a running programme is shown
through the programme follow-up indicator.
At the beginning of every programme step, the
relevant indicator LED will light up and light
of the completed step will turn off.
“Drying”:
- Drying level will be illuminated during the whole
drying process until the drying degree reaches “
Ready to Iron “.
“ Ready to Iron “:
- Starts to illuminate when the drying degree
reaches “ Ready to Iron “ step and remains
illuminated until the next step.
“ Ready to Wear “:
- Starts to illuminate when the drying degree
reaches “ Ready to wear “ step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the programme comes to an
end and anti-creasing function is activated.
C If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the programme after the
programme has started
You can use this feature after your machine has
started to dry your clothes under higher or lower
temperatures.
For example;
Press and hold the “Start/Pause/Cancel” button
for about 3 seconds to “Cancel” the programme
in order to select “Extra Dry” programme
instead of “Iron Dry” programme.
Select the “Extra Dry” programme by rotating
the programe knob.
Press “Start/Pause/Cancel” button to start the
programme.
CThe programme which is selected first will
go on even if the programme selection
button is moved and another programme
mode is selected while the machine is
operating. You must cancel the ongoing
programe in order to change the drying
programme. (See, Ending the programme
through canceling)
Adding/removing laundry in standby
mode
In order to add or take out laundry after the
start-up of the programme;
1. Press the “Start/Pause/Cancel” button to
switch the machine to “Pause” mode.
Drying process will stop.
2. Open the door at Pause position and close
it again after adding or taking out laundry.
3. Press “Start/Pause/Cancel” button to start
the programme.
CAny laundry added after the drying process
was started may cause the already dried
clothes in the machine intermingle with wet
clothes and the result will be wet laundry
after the drying process is over.
C Laundry may be added or taken out as
much as desired during a drying process,
but as this process will interrupt drying
continuously, it will extend the programme
duration and increase energy consumption.
Therefore, it is recommended to add
laundry before the drying programme is
started.
Child-proof lock
There is a childproof lock to prevent any
programme interruption due to the pressing of
keys while the programme is on. The loading
door and all keys except the “On/Off” key on
the panel are deactivated when the child-proof
lock is active.
In order to activate the childproof lock, press
on the “Start/Pause/Cancel” and “Cancel audio
warning” buttons simultaneously for 3 seconds.
To start a new programme after the programme
is over or to interrupt the programme, the
childproof lock should be deactivated. To
deactivate the childproof lock, press the same
buttons for 3 sec.
C 2 beeps when activating and 1 beep when
deactivating the child-proof lock is heard.

12 EN
Ending the programe through
canceling
The programme which is selected first will keep
on going even if the position of the programme
selection button is changed. A new programme
can be selected and started after “Programme
cancel” is activated in order to change the
drying programme.
To cancel any selected programme;
• Press “Start/Pause/Cancel” button for
about a duration of 3 seconds. The “Filter
cleaning”, “Water tank” and “End/ Anti-
creasing” warning LEDs will light up at the
end of this period for reminding purposes.
AAs the inside of the machine will be
excessively hot when you cancel the
programme while the machine is running,
activate the ventilation programme to cool
it down.
A If the machine is stopped during any drying
programme, and if the position of the
programme selection knob is changed, an
audio signal will be heard (if the “Cancel
audio warning” function is not selected).
The machine will not start even if the “Start/
Pause/Cancel” button is pressed, unless the
programme selection knob is returned to the
initial programme. The paused programme
must be cancelled in order to change the drying
programme.
End of programme
The “End/Anti-creasing”, “Filter cleaning” and
“Water tank” warning LEDs on the programme
follow up indicator will light up when the
programme comes to an end. The door can be
opened and the machine becomes ready for a
second cycle.
Press the “On/Off” button to shut down the
machine.
C A 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry out
after the programme has come to an end.
CClean the filter after each drying (please
see, Filter cleaning).
CDrain the water tank after each drying
(please see, Water tank)

13 EN
5Maintenance and cleaning
Lint filter
Lint and fibres released from the laundry to
the air during the drying cycle are collected in
the “Lint Filter”.
CSuch fibre and lint are generally formed
during wearing and washing.
CAlways clean the filter after each drying
process.
CYou can clean the filter and filter area by
vacuum cleaner.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up and
open the filter.
3. Clean lint, fibre, and cotton raveling by
hand or with a soft piece of cloth.
4. Close the filter and place it back into its
seat.
CClogging may arise on the filter surface
after using your machine for some time; if
this occurs, wash the filter with water and
dry it before using again.
Sensor (models with a sensor)
There are humidity sensors in your dryer that
detect whether the laundry is dry or not.
To clean the sensor:
1. Open the loading door of the dryer.
2. Allow the machine to cool down if drying
has been carried out.
3. Wipe the metal sensors with a soft cloth,
dampened with vinegar and dry them.
CClean metal sensors 4 times a year.
ANever use solvents, cleaning agents
or similar substances when cleaning
since these materials can cause fire and
explosion!
Water tank (Products equipped with a
condenser);
The moisture in the damp laundry is taken
from the laundry and condensed. Drain the
water tank after each drying cycle or during
drying when “Water tank” warning light turns
on.
ACondensed water is not drinkable!
ANever take out the water tank when the
programme is running!
Water tank may be located in two different
places as indicated below, depending on the
model of your dryer.
- Inside the drawer on the panel
- Behind the kick plate cover
If you forget to drain the water tank, your
dryer will stop during the following drying
cycles when the water tank is full and the
“Water tank” warning light will turn on. If this
is the case, press the “Start/Pause/Cancel”
button to resume the drying cycle after
draining the water tank.
To drain the water tank:
1. Carefully remove the water tank by
opening the kick plate cover/pulling the
drawer.
2. Drain the water by opening the water tank
cover.
3. If there is lint accumulation in the water
tank cover, clean it and press to close.
4. Place the water tank into its seat.

14 EN
For the condenser (products with a
condenser)
Hot and humid air in the condenser is cooled
with the cold air from the room. Thus,
the humid air circulating in your dryer is
condensed and then pumped into the tank.
CClean the condenser after every 30 drying
cycles or once a month.
To clean the condenser:
1. If a drying process has been carried out,
open the door of the product and wait until
it cools down.
2. Unlock the 4 condenser locks after
opening the kick plate.
3. Pull out the condenser.
4. Clean the condenser with pressurized
water and wait until the water drains.
5. Replace the condenser with the side of it
labelled with “Top” facing upwards. Lock
the 4 condenser locks. Make sure that
the red lock on the upper right corner is
engaged securely.
6. Close the kick plate cover.
Close properly and
check the locking
latchs?

15 EN
Drying process takes too much time
• Meshes of the filter may be clogged. Wash with water.
Laundry come out wet at the end of drying.
• Meshes of the filter may be clogged. Wash with water.
• Excessive laundry might have been loaded in. Do not overload the machine.
Machine does not switch on or the program does not start. Machine is not activated when set.
• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Program might have not been set or the «Start/Pause/Cancel» button might have not been
pressed. Make sure that the program has been set and it is not in “Pause” mode.
• «Childproof lock» might have been activated. Deactivate the childproof lock.
• The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
Program has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press «Start/Pause/Cancel» button to start the program.
• The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
Laundry has shrunk, become felted or deteriorated.
• A program suitable for the laundry type might have not been used. Dry only the laundry
which is suitable for drying in your machine after checking the labels on your clothes.
• Select a program with suitable low temperature for the laundry type to dry your clothes.
Drum lightning does not come on. (for models equipped with a lamp)
• The machine might have not been started by using the On/Off button. Make sure that the
machine is On.
• Bulb may have blown. Call the authorized service to replace the bulb.
• The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
2 beeps heard when the buttons are pressed or the program selection knob is turned.
• Childproof lock» might have been activated. Deactivate the childproof lock.
• Program selection knob might be turned to an undefined position. Select one of the
defined programs.
“Filter cleaning” light is flashing.
• Filter might have not been cleaned. Clean the cover filter.
“Final / Anti-creasing” LED is on.
• Program has come to an end. Turn off the machine and take out the laundry.
3 beeps are heard when you press the Start/Pause/Cancel button
• The loading door may be ajar. Make sure that the machine is plugged in.
• Make sure that the condenser cover and the red lock is closed securely.
Also for products equipped with a condenser:
“Water tank” warning LED is flashing.
• Water may be full.
• Drain the water in the water tank.
ACall an authorised service agent if the problem persists.
6Solution suggestions for problems