Eusso 5-Port User manual

5/8/16-Port 10/100Mbps
Fast Ethernet Switch
User’s Manual

FCC COMPLIANCE STATEMENT
This equipment generates and uses radio frequency energy and if not installed
and used properly, that is, in strict accordance with the instructions provided with
the equipment, may cause interference to radio and TV reception. The equipment
has been tested and found to comply with the limits for a Class B computing
device in accordance with the specifications in Subpart B of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference in a
commercial environment. However, there is no guarantee that interference will
not occur in a particular installation.
If you suspect this equipment is causing interference, turn your switch on and off
while your radio or TV is showing interference to determine the source of the
interference.
You can try to correct the interference by one or more of the following measures:
1. Reorient the receiving radio or TV antenna where this may be done safely.
2. To the extent possible, relocate the radio, TV or the other receiver away
from the equipment.
3. Plug the computer which has the equipment installed into a different power
outlet so that equipment and the receiver are on different branch circuits.
If necessary, you should consult the place of purchase or an experienced radio/
television technician for additional suggestion.
CAUTION : The phone jack cannot be connected to telephone system.

Contents
Chapter 1 Introduction ....................................1
Chapter 2 Features & Specifications ..............2
Chapter 3 Package Contents ...........................4
Chapter 4 Physical Description .......................5
Chapter 5 Installation ......................................7
Chapter 6 Trouble-shooting ............................8

Congratulations on your purchase of EUSSO’s 5/8/16-port desktop Fast Ethernet
Switch. This high performance switch provides five/eight/sixteen Fast Ethernet ports
to segment network traffic, extend Fast Ethernet connection distance, and convert
data packets between different transmission speeds. Importantly it provide the Auto
MDI/MDI-X function on all of UTP ports, so you don’t worry about whether the
cable is straight or cross-over type that you can easily connect it to the other switch
or hub.
This switch provides five/eight/sixteen shielded RJ-45 ports with 10Base-T/100Base-
TX Auto-negotiation capability. All of UTP ports support full & half duplex modes
which are able to provide 200Mbps of bandwidth, The auto-negotiation function
providing smooth migration from Ethernet to Fast Ethernet.
This switch is typically used to segment network traffics that can improve the
network performance by increasing the total bandwidth as illustrated in Figure 1-1.
This switch utilizes stored-and-forward switching architecture that filters and
forwards data after the complete data packet is received and examined to be free of
errors.
With one set of status LEDs for each individual port, the switch operation status can
be easily monitored. Their slim and compact design allows direct placing on the
desktop or conveniently mounted on the wall or the side of a desk to accommodate
cabling consideration.
Figure 1-1 Increase network bandwidth
100Mbps
100Mbps
100Mbps
100Mbps
200Mbps
POWER
COL/FDX
LNK/ACT
41526378
Fast Ethernet Switch
8-Port10/100Mbps
35
POWER
COL/FDX
LNK/ACT
321456789
16-Port
Fast Ethernet S witch
10/100Mbps
1110 12 13 14 15 16
POWER
COL/FDX
LNK/ACT
321 456789
16-Port
Fast Ethernet S witch
10/100Mbps
1110 12 13 14 15 16
POWER
COL/FDX
LNK/ACT
321456789
16-Port
Fast Ethernet S witch
10/100Mbps
1110 12 13 14 15 16
POWER
COL/FDX
LNK/ACT
321456789
16-Port
Fast Ethernet S witch
10/100Mbps
1110 12 13 14 15 16
1
1Introduction
1

2
2Features & Specifications
(1) Features
Comply with IEEE 802.3 10Base-T Ethernet and 802.3u 100Base-TX Fast
Ethernet Standards.
Simple and economical way to bridge 10Base-T network and 100Base-TX
network.
Easily connect and segment Fast Ethernet hubs or segments.
All of RJ-45 ports support Auto-MDI/MDI-X function
All of RJ-45 ports support 10Base-T/100Base-TX and Full-Duplex /Half-Duplex
Auto-negotiation function.
Support store-and-forward switching architecture.
Slim and Compact design
2

(2) Specifications
Standards : IEEE 802.3 and 802.3u
10/100Mbps Ports :
5 Port switch -- RJ-45 x 5 Auto-MDI/MDI-X
8 Port switch -- RJ-45 x 8 Auto-MDI/MDI-X
16 Port switch -- RJ-45 x 16 Auto-MDI/MDI-X
Switching Architecture : Store and Forward
Filter/Forward Rate : 148,800 packets/sec.
MAC Address :
5 Port switch -- 2K
8 Port switch – 8K
16 Port switch – 8K
Buffer : 5 Port switch -- 128KByte
8 Port switch -- 256KByte
16 Port switch -- 512KByte
Nway Auto-negotiation : all ports
Full-Duplex/Half-Duplex : all ports
LEDs :System LED -- Power
Port LED -- Link/Activity, 100/10M
Dimensions : 5 Port switch -- 127 x 83 x 30 mm / 5.0 x 3.27 x 1.18 in.
8 Port switch -- 187 x 100 x 30 mm / 7.4 x 3.94 x 1.18 in.
16 Port switch -- 290 x 100 x 30 mm / 11.4 x 3.94 x 1.18 in.
Weight : 5 Port switch -- 180g / 0.40lb.
8 Port switch -- 370g / 0.81lb
16 Port switch -- 480g / 1.06lb
Power : 5/8 Port switch -- 12V DC, 0.5A
16 Port switch -- 12V DC, 1A
Operating Temperature : 32-1310F (0-550C)
Operating Humidity : 10-95% (Noncondensing)
Emission : FCC Class B, CE Mark & C-Tick
3

3
3Package Contents
One Fast Ethernet Switch
One external power adapter
User’s manual
POWER
COL/FDX
LNK/ACT
12345
Fast Ethernet Switch
5-Port 10/100Mbps
5-Port Fast Ethernet
Switch
POWER
COL/FDX
LNK/ACT
41526378
Fast Ethernet Switch
8-Port 10/100Mbps
8-Port Fast Ethernet
Switch
POWER
COL/FDX
LNK/ACT
321 456789
16-Port
Fast Ethernet Switch
10/100Mbps
1110 12 13 14 15 16
16-Port Fast Ethernet
Switch
Figure 3-1 Package contents
4

LED Panel
Power LED 100/10Mbps LED
Link/Activity LED
POWER
100M
LNK/ACT
Fast Ethernet Switch 12345
RJ45 Connectors
Power Connector
5-Port 10/100Mbps
4
4Physical Description
(1) Panel
5-Port Fast Ethernet
Switch
Power LED
LED Panel
RJ45 Connectors
Power Connector
POWER
100M
LNK/ACT
Fast Ethernet Switch 41526378
10/100M LED
Link/Activity LED
8-Port 10/100Mbps
POWER
100M
LNK/ACT
31121019412513614715816
Fast Ethernet Switch
LED Panel
RJ45 Connectors
Power Connector
100/10Mbps
Link/Activity LED
Power LED
16-Port 10/100Mbps
8-Port Fast Ethernet
Switch
16-Port Fast Ethernet
Switch
Figure 4-1 Panel description
5

(2) LED
Power is supplied
No power
LED Color Status Description
PWR
(Power) Green Lit
Off
A valid link is established
No link is established
Data packets received
Off
LNK/ACT
(Link/Activity)
SPEED
(10/100M)
Green
Yellow
Lit
Off
Lit This port run at 100Mbps
This port run at 10Mbps
Flash
Table 4-1 LED description
6

5
5Installation
1. Operating Environment
This switching hub must be installed and operated within the limits of specified
operating temperature and humidity (see previous section under Specifications). Do
not place objects on top of the unit. Do not obstruct any vents at the sides of the unit.
Do not position the unit near any heating source such as heater, radiator, or direct
exposure to sun. Prevent entering of water and moisture into the unit. If necessary,
use dehumidifier to reduce humidity.
2. Connecting to network devices
The RJ-45 ports on the switch are supported Auto-MDI/MDI-X function which one
allow using straight-through or cross-over type to connect this switch to workstation
or hub.
Connect one end of the network cable to the RJ-45 port on the rear panel, and
connect the other end of the network cable to the RJ-45 port on the network device.
Follow the same procedure to connect all the RJ-45 ports of the switch. The UTP
network cables must comply with EIA/TIA 568 specifications and Category 5
standard for 100Mbps data transmission. Maximum length, using UTP cable,
between the switch and connected device is 100 meters (300ft). Once the network
cable is connected to both ends and the attached network device is powered on, the
green LNK/ACT LED should be lit.
3. Connecting the power
Connect the output end of the power
adapter to the power connector on the
rear panel of the unit. Connect the
power adapter to the power outlet.
The green Power LED on the front
panel should be lit.
External Power Adapter
DC Power
AC Power
Figure 5-1 Connect the AC power adapter
7

8
6
6Trouble-shooting
1. Power LED is not lit
zCheck if the power cord is properly connected to the external power adapter and
the power outlet. Make sure the DC power jack is firmly plugged into the power
socket of the switch.
2. Link/Activity is not lit when connect to 100Mbps device
zCheck the power switch of the network device attached to the switch; make sure it
is turned ON.
zCheck the network cable; make sure it is properly connected to the switch and the
network device.
zCheck the network cable; make sure the UTP cables comply with EIA/TIA 568
and Category 5 specification.
[!] Contact your dealer if problem persist.