EverFocus EMC920F Series User manual

EMC920F / EMD920F eZ.HD Series
1080p FHD IP67 Mobile IR Mini Camera
User’s Manual
EMD920F
EMC920F
Copyright © EverFocus Electronics Corp.
Release Date: April, 2018
All the images including product pictures or screen shots in this document are for example only. The images
may vary depending on the product and software version. Information contained in this document is
subject to change without notice.

Precautions
1. Do not install the camera near electric or magnetic fields. Install the camera away from TV/radio
transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic
fields generated from these devices may distort the video image or otherwise interfere with camera
operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials
other than those recommended herein. Improper disassembly or introduction of corrosive materials
may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may cause
permanent damage to the sensor and/or internal circuits, as well as creating unbalanced illumination
beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord with wet
hands. Touching a wet power cord with your hands or touching the power cord with wet hands may
result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may result in
equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor directly
with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the
camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use
complex solvents, corrosive or abrasive agents for cleaning of any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.
This camera is suitable for indoor operation only. Use the camera at temperatures within -10°C~50°C
(14°F~112°F) and humidity less than 80%; this device is not rated as submersible. The input power
source is 12VDC. Be sure to connect the proper + / - polarity and voltage, as incorrect polarity or too
high a voltage will likely cause the camera to fail, and such damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of the camera
plus any wind, snow, ice or other loading, and securely attach the camera to the mounting surface
using screws and anchors which will properly support the camera. If necessary (e.g. when mounting to
drop ceilings) use a safety wire to provide additional support for the camera.

Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
ATTENTION! This is a class A product which may cause radio interference in a domestic
environment; in this case, the user may be urged to take adequate measures.
This Product is RoHS compliant.
WEEE
Your EverFocus product is designed and manufactured with high quality materials and components
which can be recycled and reused. This symbol means that electrical and electronic equipment, at
their end-of-life, should be disposed of separately from your household waste. Please, dispose of
this equipment at your local community waste collection/recycling centre. In the European Union
there are separate collection systems for used electrical and electronic product.
Please, help us to conserve the environment we live in!

Contents
1. Introduction...................................................................................................................... 1
1.1 Packing List .....................................................................................................................1
1.2 Features ..........................................................................................................................1
1.3 Dimensions .....................................................................................................................2
1.4 Optional Accessory .........................................................................................................2
2. Cable Description.............................................................................................................. 3
3. Installation........................................................................................................................ 3
3.1 EMD920F ........................................................................................................................3
3.2 EMC920F.........................................................................................................................6
4. Configuration in the OSD Menu......................................................................................... 7
5. Specifications.................................................................................................................. 11

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
1
1. Introduction
Equipped with a 1080p CMOS sensor, the EverFocus eZ.HD series cameras - EMC920F and EMD920F
deliver 1080p full HD image quality. Both of the models provide 2.8mm lens. Featured with Digital
Wide Dynamic Range (D-WDR), the camera can provide clear images even under backlight
circumstances where intensity of illumination can vary excessively.
The EMC920F and EMD920F support both NTSC and PAL scanning systems and are IP67 certified
(non-audio models). The IR LEDs enable night vision up to 10m (~32ft.). The models are designed
with compact size, which is suitable for discreet surveillance. EMC920F and EMD920F are the ideal
solution for your mobile surveillance needs.
EMC920F provides audio and non-audio models; EMD920F does not support audio function.
Model Audio Function Weather Resistance
EMC920F Supported IP67
Not supported
IP67
EMD920F Not supported IP54
1.1 Packing List
EMC920F EMD920F
Camera x 1 Camera x 1
User Manual x 1 User Manual x 1
Screw x 2 Screw x 4
Anchor x 2 Hexagon Wrench x 1
Hexagon Wrench x 1
1.2 Features
1080p Full HD with high flexibility and performance for astounding image
1080p CMOS sensor, delivering amazing high sensitivity
2.8mm lens to capture the desired field of view
Extended IR range up to 10m / 32ft. (depends on IR reflectivity in actual scene)
D-WDR to improve the visibility under high contrast scene
3D-Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio images even
under low light environments
IP67 (non-audio model) rated / IP54 (audio model) rated*

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
2
Compact size for discreet surveillance
eZ Controller function: Control camera OSD settings directly from DVR end
* EMC920F provides audio and non-audio models; EMD920F does not support audio function.
1.3 Dimensions
EMC920F 76mm/3"
69mm/2.7"
78mm/3.1"
EMD920F
1.4 Optional Accessory
RCA Audio-Output Cable M12 Video-Output Cable
EMC920F supports audio and non-audio
function. If audio model is selected, a RCA
Audio-Output Cable will be provided. The
audio model is IP54 rated.
The standard model provides a BNC
video-output cable. You can also optionally
change the BNC video-output cable to M12
video-output cable.

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
3
2. Cable Description
Power Cable
Video Output Cable
1
2
No. Name Descriptions
1 Power Cable Connects to a 12VDC power source.
2 Video Output 1080p output, using a 75 Ohm BNC-type coaxial cable.
3. Installation
3.1 EMD920F
1. Attach the supplied Base Gasket to the mounting surface to mark the four screw holes on the
mounting surface. You can optionally mark a cable hole only if you want to run the cables
through the surface. Drill the marked screw holes and cable hole on the mounting surface.
Base Gasket
Cable Hole
Screw Hole
2. Loosen the four camera cover screws using the supplied Hexagon Wrench and then remove the
camera cover.
3. Place the supplied Base Gasket between the Mounting Surface and Camera Base and then
screw the camera base to the surface using the supplied four Screws. Note that you can either
run the cables through the Cable Hole or through the Side Cut.

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
4
Base Gasket
Mounting Surface
Camera Base
Screw
Side Cut
Cable Hole
4. Connect the Power Cable to a 12VDC power source. Connect the Video Output Cable to a
monitor or DVR.
Power Cable
Video Output Cable
5. To adjust camera tilt angle, loosen the tilt screws on both side of the camera to adjust the tilt
angle by 51°
51°
Tilt Screw

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
5
6. Screw back the camera cover using the supplied Hexagon Wrench.
Cover Screw
Cover Gasket
Camera Base
Camera Cover

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
6
3.2 EMC920F
Screw Hole
Screw Hole
Optionally thread the
cable through this hole
Loosen to adjust Sunshield / Camera Angle
4
5
4Loosen to adjust Sunshield / Camera Angle
Loosen to adjust Bracket Angle
1
1
2
3
Power Cable
Video Output Cable
1. Attach the Camera Bracket to the surface where you want to mount the camera and mark the
Screw Hole locations on the surface. Drill two screw holes on the surface and insert the
supplied two Anchors to the holes. Screw the Camera Bracket to the surface using the supplied
two Screws.
2. Optionally drill another hole in the middle between the two screw holes only if you want to
thread the cables through the surface.
3. Connect the Power Cable to a 12VDC power source. Connect the Video Output Cable to a
monitor or DVR.
4. To adjust the Sunshield or Camera angle, loosen the two screws on both sides and then adjust
the angle.
5. To adjust the Bracket angle, loosen the screw on both sides and then adjust the angle.

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
7
4. Configuration in the OSD Menu
You can configure camera settings in the OSD menu from DVR end. OSD menu structure is listed on
the below table:
No. Main Sub Menu Sub Menu / Function
1 Lens
Manual -
DC Mode
Indoor
Outdoor
Min Shutter 1/3 0
Max
Shutter
1/60, 1/240, 1/480,
1/1000, 1/2000,
1/5000, 1/10000,
1/50000, FLK
IRIS Speed 0-15
2 Exposure
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
AGC 0-15
Sens-up Off
Auto X2, X4, X6, X8, X10, X15, X20, X25, X30
Brightness 1-100 (50 default)
D-WDR
Off
On Level 0-8
Auto
Defog
Off
Auto
Pos/Size Position, Size,↑,↓,→,←
Gradation 0-2
Default
3 Backlight
Off
BLC
Level Middle, High, Low
Area Position, Size,↑,↓,→,←
Default
HSBLC
Select Area1, Area2, Area3, Area4
Display Off
On Position, Size,↑,↓,→,←
Black Mask On/Off
Level 0-100

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
8
Mode All Day
Night AGC Level 0-255
Default
4 White
Balance
ATW
AWC→SET
Special2*
Special1*
Manual Blue 0-100
Red 0-100
AWB
5 Day &
Night
Ext D→N(Delay) 0-60
N→D(Delay) 0-60
Auto
D→N(AGC) 1-255
D→N(Delay) 0-60
N→D(AGC) 1-255
N→D(Delay) 0-60
Color
B/W
Burst Off/On
IR Smart
Off
On
Level 0-15
Area Position,
Size,↑,↓,→,←
IR PWM 0-100
6 NR 2DNR Middle/Low/Off/High
3DNR Middle/Low/Off/High
7 Special
Cam Title
Off
On 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ
▶→←↑↓()ˉ-_▊/=&:~,.
D-effect
Freeze Off/On
Mirror Off, Mirror, V-flip, Rotate
Neg. Image Off/On
Motion
Off
On
Select Area1,Area2,Area3,Area4
Display On Position,
Size,↑,↓,→,←
Off
Sensitivity 0-100

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
9
Color Green, Blue, White, Red
Trans 1.00, 0.75, 0.25, 0.00
Alarm
View Type Off, Block, Outline, All
OSD View On/Off
Alarm Out On/Off
Time 0-15
Default
Privacy
Off
On
Select Area1,Area2,Area3,Area4
Display
Off
Color Position,
Size,↑,↓,→,←
Mosaic Position,
Size,↑,↓,→,←
Inv Position,
Size,↑,↓,→,←
Color White, Black, Red, Blue, CYAN,
Yellow, Green, User
Trans 1.00, 0.75, 0.50, 0.25
Default
Language ENG/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Defect
Live DPC
Off
On AGC level 0-255
Level 0-100
White DPC
Off
On
Pos/Size Position,
Size,↑,↓,→,←
Start Close the iris then
press
DPC View Off/On
Level 0-60
AGC 0-14
Sens-up x2, x4, x6, x8,x10, x15,
x20, x25, x30
Black DPC
Off
On Pos/Siz Position,
Size,↑,↓,→,←

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
10
Start Press Enter
DPC View Off/On
Level 0-100
RS485
CAM ID 0-255
ID Display Off/On
Baud Rate 2400, 4800, 9600, 19200 ,38400
8 Adjust
Sharpness
Off
Auto
Level 0-10
Start AGC 0-255
End AGC 0-255
Monitor
LCD
Gamma User,0.45,0.50,0.55,0.60,0.65,0.70,
0.75,0.80,0.85,0.90, 0.95,1.00
Blue Gain 0-100
Red Gain 0-100
CRT Blue Gain 0-100
Red Gain 0-100
LSC Off/On
Video. Out PAL/NTSC
COMET Off/On
9 Exit Save & END /Reset/Not Save
Note：
- If the Color Temperature of your operation environment only stays around 6500K, you can
select “Special 1” as the White Balance strategy.
- If the Color Temperature of your operation environment only stays around 2800K, you can
select “Special 2” as the White Balance strategy.
- If the Color Temperature of your operation environment varies, or does not stay around 6500K
/ 2800K, please use the default White Balance strategy.

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
11
5. Specifications
Model Name EMC920F EMD920F
Pickup Device 1080p CMOS sensor
Video Format NTSC / PAL (switchable via DVR)
Effective Pixels 1920 (H) x 1080 (V)
Scanning System Progressive Scan
Sensitivity 0 Lux with IR On
Electronic Shutter Auto / Manual (x30 ~ 1/50,000) / FLK
Gamma Correction 0.45
Lens Type 2.8mm
FOV (D x H x V) 131° x 106° x 63°
BLC OFF / BLC / HS BLC Selectable
AGC 0 ~ 15 Levels
White Balance ATW / AWC-SET / Indoor / Outdoor / Manual / AWB
Sync Mode Internal
Day/Night Ext, Auto, Color, B/W
IR LED 18 Units 12 Units
IR Distance Up to 10m / 32ft. (depends on IR reflectivity in actual scene)
OSD Languages
English / Simplified Chinese / Traditional Chinese / German / French /
Italian / Spanish / Polish / Russian / Portuguese / Netherlands / Turkish
DNR
2DNR / 3DNR, Off
DEFOG Off / Auto
D-WDR
On / Off / Auto
Sens-up
Off / Auto (x2 ~ x30)
Mirror Off / Mirror / V-Flip / Rotate
Motion Detection
Off / On (4 selectable zones)
Privacy Mask
Off / On (4 selectable zones)
Audio Output RCA x 1 (Optional) Not supported
Environmental IP67 (non-audio model) /
IP54 (audio model) IP67
Power Source 12VDC
Power Consumption 3.6W 1.8W
Operating Temperature -10°C ~ 50°C / 14°F ~ 122°F
Humidity Less than 80%
Dimensions (L x W x H)
76mm x 78mm x 69mm /
3” x 3.1” x 2.7”
101mm x 101mm x 67mm /
3.98” x 3.98” x 2.64”
Weight 286g / 0.6lb 322g / 0.71lb
Certifications CE, FCC, RoHS

EMC920F/EMD920F eZ.HD Mobile IR Mini Camera
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
[e-mail]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: [phone]
FAX: [phone]
www.everfocus.de
[e-mail]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: [phone]~39
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus China - Shenzhen:
3F,Building 7,Longcheng Industrial
Park,No.440,Longguan Road, Dalang Street,
Longhua, Shenzhen, Guangdong, China
TEL: [phone]
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA
91010, USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[e-mail]
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
[e-mail]
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!