EverFocus eIVP1300 Series User manual

eIVP1300
Intel Atom E3845 / E3825 Mobile Network Video Recorder with 4-
Channel IP Cameras
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: September 2019

EVERFOCUS ELECTRONICS CORPORATION
eIVP1300
Intel Atom E3845 / E3825 Mobile Network Video
Recorder with 4-Channel IP Cameras
User’s Manual
1995-2019 EverFocus Electronics Corp.
www.everfocus.com.tw
Disclaimer
All the images including product pictures or screen shots in this document are for example only. The
images may vary depending on the product and software version. Information contained in this document
is subject to change without notice.
Copyright
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the EverFocus Electronics Corporation.
-Microsoft Windows is a registered trademark of Microsoft Corp.
-Intel, Pentium, Celeron, and Xeon are registered trademarks of Intel Corporation
-Core, Atom are trademarks of Intel Corporation
-ITE is a trademark of Integrated Technology Express, Inc.
-IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
All other product names or trademarks are properties of their respective owners.

ii
Safety Precautions
Please read the following safety instructions carefully. It is advised that you keep this manual
for future references.
All cautions and warnings on the device should be noted.
All cables and adapters supplied by EverFocus are certified and in accordance with the
material safety laws and regulations of the country of sale. Do not use any cables or
adapters not supplied by EverFocus to prevent system malfunction or fires.
Make sure the power source matches the power rating of the device.
Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
Always completely disconnect the power before working on the system’s hardware.
No connections should be made when the system is powered as a sudden rush of power
may damage sensitive electronic components.
If the device is not to be used for a long time, disconnect it from the power supply to avoid
damage by transient over-voltage.
Always disconnect this device from any AC supply before cleaning.
While cleaning, use a damp cloth instead of liquid or spray detergents.
Make sure the device is installed near a power outlet and is easily accessible.
Keep this device away from humidity.
Place the device on a solid surface during installation to prevent falls.
Do not cover the openings on the device to ensure optimal heat dissipation.
Watch out for high temperatures when the system is running.
Do not touch the heat sink or heat spreader when the system is running.
Never pour any liquid into the openings. This could cause fire or electric shock.
As most electronic components are sensitive to static electrical charge, be sure to ground
yourself to prevent static charge when installing the internal components. Use a grounding
wrist strap and contain all electronic components in any static-shielded containers.
If any of the following situations arises, please contact our service personnel
([e-mail]):
-Damaged power cord or plug
-Liquid intrusion to the device
-Exposure to moisture
-Device is not working as expected or in a manner as described in this manual
-The device is dropped or damaged
-Any obvious signs of damage displayed on the device
DO NOT LEAVE THIS DEVICE IN AN UNCONTROLLED ENVIRONMENT WITH TEMPERATURES
BEYOND THE DEVICE’S PERMITTED STORAGE TEMPERATURES (SEE SPECIFICATION) TO
PREVENT DAMAGE.

iii
FCC Statement
This device complies with Part 15 FCC Rules. Operation is subject to the
followi
ng two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received including
interference that may cause undesired operation.
Caution:
There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions and your local government’s recycling or disposal directives.
Attention:
Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.
Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le constructeur.
Recycler les batteries usées en accord avec les instructions du fabricant et les directives
gouvernementales de recyclage.

iv
RoHS Requirements
設備名稱 (Equipment): 網路數位錄放影機，型號（型式）/ Type designation (Type): eIVP1300
單元Ｕnit 限用物質及其化學符號 Restricted substances and its chemical symbols
鉛Lead
(Pb)
汞Mercury
(Hg)
鎘Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
印刷電路板及
電子零組件
PCB & Other
Components
X ○○○○○
外部訊號連接
器及線材
Wires &
Connectors for
External
Connections
X ○○○○○
O：表示該有毒物質在該部件所有均質材料中的含量均在SJ/T 11363-2006標準規定的限量要求以下。
The quantity of poisonous or hazardous substances or elements found in each of the component's parts is
below the SJ/T 11363-2006-stipulated requirement.
X：表示該有毒物質至少在該部件的某一均質材料中的含量超出 SJ/T 11363-2006標準規定的限量要求。
The quantity of poisonous or hazardous substances or elements found in at least one of the component's
parts is beyond the SJ/T 11363-2006-stipulated requirement.
備註： 一、此產品所標示之環保使用期限，係指在一般正常使用狀況下。The Environment Friendly Use
Period as labeled on this product is applicable under normal usage only

v
TABLE OF CONTENTS
1. Introduction ............................................................................................................................ 1
1.1 Features .......................................................................................................................... 1
1.2 Dimensions...................................................................................................................... 2
1.3 Packing List...................................................................................................................... 2
1.4 Front Panel...................................................................................................................... 3
1.5 Rear Panel ....................................................................................................................... 4
2. Connection and Installation.................................................................................................... 5
2.1 Storage Installation ......................................................................................................... 5
2.1.1 Storage Compatibility List ........................................................................................... 6
2.2 DC Out Cable................................................................................................................... 7
3. AMI BIOS Setup....................................................................................................................... 8
3.1 System Test and Initialization ......................................................................................... 8
3.2 AMI BIOS Setup............................................................................................................... 9
3.3 Setup Submenu: Main .................................................................................................... 9
3.4 Setup Submenu: Advanced........................................................................................... 10
3.4.1 Advanced: Power Management ............................................................................... 10
3.4.1.1 Power Management: S5 RTC Wake Settings ........................................................ 12
3.4.2 Advanced: Super IO Configuration ........................................................................... 13
3.4.2.1 Super IO Configuration: Serial Port 1 Configuration ............................................ 13
3.4.2.2 Super IO Configuration: Serial Port 2 Configuration ............................................ 14
3.4.2.3 Super IO Configuration: Serial Port 3 Configuration ............................................ 14
3.4.2.4 Super IO Configuration: Serial Port 4 Configuration ............................................ 15
3.4.2.5 Super IO Configuration: Smart Fan Function........................................................ 17
3.4.2.6 Super IO Configuration: Smart Fan Mode Configuration ..................................... 17
3.4.3 Advanced: Digital IO.................................................................................................. 18
3.4.4 Advanced: H/W Monitor........................................................................................... 19
3.4.5 Advanced: CPU Configuration................................................................................... 19
3.4.5.1 CPU Configuration: Socket 0 CPU Information..................................................... 20
3.4.6 Advanced: IDE Configuration.................................................................................... 20
3.4.7 Advanced: CSM Configuration.................................................................................. 21
3.4.8 Advanced: Trusted Computing ................................................................................. 22
3.4.9 Advanced: USB Configuration................................................................................... 23
3.4.10 Advanced: Touch Device....................................................................................... 24
3.5 Setup Submenu: Chipset............................................................................................... 24
3.5.1 Chipset: Host Bridge.................................................................................................. 25
3.5.1.1 CPU Configuration: Socket 0 CPU Information..................................................... 26
3.5.2 Chipset: South Bridge................................................................................................ 27
3.5.2.1 South Bridge: Azalia HD Audio.............................................................................. 28
3.5.2.2 South Bridge: USB Configuration.......................................................................... 29
3.5.2.3 South Bridge: PCI Express Configuration .............................................................. 30
3.6 Setup Submenu: Security.............................................................................................. 31
3.7 Setup Submenu: Boot ................................................................................................... 32
3.8 Setup submenu: Exit ..................................................................................................... 33
4. Specification.......................................................................................................................... 34

eIVP1300 AI Mobile NVR
1
1. Introduction
The eIVP1300 is one of EverFocus’ eIVP series AI mobile NVRs adopting Intel® Atom™ processor
and Movidius™ Myriad™ X AI core module. The model supports 4 IP cameras, wide operating
temperature ranging from 0°C to 60°C, and wide DC range of DC 9-24V.The eIVP1300 is complied
with the MIL-STD-810G standard for the utmost viability for vehicular use. Besides, the model is
also CE, FCC and RoHS certified. The eIVP1300 AI mobile NVR carries everything you need for
computing on the road.
eIVP1300 Model SKU:
CPU Memory Display Storage LAN USB RS232/48 Power
Atom
E3845 Onboard DDR3L (4GB) HDMI x 1, VGA x 1 optional GbE x 2 USB3.0 x 1
USB2.0 x 3 RS232 x 2 9~24VDC
Atom
E3825 Onboard DDR3L (4GB) HDMI x 1, VGA x 1 optional GbE x 2 USB3.0 x 1
USB2.0 x 3 RS232 x 2 9~24VDC
1.1 Features
•In-vehicle network video recorder platform
•Intel® Atom™ E3845 / E3825 processor
•Onboard DDR3L memory up to 4GB
•Intel® Integrated Graphics Engine supports 2 display outputs by HDMI x 1, VGA x 1
•Intel® I211 (or 210) Ethernet x 2 ports (GbE x 2)
•Supports 4-channel IP cameras
•Supports removable SSD storage (optional)
•Supports 8-bit digital I/O (optional), USB2.0 x 3, USB3.0 x 1
•Supports RS-232 x 2
•Intel® Movidius™ Myriad™ X AI core module (optional)
•Supports CAN Bus 2.0B (optional)
•Wide DC range DC 9-24V
•CE, FCC, RoHS certified
Chapter
1

eIVP1300 AI Mobile NVR
2
1.2 Dimensions
177.8
50.4
211.8
180.3
186.5
Unit: mm
1.3 Packing List
•NVR x 1
•DC Power Terminal Block d x 1
•DC Out Cable x 1 (power supply for
cameras)
•mSATA Screw x 1
•2.5” SSD Screw x 4
•User Manual x 1
• CD x 1 (see Note 3)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your
local EverFocus office or agents for more information. Please also keep the shipping carton
for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. The CD contains the User Manual and some Drivers for the system. If you can’t find the
required drivers from the CD, please go to our website for related
drivers. www.everfocus.com.tw

eIVP1300 AI Mobile NVR
3
1.4 Front Panel
124
3
No. Name Description
1 USB2.0 Ports USB2.0 ports.
2 Reset Press the button to restart the system.
3 Power Button Press the button to turn on or turn off the system.
4 LED Indicator Power: When power is on, the LED will continue lighting in red.
HDD: When storage is reading/writing data, the LED will flashes green.

eIVP1300 AI Mobile NVR
4
1.5 Rear Panel
123451
678910 11
No. Name Description
1 Antenna Connects the antenna to the mobile NVR for 3G / 4G / WiFi functions.
2 VGA Port VGA display output.
3 HDMI Port HDMI display output.
4 WAN/LAN Connects to the Network.
5 USB2.0 Port
USB3.0 Port USB ports.
6 Audio Input
Connects to audio input devices, such as microphones. Note that the
microphones with a (built-in) amplifier and external power supply are
required.
7 Audio Output
Connects to an audio output device, such as speakers. Note that the
speakers with a (built-in) amplifier and external power supply are
required.
8 COM2 RS-232 port.
9 COM1 RS-232 port.
10 Power Output A total of 12VDC, 2A power supply to the connected cameras. Please refer
to 2.2 DC Power Out Cable.
11 Power Input Insert the supplied DC Power Terminal Block and then connect the
system to a DC 9-24V power source.

eIVP1300 AI Mobile NVR
5
2. Connection and Installation
2.1 Storage Installation
The eIVP1300 supports mSATA drive (half size) and 2.5” SSD for storage. You can install either
one for storage.
To install the mSATA (half size) drive:
1. Make sure the NVR is power-off.
2. Unscrew the four screws on the rear panel and then remove the cover from the housing.
3. Find the mSATA Interface on the motherboard and then screw your mSATA (half size) drive
to the mSATA Interface using the supplied mSATA Screw.
mSATA Interface
Chapter
2

eIVP1300 AI Mobile NVR
6
To install a 2.5” SSD:
1. Make sure the NVR is power-off.
2. Unscrew the four screws on the rear panel and then remove the cover from the housing.
3. Screw the SSD to the lower housing cover using the supplied SSD Screws. Find the SATA cable
inside the NVR, and connect the SATA cable to the SATA port on the SSD.
4. Screw the housing cover back to the NVR.
2.1.1 Storage Compatibility List
Please go to the product page (Download) on EverFocus’ Website www.everfocus.com.tw to see
the latest Storage Compatibility List. It’s recommended to use the storage models listed on the
Storage Compatibility List to ensure your storage devices are compatible.

eIVP1300 AI Mobile NVR
7
2.2 DC Out Cable
The eIVP1300 provides a total of 12V/2A DC output with four sets of power output wires (+/-)
for the connected IP cameras.
Connect the supplied DC Out Cable to the DC Out port on the rear panel of the NVR.
+ (black with white stripe)
- (black)

eIVP1300 AI Mobile NVR
8
3. AMI BIOS Setup
3.1 System Test and Initialization
The board uses certain routines to perform testing and initialization. If an error, fatal or non-fatal,
is encountered, a few short beeps or an error message will be outputted. The board can usually
continue the boot up sequence with non-fatal errors.
The system configuration verification routines check the current system configuration against the
values stored in the CMOS memory. If they do not match, an error message will be outputted, in
which case you will need to run the BIOS setup program to set the configuration information in
memory.
There are three situations in which you will need to change the CMOS settings:
•You are starting your system for the first time
•You have changed your system’s hardware
•The CMOS memory has lost power and the configuration information is erased
The system’s CMOS memory uses a backup battery for data retention, which is to be replaced
once emptied.
Chapter
3

eIVP1300 AI Mobile NVR
9
3.2 AMI BIOS Setup
The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic system
configurations, which is stored in the batter y-backed CMOS RAM and BIOS NVRAM so that the
information is retained when the power is turned off.
To enter BIOS Setup, press <Del> or <F2> immediately while your computer is powering up.
The function for each interface can be found below.
•Main – Date and time can be set here. Press <Tab> to switch between date elements
•Advanced – Enable/ Disable boot option for legacy network devices
•Chipset – For hosting bridge parameters
•Boot – Enable/ Disable quiet Boot Option
•Security – The setup administrator password can be set here
•Save & Exit –Save your changes and exit the program
3.3 Setup Submenu: Main
Press the “Delete” key to enter the setup page.

eIVP1300 AI Mobile NVR
10
3.4 Setup Submenu: Advanced
3.4.1 Advanced: Power Management

eIVP1300 AI Mobile NVR
11
Options summary:
Power Mode ATX Type Optimal Default, Failsafe Default
AT Type
Select power supply mode
Restore AC Power
Loss
Power Off
Optimal Default, Failsafe Default
Power On
Last State
Select AC power state when power is re-applied after a power failure
Enable ACPI Auto
Configuration
Enable
Optimal Default, Failsafe Default
Disable
Enables or Disables BIOS ACPI Auto Configuration
Enable Hibernation Enable Optimal Default, Failsafe Default
Disable
Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be
not effective with some OS
ACPI Sleep State Suspend Disabled
Optimal Default, Failsafe Default
S3 only(Suspend to RAM)
Select highest ACPI sleep state the System will enter when the Suspend button is
pressed
Lock Legacy
Resources
Enable
Optimal Default, Failsafe Default
Disable
Enables or Disables Lock of Legacy Resources
Wake on Ring Enable Optimal Default, Failsafe Default
Disable
Enabled/Disabled wake from Ring
Wake on LAN Enable Optimal Default, Failsafe Default
Disable
Enabled/Disabled wake from LAN
S5 RTC Wake
Settings
Enable system to wake from S5 using RTC alarm.

eIVP1300 AI Mobile NVR
12
3.4.1.1 Power Management: S5 RTC Wake Settings
Options summary:
Wake system with Fixed Time Enable
Optimal Default, Failsafe Default
Disable
Enable or disable System wake on alarm event. Wake up time is setting by following
settings.
Wake up day 0 - 31
Select 0 for daily system wake up 1 - 3 1 for which day of the month that you would like
the system to wake up
Wake up hour 0-23
Wake up minute 0-59
Wake up second 0-59
Wake system with Dynamic Time Enable
Optimal Default, Failsafe Default
Disable
Enable or disable System wake on alarm event. Wake up time is current time + Increase
minutes.
Wake up minute increase 1 - 15

eIVP1300 AI Mobile NVR
13
3.4.2 Advanced: Super IO Configuration
3.4.2.1 Super IO Configuration: Serial Port 1 Configuration

eIVP1300 AI Mobile NVR
14
3.4.2.2 Super IO Configuration: Serial Port 2 Configuration
3.4.2.3 Super IO Configuration: Serial Port 3 Configuration