EverFocus M105-DE100-002 User manual

OPERATION MANUAL
HIGH RESOLUTION
DOME CAMERA
M105-DE100-002
Thank you for choosing our high quality camera.
Before attempting to connect operate this unit, please read and follow these instructions.

CONTENTS
1. Cautions
2. Features
3. Package
4. Overview and function
5. Installation
6. Connection
7. Dimensions
8. Specifications
9. OSD Menu Structure
3

1. CAUTIONS
4
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio / tv technician for help.
Caution
Any changes or modications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a protective earthing
connection.

1. CAUTIONS
5
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2.Features
• 1/3 960H SONY EXview HAD CCD II
• High Resolution of 700TV Lines
• OSD Function
• Multi Language
(ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN / PORTUGUESE / SPANISH / CHINESE)
• 2DNR
• Privacy Zone
• Motion Detect
• DC12V / AC24V Dual Voltage
• ATR(Adaptive Tone-curve Reproduction / Digital WDR)
The function provides gradation compensation to improve the contrast of subjects both
low-luminance areas and high luminance areas exist in the same picture
• 3-Axis Gimbal
• Service Video connector
The Service Video Connector also provides the installer with an easy way of conguring the
camera.
6

3.Package
1 DOME CAMERA
2VIDEO OUTPUT TEST CABLE
3OPERATION MANUAL
4 SCREW - 3ea
5 MOUNT GUIDE
7

4.Overview and function
8
• Name (Standard)
• CONTROL FUNCTION
(OSD JOYSTICK)
LEFT
UP
RIGHT
DOWN
MENU
• Name (LED Type)

5. Installation
9
NO PART NAME
STANDARD Type LED Type
1Mount Guide
2Housing Botton
3Holder Panning
4Holder Tlit
5Holder Rotate
6Cover Sun Shield Cover LED
7Housing Top
8Cover, Dome
Standard Type
LED Type

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
6.Connection
• DUAL(DC 12V/AC24V)
• DC 12V
10
BNC FEMALE
VIDEO
VIDEO IN
DC 12V POWER SUPPLY
BNC FEMALE
VIDEO
VIDEO IN
DC 12V / AC 24V
DUAL POWER SUPPLY

7.Dimensions
Unit : mm
11
Ø136.4
45
95.3
Ø100

8.Specifications
Signal Format NTSC PAL
Image Device 1/3˝ 960H SONY EXview HAD CCD II
Scanning System 2:1 Interlace
H.Resolution 700TV Lines
Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz
Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)
Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Electronic Shutter Speed 1/60 sec 1/50 sec
S/N Ratio More than 50dB(AGC Off)
Gamma r=0.45
Min. Illumination COLOR : 0.05Lux/F1.2, BW : 0.02 Lux/F1.2
Sync System Internal
Video Output 1.0 Vp-p Composite(75Ω)
OSD Built in (Inner Key / Joystick)
BLC OFF / BLC / HLC
White Balance ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK
2DNR OFF / ON (Level adjustable)
ATR OFF / ON (Level adjustable)
Function MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN
Privacy Masking 4 Zones
Motion Detection 4 Zones
Day & Night AUTO
Language ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN/
PORTUGUESE / SPANISH / CHINESE
Power
Consumption
DC12V DC 12V (±10%) Max.120mA
Dual DC 12V (±10%) Max.150mA , AC 24V (±10%) Max. 2.3W
Operating Temperature -10℃~ +50℃
Storage Temperature -20℃~ +60℃
Operating Humidity Less than 80%
Options Dual Power
Weight Approx. 343g
Dimension(mm) 136.4(Φ) x 95.3(mm)
LED TYPE
Power
Consumption
DC12V DC 12V (±10%) Max. 320mA
Dual DC 12V (±10%) Max 390mA , AC 24V (±10%) Max. 4.8W
Min. Illumination 0 Lux (IR LED ON)
IR LED 850nm, 30ea
IR Beam Range Up to 30M
IR LED Operation On : 1 Lux, Off : 3 Lux
Specifications and designs are subject to change for improving the functionality of this product without notice.
12

9. OSD MENU STRUCTURE
MAIN
MENU
1st Sub
MENU
2nd Sub
MENU
3rd Sub
MENU
4th Sub
MENU
LENS
MANUAL
AUTO
TYPE DC
MODE AUTO,OPEN,CLOSE
SPEED (000 ~ 255)
RETURN
SHUTTER
/ AGC
AUTO
HIGH LUMINANCE MODE SHUT,AUTO IRIS, SHUT+AUTO IRIS
BRIGHTNESS (000 ~ 255)
LOW LUMINANCE MODE AGC,OFF
BRIGHTNESS x0.25,x0.50,x0.75,x1.00
RETURN
MANUAL
MODE SHUT+AGC
SHUTTER
1/50(PAL),1/100(NTSC)
1/60(NTSC),1/120(PAL)
1/250,1/500,1/1000
1/2000,1/4000,1/10000
AGC 6,12,18,24,30,36,42,44.8
RETURN
WHITE
BAL
ATW
SPEED (000 ~ 255)
DELAY CNT (000 ~ 255)
ATW FRAME x0.50,x1.00,x1.50,x2.00
ENVIRONMENT INDOOR,OUTDOOR
RETURN
PUSH
USER1
B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN
USER2
B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN
ANTI CR
MANUAL LEVEL 24 ~ 103
RETURN
PUSH LOCK
BACK LIGHT OFF,BLC,HLC
PIC
ADJUST
MIRROR OFF,ON
BRIGHTNESS (000 ~ 255)
CONTRAST (000 ~ 255)
SHARPNESS (000 ~ 255)
HUE (000 ~ 255)
GAIN (000 ~ 255)
RETURN
ATR ON
LUMINANCE LOW,MID,HIGH
CONTRAST LOW,MIDLOW,MID,MIDHIGH,HIGH
RETURN
OFF
*SHUT+IRIS:Both the Shutter and the Mechanical Iris are automatically adjusted according to brightness.
*Auto Iris(Default): The Shutter stays at the manually selected value and only the Mechanical Iris adjusts to brightness.
13

9. OSD MENU STRUCTURE
MAIN
MENU
1st Sub
MENU
2nd Sub
MENU
3rd Sub
MENU
4th Sub
MENU
MOTION
DET
ON
DETECT SENSE (000 ~ 255)
BLOCK DISP OFF,ON,ENABLE (CONTROLER)
MONITOR AREA ON,OFF
AREA SEL
1/4, 2/4, 3/4, 4/4
TOP NTSC:(000 ~ 244) / PAL: (000 ~ 288)
BOTTOM NTSC:(000 ~ 244) / PAL: (000 ~ 288)
LEFT NTSC:(000 ~ 474) / PAL: (000 ~ 468)
RIGHT NTSC:(000 ~ 474) / PAL: (000 ~ 468)
RETURN
OFF
NEXT
EXIT
SAVE ALL
PRIVACY ON
AREA SEL
1/4, 2/4, 3/4, 4/4
TOP NTSC:(000 ~ 244) / PAL: (000 ~ 288)
BOTTOM NTSC:(000 ~ 244) / PAL: (000 ~ 288)
LEFT NTSC:(000 ~ 474) / PAL: (000 ~ 468)
RIGHT NTSC:(000 ~ 474) / PAL: (000 ~ 468)
COLOR (1 ~ 8)
TRANSP 0.00, 0.50, 0.75, 1.00
MOSAIC OFF,ON
RETURN
OFF
NR
NR MODE OFF,Y,C,Y/C
C LEVEL (000 ~ 015)
Y LEVEL (000 ~ 015)
RETURN
CAMERA
ID
ON EDIT MODE
RETURN
OFF
LANGUAGE ENGLISH, 日本語, DEUTSCH, FRANCAIS, Русский, PORTUGUÊS, ESPAÑOL, 中文
CAMERA
RESET
BACK
EXIT
SAVE ALL
*Important Note :
- Any changes made to the camera settings must be saved prior to exiting the OSD menu.
Else all changes will be discarded.
- By changing the lens option in the OSD from MANUAL to AUTO will automatically change the
SHUTTER/AGC setting from AUTO IRIS to SHUT+AUTO IRIS.(Default:AUTO IRIS)
14