EverHot EVH 90+ User manual

With Everhot Cookers’ policy of continuous product improvement, the manufacturer reserves the right to change specifications and make
modifications to the appliance described and illustrated at any time
s:/installation specs/EVH 90+ installation spec.doc/ver2022_2
INSTALLATION INSTRUCTIONS & SPECIFICATION
PRE –INSTALLATION
NOTE: The preparation of the site, in readiness for the installation of the appliance, is the
responsibility of the site owner, not of the manufacturer of the appliance.
a. The floor must be level and capable of supporting the weight of the cooker (approximate weight 300kg).
b. It is important to ensure the flooring is laid before delivery and runs underneath the cooker. Flooring
should not be laid up to the cooker after installation.
c. The cooker measurements are 600mm deep and 900mm high to the working surface with a width of
890mm.
d. The cooker is 900mm high to the working surface. If the cooker needs to be raised to match worktop
levels, this should be done by way of a plinth built to the appropriate height prior to delivery.
e. The EVH 90+ should be installed with a minimum of 30mm clearance from the back wall. This 30mm
gap is best sealed with a worktop upstand, though a standard 30mm stainless infill strip that fits to the
back of the cooker is supplied with the Everhot. On no account should any Everhot model be pushed
hard against the back wall as this may damage the electric cable. A minimum gap of 5mm per side is
required to allow installation and removal of the cooker –please contact us in advance of installation if
this is not possible. Where the end grain of a wooden worktop is adjacent to the cooker, we recommend
that this is increased to 10mm to minimise the chance of the worktop splitting.
f. Clearance must be allowed for the raising of the cooker lid into the upright position (minimum height of
1530mm from ground level). Please see side view diagrams for further clarification. A 5mm gap on each
side of the cooker lid should be allowed when in the raised position (the lids are slightly inset from the
side of the cooker to allow for overhead cupboards).
g. The appliance must be used on 220-240V AC only and should be plugged into a standard 13 amp socket.
The 13 amp socket should be accessible and positioned adjacent to the cooker, so as not to impede the
opening of the top lid, and ensuring the plug is not exposed to steam or excessive moisture. If the socket
cannot be positioned immediately adjacent to the cooker, please see diagrams attached for exact lengths
of cables (unfortunately it is not possible to extend these cable lengths). If the power supply cord is
damaged, it must be replaced by the manufacturer or their representative, as special purpose tools are
required. An Everhot cooker should NOT be hard wired –please install using the supplied 13amp plug.
Your EVERHOT cooker has been built to comply with the following UK and European Directives, and carries the UKCA and CE mark.
1.EMC Directive (2014/30/EU) 2. Low Voltage Directive (2014/35/EU)
3. Electromagnetic Compatibility Regulations (2016) 4. Electrical Equipment (Safety) Regulations (2016)
Control of Substances - Health and Safety
This appliance contains the following substances indicated below. It is the User’s/Installer’s responsibility to ensure that the appropriate precautions
are taken when handling, where applicable, any of the materials that could be interpreted as being injurious to health and safety.
Mineral wool, Glass Yarn.
May cause irritation to the skin, eyes, nose and throat, may be harmful if inhaled. Use appropriate protective clothing to avoid contact with body. After
handling, wash hands and other exposed parts.
Your cooker does not contain ceramic insulants.
The EVERHOT is a high quality appliance that will provide decades of use, however when you feel that it has reached the end of its working life, please
contact us and we will remove it and recycle it free of charge

With Everhot Cookers’ policy of continuous product improvement, the manufacturer reserves the right to change specifications and make
modifications to the appliance described and illustrated at any time
s:/installation specs/EVH 90+ installation spec.doc/ver2022_2
INSTALLATION INSTRUCTIONS & SPECIFICATION
The diagrams below are not to scale and are simply to show the relevant dimensions –
sockets can be placed either side of the cooker.
(Note: EVH 90+ right-hand oven is mirror image)
POST INSTALLATION
Point a. below will normally be checked by the EVERHOT technician who installs your cooker
a. Before use, check that the cooker is level, upright and stable.
b. On reaching working temperature, ensure that the hot/simmer plate surfaces are flush with
the surrounds - this can be adjusted using a 5mm allen key in the bolts at each corner of
the hotplates.
c. On initial heating up odours may be given off from the insulants used. These will disappear
after a number of hours.
Where holes are prepared in
advance for plugs (any model) or
controlbox conduit (60 / 120+
only) to pass through, these should
be at least 60mm in diameter