EVERLUX Excellence User manual

Technical Characteristics
Excellence Installation Guide
Mod.277_EXC_EN Edição: 08-03-18 Página 1 de 4
Scope/ About this Guide
This installation guide for Everlux Signage Systems aims to provide the practical guidelines for a proper
installation of Excellence signage.
I –Before Installation
General considerations
In order to maximize the quality of the installation as well as its efficiency and effectiveness it is essential that
before the installation the installer do a rigorous analysis of the type of surface where the signage should be
installed. The installation method shall be selected considering the application surface.
Note: A rough and porous wall will not allow the application of self-adhesive elements and may require fixing by
using screws. However smooth surfaces provide good fixing conditions for gluing.
Selecting an installation method
Different types of signage can be selected depending on the desired viewing angle. There are 3 possible
installation types available for the Excellence signage:
Wall mounted
Perpendicular to the wall
Suspended from the ceiling
Single sided installation
Directly installed on to the surface
Single or double sided sign.
.
Single or double sided sign.

Technical Characteristics
Excellence Installation Guide
Mod.277_EXC_EN Edição: 08-03-18 Página 2 de 4
Necessary tools
•Drill;
•Meter;
•Pencils for marking
•Ruler;
•Level;
To achieve an efficient adhesion, it is essential to ensure the elimination of dust and grease through a good
cleaning on the application surface. After surface cleaning, the bonding shall be carried out by applying double-
sided adhesives.
2. Installation
The installation method depends on the type of sign being fitted. Shown below are the four types of fixing:
2.1 Wall mounted installation
The wall mounted fixing can be carried out by drilling or adhesive fixing.
Fixing
Operation description
Assembly sequence
Adhesive
▪Mark the location of the signs on the
installation surface
▪Remove the protection from the
adhesives applied to the accessories
▪Apply the sign on the installation
surface previously marked
Note: Before installation, it must be
checked whether the usage of adhesive as
installation solution is suitable for the
surface type.
Drilling
▪Mark the location of signs on the
installation surface using the drilling
guide
▪Do the necessary drilling on the
surface previously marked
▪Remove the protective film from the
back of signs before the installation
▪Apply the signs on the surface
according to the installation sequence
indicated a) b) c) d) e)
a) Remove protection from the
adhesives
b) Application of accessory 1
c) Application of accessory 2
1
2
3
1
2
a) Application of accessory 1
b) Application of accessory 3
c) Application of screw 4
d) Application of sign
e) Application of accessory 2
4

Technical Characteristics
Excellence Installation Guide
Mod.277_EXC_EN Edição: 08-03-18 Página 3 de 4
2.2 Installation perpendicular to the wall
Fixing
Operation description
Assembly sequence
Drilling
▪Mark the location of signs on the
installation surface using the drilling
guide
▪Do the necessary drilling on the
surface previously marked
▪Remove the protective film from the
back of signs before the installation
▪Apply the signs on the surface
according to the installation sequence
indicated a) b) c) d) e)
1
2
3
4
v
5
a) Application of accessory 1
b) Application of accessory 5
c) Application of screw 6
d) Application of accessory 4
e) Application of accessories 2 and 3
6

Technical Characteristics
Excellence Installation Guide
Mod.277_EXC_EN Edição: 08-03-18 Página 4 de 4
2.3 Installation suspended from the ceiling
Fixing
Operation description
Assembly sequence
Drilling
1. Mark the location of the signs on the
ceiling
2. Do the necessary drilling on the
surface previously marked
3. Remove the protective film from the
back of sign before installation
4. Apply the signs on the installation
surface according to the installation
sequence indicated a) b) c) d) e) f) g) h) i)
.
.
1
2
3
4
v
5
6
7
8
a) Application of accessory 1
b) Application of accessory 6
c) Application of accessory 7
d) Application of accessories 2 and 3 on the lower holes
e) Application of accessories 4 and 3 on the upper holes
f) Application of accessory 6 on the other end of the steel
cable
g) Application of accessory 5 on the steel cable
h) Checking the desired height of the tight accessory 7, by
using the accessory 8
i) Cut the excess of the steel cable next to the accessory 7