Everpower Electronics 3PA5015R User manual

CAUTION
1. SAVE THIS INSTRUCTIONS-This manual contains important safety and
operating instructions for the 3PA5015R battery charger.
Please read the caution of batteries or devices you want to charge firstly!
2. When charging, batteries can emit explosive gases, therefore it is essential to
prevent flames and sparks. The charger is designed for charging lead-acid
batteries from 2 to90Ah. Do not use for any other purpose.
3. Always provide good ventilation when charging.
4. Use of an attachment not recommended or sold by Everpower may result in a risk
of fire, electric shock or serious injury to persons.
5. To reduce risk of damage to electric plug and cord, pull by the plug rather than by
the cord when disconnecting charger.
6. An extension cord should not be used unless absolutely necessary. Use of an
improper extension cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure that: a) Pins on plug of extension cord
are the same number, size and shape as those of plug on charger; b) Extension
cord is properly wired and in good electrical condition; and c) Wire size is large
enough for ac ampere rating as specified in “technical data”.
7. Do not operate charger with a damaged cord or plug-return the charger to the
place where purchased.
8. Never operate the charger if it has received a sharp blow, been dropped or
otherwise damaged in any way; take is to a qualified serviceman.
9. Do not disassemble the charger; take it to a qualified serviceman when service
or repair is required. Incorrect reassemble may result in a risk of electrical shock
or fire.
10. To reduce risk of electric shock, unplug charger from AC outlet before attempting
any maintenance or cleaning. Turning off controls will not reduce the risk.
3PA5015R 12V Lead-Acid Battery Charger
User’s Manual
Everpower Electronics Co.,Ltd

Brief Introduction
3PA5015R represents today’s new technology for lead-acid type battery charging.
3PA5015R programmed four auto stages ( Ud-I-Uo-Up) charging process, It is
designed for all kinds of 12V 2-90Ah lead-acid battery, such as SLA, AGM and Gel
battery. Stage “Ud” desulfurating the battery through 20V pulse, when the battery
recovered, stage ‘I’ will give bulk current charging( 0.8A or 3.3A, defined by user, for
2-8Ah 0.8A is prefer, 12-90Ah should select 3.3A). Then “Uo” stage is followed, the
output voltage is fixed on 14.4V (14.7V is for low temperature, <5℃); When the
current declined to 0.4A; stage “Up” will turn on duty. At this stage, the battery is
charged completely and the charger gives some pulse to maintenance the battery.
Specification
Input Voltage 100-249VAC, 50-60Hz
Input Current 1.1A
Back current drain 1) 1.3mA
Charge voltage Rating 12V, Bulk 14.4V/14.7V (14.7V for low temperature)
Ripple 2) Voltage-ripple 50mV rms, Current-ripple 0.13A
Charge current 0.8A(2-8Ah, for motocycle) 3 3A (8-90Ah,for Car batt)
OperateTemperature -20℃-50℃
Cooling Natural convection. Do not cover the charger.
Charge principle Auto 4 stages: Ud-I-Uo-Up
Battery type All types of 12V lead-acid batteries. (SLA,GEL,AGM…..)
Battery capacity 2-90Ah
Size 120*67*41 (L*W*H)
Enclosure Waterproof splash/ rain-proof
Weight 275g
zThe back current drain (reverse current) is the current that the charger uses form
the battery when the wall plug is not connected.
zThe ripple wave describes how many disturbances are exhibited by current and
voltage. A rippled voltage can cause damage to other equipment connected to
the battery.
Display Panel
How to use:
1. Connect positive charger clip (red) to positive battery terminal, the black clip to
negative. (You can use other appendix wires to connectbattery).
2. Connect the AC cord to the socket, the red alarm indication light will indicate a
battery which is connected to reverse polarity.
3. Pressing the “MODE-button” and stepping forward one press at a time until the
required mode is reached, the button is then release.
4. When the “charging finished” led lights up, the battery is fully charged. When
disconnecting charger, disconnect in reverse sequence from connecting
procedure.
The table show the duration of the Bulk step up to about 80% state of charger.
Battery Type (Ah) MODE Timer (hours)
2 2-3
8 8-10
14 3-4
50 12-14
90 23-26
Mode
select
button
Errors!
（Such as
reversed…）
Desul
f
u-
rating
process
C
haring
process
Chargingfinished.
Pulse maintenance
Power
on 2-12Ah
battery
setting
12-90Ah
battery
settin
g
Low
temperature
setting