evertz exponent 500ADA User manual

Frame Manual
500ADA Analog Video Distribution Amplifier
TABLE OF CONTENTS
1. OVERVIEW......................................................................................................................................... 1
2. INSTALLATION.................................................................................................................................. 2
3. SPECIFICATIONS.............................................................................................................................. 3
3.1. ANALOG VIDEO INPUT............................................................................................................ 3
3.2. ANALOG VIDEO OUTPUTS ..................................................................................................... 3
3.3. ELECTRICAL ............................................................................................................................ 3
3.4. PHYSICAL................................................................................................................................. 3
4. STATUS LEDS ................................................................................................................................... 4
5. CIRCUIT DESCRIPTION.................................................................................................................... 4
6. JUMPERS AND USER ADJUSTMENTS ........................................................................................... 4
6.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS......................................................................................... 5
6.2. SELECTING THE INPUT TERMINATION................................................................................. 5
6.3. SELECTING THE INPUT AC/DC COUPLING .......................................................................... 5
6.4. GAIN ADJUSTMENT................................................................................................................. 5
Figures
Figure 1: 500ADA Block Diagram ....................................................................................................................... 1
Figure 2: 500ADA Rear Panel Overlay ............................................................................................................... 2
Figure 3: LED and Jumper Locations.................................................................................................................. 4
Revision 1.1

Frame Manual
500ADA Analog Video Distribution Amplifier
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 Original Version Oct 02
1.1 Spec Updated to Rev A PCB Nov 02
Revision 1.1

Frame Manual
500ADA Analog Video Distribution Amplifier
1. OVERVIEW
The 500ADA Analog Distribution Amplifier is a general purpose amplifier for distributing analog video
signals. The 500ADA features one balanced input with nine outputs. The 500ADA amplifier has been
designed to distribute a wide range of analog video signals. It can also distribute other pulses and signals
that are less than 2Vp-p.
The 500ADA is housed in the 500FR Frame that will hold up to 16 modules.
Features:
• 75 Ohm or high impedance input (jumper selectable)
• High common mode range and common mode rejection ratio (CMMR)
• Gain control
• Jumper selectable AC or DC coupling
• Looping feature with external "T" connector
• Consistent input impedance if card power is lost
9 Analog
Outputs
Impedance
AC/DC
Coupling
75 Ω
Balanced
Analog Input
Gain
FAULT
Controls/
Indicators
Figure 1: 500ADA Block Diagram
Revision 1.1 500ADA-1

Frame Manual
500ADA Analog Video Distribution Amplifier
2. INSTALLATION
The 500ADA comes with a companion rear panel overlay that can be placed over the rear panel BNC
connectors to identify their function. For information on inserting the module into the frame see the 500FR
chapter section 3.
Figure 2: 500ADA Rear Panel Overlay
IN Input (isolated) BNC connector for analog video signals. The TERM jumper located on the
module near the back determines whether the input signal will be high impedance or
terminated with 75 ohms. (See section 6.2) The INPUT jumper located on the module near
the back determines whether the input signal will be AC or DC coupled. (See section 6.3)
OUT 1 to 9 There are nine BNC connectors with level adjusted copies of the input signal.
500ADA-2 Revision 1.1

Frame Manual
500ADA Analog Video Distribution Amplifier
3. SPECIFICATIONS
Note: At the time of printing, this product has only been qualified for use with standard definition signals. It,
however, has been designed to work with high definition signals. Frequency and phase response will not
be optimized at the upper frequency range of high definition video bandwidths.
All specifications, unless indicated, measured under the following conditions:
• 1 Vp-p video applied
• 75 Ohm card input terminated
• AC coupled
• Gain adjusted for unity operation into 75 Ohm load
3.1. ANALOG VIDEO INPUT
Standards: Any analog video format, up to 2Vp-p and 30MHz bandwidth
Connector: 1 BNC input per IEC 169-8
Common mode range: >6Vp-p
CMRR: > 70dB to 1kHz
Signal amplitude: 2.5Vp-p max
Impedance: 75Ohms terminated, 35kOhms Hi-Z (jumper selectable)
Coupling: AC or DC (jumper selectable)
Return loss: >40dB to 10MHz, >30dB to 30MHz
3.2. ANALOG VIDEO OUTPUTS
Number of Outputs: 9 Per Card
Connector: BNC per IEC 169-8
Output impedance: 75 Ohm
Gain control range: ± 5dB
DC level (DC Coupling active) < +/- 100mV
Freq. Response: <+/-0.05dB (to 5.5MHz)
Differential Gain: <0.17 %
Differential Phase: < 0.19 deg
C/L gain inequality: <+/-0.1%
C/L Delay: <+/-2nsec
Output isolation: 42dB to 10MHz, 32 dB to 30MHz
Output return loss: >40dB to 30MHz
Noise performance: <-78dB RMS NTC7 weighting,
<-70dB RMS 15kHz to 5.5MHz
3.3. ELECTRICAL
Voltage: + 12VDC
Power: 1.2 Watts
3.4. PHYSICAL
Number of slots: 1
Revision 1.1 500ADA-3

Frame Manual
500ADA Analog Video Distribution Amplifier
4. STATUS LEDS
The 500ADA has two LED Status indicators on the front card edge to show operational status of the card
at a glance. Figure 3 shows the location of the LEDs.
Two large LEDs on the front of the board indicate the general health of the module
LOCAL FAULT: This Red LED indicates poor module health and will be On if a local input power
fault exists (i.e.: a blown fuse). The LOCAL FAULT indication can also be reported
to the frame through the FRAME STATUS jumper.
MODULE OK: This Green LED indicates good module health. It will be On when the board power
is good.
5. Circuit Description
The input signal enters the board through a BNC with isolated ground so that balanced input processing
may be done to remove any common mode hum that may have been added to the signal and ground
shield. On-board jumpers allow you to configure the input impedance and input coupling (AC/DC).
An adjustable gain stage feeds three separate OP-Amps drive the nine output BNC's with 75-Ohm output
impedance.
6. JUMPERS AND USER ADJUSTMENTS
J1
FRAME STATUS
ON
OFF
+12V GND
GAIN
MODULE STATUS
(2)500ADA
J5
75R
HI-Z
TERM
J4
DC
AC
INPUT
Figure 3: LED and Jumper Locations
500ADA-4 Revision 1.1

Frame Manual
500ADA Analog Video Distribution Amplifier
6.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS
The FRAME STATUS jumper J1, located at the front of the module determines whether local faults (as
shown by the Local Fault indicator) will be connected to the 500FR frame's global status bus.
FRAME STATUS: To monitor faults on this module with the frame status indicators (on the power
supply’s FRAME STATUS LED's and on the Frame's Fault Tally output) install this
jumper in the On position.
When this jumper is installed in the Off position local faults on this module will not
be monitored.
6.2. SELECTING THE INPUT TERMINATION
The input termination may be set via card jumper J5 to either 75 Ohms (default) or Hi-Z (34k Ohms). Set it
to Hi-Z when using a "T" connector to loop the signal through several device inputs.
6.3. SELECTING THE INPUT AC/DC COUPLING
The input may be AC or DC (default) coupled into the input-circuitry using jumper J4. Use AC coupling in
applications when the input signal has a large (>2V) DC level. In some non-video applications that do not
have DC information (i.e. digital AES audio), AC coupling can be used to remove any DC level that may
have built up in its transmission.
6.4. GAIN ADJUSTMENT
The GAIN POT on the cards front edge allows you to adjust the input signal level. Turning the POT
clockwise will increase the gain.
!
There is enough range on this control to counteract the video level error due to a
missing or double terminated coaxial connection. This will hide a frequency
response problem due to the mis-termination.
Revision 1.1 500ADA-5

Frame Manual
500ADA Analog Video Distribution Amplifier
This page left intentionally blank
500ADA-6 Revision 1.1