Evolution FURY62102 User manual

Date Published: 01 / 03 / 2016Written in UK English
EN
DE
FR
TR
Original Instructions
FURY6

EN

EN
DE
FR
TR
EN
ENGLISH
Original Instructions

4
www.evolutionpowertools.com
TABLE OF CONTENTS
English Page 2
Deutsch Seite 34
Français Page 68
Türk Sayfa 100
INTRODUCTION Page 5
Guarantee Page 5
Machine Specification Page 6
Vibration Page 7
Labels and Symbols Page 7
Intended use of this Power Tool Page 8
Prohibited use of this Power Tool Page 8
SAFETY PRECAUTIONS Page 9
Electrical Safety Page 9
Outdoor Use Page 9
General Power Tool Safety Instructions Page 11
Additional Safety Instructions Page 13
GETTING STARTED Page 14
Unpacking Page 14
Machine Overview Page 15
Service Parts Diagram Page 16
Assembly and Preparation Page 17
Operating Instructions Page 18
MAINTENANCE Page 29
Environmental Protection Page 29
DECLARATION OF CONFORMITY Page 31

5
www.evolutionpowertools.com
EN
DE
FR
TR
(1.2) THIS INSTRUCTION MANUAL
WAS ORIGINALLY WRITTEN IN ENGLISH
(1.3) IMPORTANT
Please read these operating and safety
instructions carefully and completely.
For your own safety, if you are uncertain
about any aspect of using this equipment
please access the relevant Technical Helpline,
the number of which can be found on the
Evolution Power Tools website. We operate
several Helplines throughout our worldwide
organization, but Technical help is also
available from your supplier.
WEB
www.evolutionpowertools.com
(1.4) Congratulations on your purchase
of an Evolution Power Tools Machine.
Please complete your product registration
‘online’as explained in the A4 online
guarantee registration leaflet included with
this machine. You can also scan the QR code
found on the A4 leaflet with a Smart Phone.
This will enable you to validate your machine’s
guarantee period via Evolutions website by
entering your details and thus ensure prompt
service if ever needed. We sincerely thank
you for selecting a product from
Evolution Power Tools.
EVOLUTION LIMITED GUARANTEE.
Evolution Power Tools reserves the right
to make improvements and modifications
to the product design without prior notice.
Please refer to the guarantee registration
leaflet and/or the packaging for details of
the terms and conditions of the guarantee.
(1.5) Evolution Power Tools will, within
the guarantee period, and from the original
date of purchase, repair or replace any
goods found to be defective in materials or
workmanship. This guarantee is void if the tool
being returned has been used beyond the
recommendations in the Instruction Manual or
if the machine has been damaged by accident,
neglect, or improper service.
This guarantee does not apply to machines
and / or components which have been altered,
changed, or modified in any way, or subjected
to use beyond recommended capacities
and specifications. Electrical components
are subject to respective manufacturers’
warranties. All goods returned defective
shall be returned prepaid freight to
Evolution Power Tools.
Evolution Power Tools reserves the right to
optionally repair or replace it with the same
or equivalent item. There is no warranty –
written or verbal – for consumable accessories
such as (following list not exhaustive) blades,
cutters, drills, chisels or paddles etc. In no
event shall Evolution Power Tools be liable for
loss or damage resulting directly or indirectly
from the use of our merchandise or from any
other cause. Evolution Power Tools is not
liable for any costs incurred on such goods or
consequential damages. No officer, employee
or agent of Evolution Power Tools is authorized
to make oral representations of fitness or
to waive any of the foregoing terms of sale
and none shall be binding on Evolution
Power Tools.
Questions relating to this limited guarantee
should be directed to the company’s head
office, or call the appropriate Helpline number.

6
www.evolutionpowertools.com
SPECIFICATIONS
MACHINE METRIC IMPERIAL
Motor (230-240V~ 50 Hz) 1200W 5A
Speed No Load 3500min-1 3500rpm
Weight 9.45kg 20lb
CUTTING CAPACITIES METRIC IMPERIAL
Mild Steel Plate - Max Thickness 3mm 1/8”
MAXIMUM CUTTING CAPACITY ALUMINIUM, WOOD & PVC
MITRE SAW CONFIGURATION
MITRE BEVEL MAX WIDTH
OF CUT MAX DEPTH OF CUT
90°90°115mm (4-1/2”) 55mm (2-1/8”)
45°90°65mm (2-1/2”) 55mm (2-1/8”)
45°45°40mm (1-9/16”) 25mm (15/16”)
MAXIMUM CUTTING CAPACITY TABLE SAW CONFIGURATION
CUTTING CAPACITIES METRIC IMPERIAL
Wood - Max Thickness 32mm 1-1/4”
BLADE DIMENSIONS METRIC IMPERIAL
Diameter 210mm 8-1/4”
Bore 25.4mm 1”
Number of Teeth 20 20
Kerf 1.7mm 1/16”
NOISE & VIBRATION DATA
Sound Pressure LPA 94.57dB(A) K=3dB(A)
Sound Power Level LWA 107.57dB(A) K=3dB(A)
Vibration Level 2.5m/s2K=1.5m/s2
(1.6) Note: The vibration measurement was made under standard conditions in accordance with:
BS EN 61029-1:2009+A11.

7
www.evolutionpowertools.com
EN
DE
FR
TR
The declared vibration total value has been
measured in accordance with a standard test
method and may be used for comparing one
tool with another.
The declared vibration total value may also be
used in a preliminary assessment of exposure.
(1.7) VIBRATION
WARNING: When using this machine the
operator can be exposed to high levels of
vibration transmitted to the hand and arm. It
is possible that the operator could develop
“Vibration white finger disease”(Raynaud
syndrome). This condition can reduce the
sensitivity of the hand to temperature as well
as producing general numbness. Prolonged
or regular users of this machine should
monitor the condition of their hands and
fingers closely. If any of the symptoms become
evident, seek immediate medical advice.
• The measurement and assessment of
human exposure to hand-transmitted
vibration in the workplace is given in:
BS EN ISO 5349-1:2001 and
BS EN ISO 5349-2:2002.
• Many factors can influence the actual
vibration level during operation e.g. the
work surfaces condition and orientation
and the type and condition of the machine
being used. Before each use, such factors
should be assessed, and where possible
appropriate working practices adopted.
Managing these factors can help reduce the
effects of vibration:
Handling
• Handle the machine with care,
allowing the machine to do the work.
• Avoid using excessive physical effort
on any of the machines controls.
• Consider your security and stability,
and the orientation of the machine
during use.
Work Surface
• Consider the work surface material;
its condition, density, strength,
rigidity and orientation.
WARNING: The vibration emission during
actual use of the power tool can differ from
the declared total value depending on the
ways in which the tool is used. The need
to identify safety measures and to protect
the operator are based on an estimation
of exposure in the actual conditions of use
(taking account of all parts of the operating
cycle, such as the times the tool is switched
off, when it is running idle, in addition
to trigger time).
(1.8) LABELS & SYMBOLS
WARNING: Do not operate this machine
if warning and/or instruction labels are
missing or damaged. Contact Evolution
Power Tools for replacement labels.
Note: All or some of the following symbols
may appear in the manual or on the product.

8
www.evolutionpowertools.com
(1.9) LABELS & SYMBOLS
Symbol Description
VVolts
AAmperes
Hz Hertz
Min-1 Speed
~Alternating Current
noNo Load Speed
Wear Safety Goggles
Wear Ear Protection
Do Not Touch
Wear Dust Protection
Read Instructions
CE certification
Warning
Waste electrical and
electronic equipment
Double Insulated
(1.10) INTENDED USE
OF THIS POWER TOOL
WARNING: This product is a Hand Operated
Compound Mitre Saw and has been designed
to be used with special Evolution blades.
Only use accessories designed for use in
this machine and/or those recommended
specifically by Evolution Power Tools Ltd.
When fitted with an appropriate blade
this machine can be used to cut:
Mild Steel
Aluminium
Wood
(1.11) PROHIBITED USE
OF THIS POWER TOOL
WARNING: This product is a Hand Operated
Compound Mitre Saw and must only be used
as such. It must not be modified in any way,
or used to power any other equipment or
drive any other accessories other than those
mentioned in this Instruction Manual.
(1.13) WARNING: This machine is not
intended for use by persons (including
children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been
given supervision or instruction concerning
the safe use of the machine by a person
responsible for their safety and who
is competent in its safe use.
Children should be supervised to ensure
that they do not have access to, and are
not allowed to play with, this machine.

9
www.evolutionpowertools.com
EN
DE
FR
TR
(1.14) ELECTRICAL SAFETY
This machine is fitted with the correct
moulded plug and mains lead for the
designated market. If the supply cord is
damaged, it must be replaced by a special
cord or assembly available from the
manufacturers or its service agent.
(1.15) OUTDOOR USE
WARNING: For your protection if this
tool is to be used outdoors it should not be
exposed to rain, or used in damp locations.
Do not place the tool on damp surfaces.
Use a clean, dry workbench if available.
For added protection use a residual current
device (R.C.D.) that will interrupt the supply
if the leakage current to earth exceeds 30mA
for 30ms. Always check the operation of the
residual current device (R.C.D.) before using
the machine.
If an extension cable is required it must
be a suitable type for use outdoors and
so labelled. The manufacturers instructions
should be followed when using an
extension cable.
(2.1) POWER TOOL GENERAL SAFETY
INSTRUCTIONS
(These General Power Tool Safety Instructions
are as specified in BS EN 60745-1:2009 &
EN 61029-1:2009)
WARNING: Read all safety warnings and
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/ or serious injury.
Save all warnings and instructions for future
reference. The term “power tool” in the
warnings refers to your mains-operated
(corded) power tool or battery-operated
(cordless) power tool.
(2.2) 1) General Power Tool
Safety Warnings [Work area safety]
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gasses or dust. Power
tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating power tool. Distractions
can cause you to lose control.
(2.3) 2) General Power Tool Safety
Warnings [Electrical Safety]
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
b) Avoid body contact with earthed
or grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat,
oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk
of electric shock.

10
www.evolutionpowertools.com
(2.4) 3) General Power Tool Safety
Warnings [Personal Safety].
a) Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power tool
while you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust masks, non-skid safety
shoes, hard hat or hearing protection used
for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
the power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A wrench
or key left attached to a rotating part of a
power tool may result in personal injury .
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure that these are connected and
properly used. Use of dust collection can
reduce dust-related hazards.
(2.5) 4) General Power Tool Safety
Warnings [Power tool use and care].
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at a rate for which
it was designed.
b) Do not use the power tool if the switch
does not turn it on or off. Any power tool
that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the power tool from the
power source and/or battery pack from the
power tool before making any adjustments,
changing accessories, or storing power
tools. Such preventative safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
Instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of moving parts and any other
condition that may affect the power tools
operation. If damaged, have the power
tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.

11
www.evolutionpowertools.com
EN
DE
FR
TR
(2.6) 5) General Power Tool
Safety Warnings [Service]
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
(2.7) HEALTH ADVICE
WARNING: When using this machine, dust
particles may be produced. In some instances,
depending on the materials you are working
with, this dust can be particularly harmful.
If you suspect that paint on the surface of
material you wish to cut contains lead, seek
professional advice. Lead based paints should
only be removed by a professional and you
should not attempt to remove it yourself.
Once the dust has been deposited on surfaces,
hand to mouth contact can result in the
ingestion of lead.
Exposure to even low levels of lead can
cause irreversible brain and nervous system
damage. The young and unborn children are
particularly vulnerable. You are advised to
consider the risks associated with the materials
you are working with and to reduce the risk
of exposure. As some materials can produce
dust that may be hazardous to your health,
we recommend the use of an approved face
mask with replaceable filters when using
this machine.
You should always:
• Work in a well-ventilated area.
• Work with approved safety equipment,
such as dust masks that are specially
designed to filter microscopic particles.
(2.8) WARNING: the operation of any power
tool can result in foreign objects being thrown
towards your eyes, which could result in severe
eye damage. Before beginning power tool
operation, always wear safety goggles
or safety glasses with side shield or a full
face shield where necessary.
(3.5) ADDITIONAL SAFETY
INSTRUCTIONS - MITRE SAWS
The following specific safety instructions
for Mitre Saws are based on the requirements
of EN61029-2-9:2009.
BLADE SAFETY
WARNING: Rotating Circular Saw Blades are
extremely dangerous and can cause serious
injury and amputation. Always keep fingers
and hands at least 150mm away from the
blade at all times. Never attempt to retrieve
sawn material until the cutting head is in the
raised position, the guard is fully closed and
the saw blade has stopped rotating.
Only use saw blades that are recommended
by the manufacturer and as detailed in
this manual and that comply with the
requirements of EN 847-1.
Do Not use saw blades that are damaged or
deformed as they could shatter and cause
serious injury to the operator or bystanders.
Do Not use saw blades that are manufactured
from high speed steel (HSS).
If the table insert becomes damaged or
worn it must be replaced with an identical
one available from the manufacturer
as detailed in this manual.

12
www.evolutionpowertools.com
(3.6) PERSONAL PROTECTIVE
EQUIPMENT (PPE)
Hearing protection should be worn in order
to reduce the risk of induced hearing loss.
Eye protection should be worn in order to
prevent the possibility of the loss of sight
from ejected chippings.
Respiratory protection is also advised as some
wood and wood type products especially MDF
(Medium Density Fibreboard) can produce
dust that can be hazardous to your health.
We recommend the use of an approved face
mask with replaceable filters when using
this machine in addition to using the dust
extraction facility.
Gloves should be worn when handling blades
or rough material. It is recommended that saw
blades should be carried in a holder wherever
practicable. It is not advisable to wear gloves
when operating the mitre saw.
(3.7) SAFE OPERATION
Always ensure that you have selected the
correct saw blade for the material being cut.
Do Not use this mitre saw to cut materials
other than those specified in this
Instruction Manual.
When transporting a mitre saw ensure that
the cutting head is locked in the 90 degree
down position (if a sliding mitre saw ensure
that the slide bars are locked). Lift the machine
by gripping the outer edges of the base with
both hands (if a sliding mitre saw, transport
using the handles provided). Under no
circumstances shall the machine be lifted
or transported using the retractable guard
or any part of its operating mechanism.
Before each use check the operation
of the retractable guard and its operating
mechanism ensuring that there is no damage,
and that all moving parts operate
smoothly and correctly.
Keep the work bench and floor area clear of all
debris including sawdust, chips and off-cuts.
Always check and ensure that the speed
marked on the saw blade is at least equal to
the no load speed marked on the mitre saw.
Under no circumstances shall a saw blade
be used that is marked with a speed that
is less than the no load speed marked
on the mitre saw.
Where it is necessary to use spacer or reducing
rings these must be suitable for the intended
purpose and only as recommended by the
manufacturer.
If the mitre saw is fitted with a laser it shall not
be replaced with a different type. If the laser
fails to operate it shall be repaired or replaced
by the manufacturer or his authorised agent.
The saw blade shall only be replaced as
detailed in this Instruction Manual.
Never attempt to retrieve off-cuts or any other
part of the work piece until the cutting head is
in the raised position, the guard is fully closed
and the saw blade has stopped rotating.

13
www.evolutionpowertools.com
EN
DE
FR
TR
(3.8) PERFORM CUTS
CORRECTLY & SAFELY
Wherever practicable always secure the work
piece to the saw table using the work clamp
where provided.
Always ensure that before each cut the mitre
saw is mounted in a stable position.
If needed the mitre saw can be mounted
on a wooden base or work bench or attached
to a mitre saw stand as detailed in this
Instruction Manual.
Long work pieces should be supported on
the work supports provided or on appropriate
additional work supports.
(3.4) WARNING: If any parts are missing, do
not operate your machine until the missing
parts are replaced. Failure to follow this rule
could result in serious personal injury.
(3.9) ADDITIONAL SAFETY ADVICE
CARRYING YOUR TABLE MITRE SAW
Safety Advice
• Although compact, this saw is heavy.
To reduce the risk of back injury, get
competent help whenever you have to
lift the saw.
• To reduce the risk of back injury, hold
the tool close to your body when lifting.
Bending your knees so you can lift with
your legs, not your back. Lift by using
the handhold areas at each side of the
machines base.
• Never carry the Table Mitre Saw by the
power cord. Carrying the tool by the power
cord could cause damage to the insulation
or the wire connections resulting in electric
shock or fire.
• Before moving the saw tighten the
mitre and bevel locking screws to guard
against sudden unexpected movement.
• Lock the Cutting Head in its lowest position.
Ensure that the Cutting Head Locking Pin is
completely engaged in its socket.
WARNING: Do not use the blade guard
as a‘lifting point’. The power cord must be
removed from the power supply before
attempting to move the machine.
• Lock the Cutting Head in the down position
using the Cutting Head locking pin.
• Loosen the Mitre Angle Locking Screw. Turn
the table to either of its maximum settings.
• Lock the table in position using the Locking
Screw.
• Use the two carry handle cut-outs
machined into either side of the machine
base, to transport the machine.
Place the saw on a secure stationary work
surface and check the saw over carefully.
Check particularly the operation of all the
machines safety features before attempting to
operate the machine.
(4.1) GETTING STARTED - UNPACKING
Caution: This packaging contains sharp
objects. Take care when unpacking. Remove
the machine, together with the accessories
supplied from the packaging. Check carefully
to ensure that the machine is in good
condition and account for all the accessories
listed in this manual.
Also make sure that all the accessories are
complete. If any parts are found to be missing,
the machine and its accessories should be
returned together in their original packaging
to the retailer. Do not throw the packaging
away; keep it safe throughout the guarantee
period. Dispose of the packaging in an
environmentally responsible manner. Recycle
if possible. Do not let children play with empty
plastic bags due to the risk of suffocation.

14
www.evolutionpowertools.com
(4.2) ITEMS SUPPLIED
Description Quantity
Instruction Manual 1
Hold Down Clamp 1
Push Stick 1
Pin Spanner (Blade Change) 1
Hex Key 6mm
(Blade Change)
1
Hex Key 5mm
(Riving Knife Adjustment)
1
Multi-Purpose Blade (Fitted) 1
Rip Fence/
Bevel Guide Assembly
1
Auxiliary Lower Blade Guard
(Fitted)
1
Dust Bag Adaptor Tube 1
Workpiece Supports 2
Rear Stabilising Arms 2
4.3 ADDITIONAL ACCESSORIES
In addition to the standard items supplied
with this machine the following accessories
are also available from the Evolution online
shop at www.evolutionpowertools.com or
from your local retailer.
(4.4)
Description Part No
FURY Blade FURY210

15
www.evolutionpowertools.com
EN
DE
FR
TR
LH VIEW OF FURY 6 MITRE SAW CONFIGURATION
11
1
12
3
4
2
6
7
5
9
8
10
1. CUTTING HANDLE
2. ROTARY TABLE
3. RETRACTABLE LOWER BLADE GUARD
4. BLADE
5. BEVEL LOCKING LEVER
(Back of the machine)
6. MITRE ANGLE LOCKING SCREW
7. MITRE ANGLE SCALE
8. FENCE
9. HOLD DOWN CLAMP
10. STABILISING ARMS
(X2 Back of machine)
11. CUTTING HEAD RELEASE LEVER
12. TABLE HEIGHT ADJUSTING SCREW

16
www.evolutionpowertools.com
LH VIEW OF FURY 6 TABLE SAW CONFIGURATION
1. ON/OFF TRIGGER SWITCH (Inside handle)
2. ON/OFF LATCHING SWITCHES
3. CUTTING HANDLE
4. TABLE TOP
5. AUXILIARY LOWER BLADE GUARD
6. UPPER BLADE GUARD
7. RIP FENCE
8. PUSH STICK
9. MOUNTING HOLE (2 at the front and
2 under the stabilising arms)
10. CUTTING HEAD LATCHING PIN
(Not shown in this view)
10
7
2
3
1
5
9
8
6
4

17
www.evolutionpowertools.com
EN
DE
FR
TR
GETTING STARTED
WARNING: ALWAYS DISCONNECT THE SAW FROM THE POWER
SOURCE BEFORE MAKING ANY ADJUSTMENTS.
Refer to the“Service Parts Diagram”. Install a blade as detailed in
the“Installing or Removing the Blade”section.
Note: We recommend that the operator reads the ‘Important
Information’ sticker applied to the table of the Fury6. Practicing
and becoming familiar with the procedures outlined on
this sticker will make subsequent adjustments/assembly or
configuring fairly straightforward.
PERMANENTLY MOUNTING THE FURY6 TABLE/MITRE SAW
(Fig. 1)
WARNING: To reduce the risk of injury from unexpected saw
movement, place the saw in the desired location either on a
workbench or other recommended leg set. The base of the saw
has four holes to mount the mitre saw. If the saw is to be used in
one location, permanently fasten it to the workbench or leg set
using appropriate bolts with lock washers and nuts.
Note: When permanently mounting the Fury6 we recommend that
the four (4) rubber feet located underneath each of the mounting
holes are removed and stored safely for possible future use.
1. Tighten the mitre and bevel locks.
2. Position the saw so other people cannot stand behind it.
Thrown debris could injure people in its path.
3. Place the saw on a firm, level surface where there is plenty of
room for handling and properly supporting the workpiece.
4. Support the saw so that the table is level and the saw does
not rock.
5. Bolt or clamp the saw to its support.
For Portable Use (Fig. 2)
Note: The Fury6 is designed to be a highly portable machine.
For portable use the Fury6 must be fitted with
the two (2) rear Stabilising Arms.
Fig. 1
1) Hex headed bolt
2) Spring washer
3) Flat washer
4) Mitre saw base
5) Workbench
6) Flat washer
7) Spring washer
8) Hex nut
9) Lock nut
(1)
(2)
(3)
(4)
(5)
(6)
(7) (8)
(9)
Fig. 2

18
www.evolutionpowertools.com
To fit the Stabilising Arms:
• Remove the cross head machine screws from the two (2) rear
mounting positions.
• Attach the Stabilising Arms with the machine screws, two per
arm and tighten securely.
Note: The Stabilising Arms are fitted with rubber feet. The base
of the Fury6 is also fitted with four (4) identical rubber feet
positioned underneath the mounting holes in the base.
When used as a portable machine the six (6) rubber feet provide
the security and stability necessary for safe operation.
Note: When the machine is re-positioned the operator should
ensure that none of the rubber feet become detached from the
machine. The rubber feet can, in some circumstances, stick to
some surfaces due to vacuum suction.
If any of the rubber feet become detached or damaged they
must be replaced.
DUST BAG
A Dust Bag (not supplied) can be fitted to the extraction port at
the rear of the machine. (Fig. 3a & 3b)
• Push the adaptor tube into the extraction port at the rear of
the machine.
• Slide the Dust Bag onto the adaptor tube ensuring that the
spring clip grips the tube holding the Dust Bag securely in place.
Note: For operational efficiency empty the Dust Bag when it
becomes 2/3 full. Dispose of the contents of the Dust Bag in an
environmentally responsible way. It may be necessary to wear a
dust mask when emptying the Dust Bag
WARNING: DO NOT USE A DUST BAG WHEN CUTTING STEEL.
Fig. 3a
Fig. 3b
(Dust bag, not supplied)
Fig. 4
Fig. 5

19
www.evolutionpowertools.com
EN
DE
FR
TR
TO CONFIGURE THE FURY6
FOR USE AS A MITRE SAW
WARNING: Only carry out this procedure with the machine
disconnected from the power source.
Caution: The Fury6 has many built in safety features and
safety interlocks. It is important that the following instructions,
and those found on the label attached to the machine table
are read, understood and acted upon. Failure to carry out the
configuration procedure could result in damage to the machine
and/or injury to the operator.
• Loosen the table height adjustment screw. (Fig.4)
• Raise the table top to its upmost position and tighten the
height adjustment screw. (Fig. 5)
• Slightly push down on the Cutting Head Handle.
• Pull out the Cutting Head Latching Pin and allow the Cutting
Head to rise to its upmost position. (Fig. 6)
• Remove the Auxiliary Lower Blade Guard and store safely for
future use.
The Fury6 is now ready to use as a Mitre Saw. (Fig. 7)
WORKPIECE SUPPORTS (Fig. 8)
Workpiece supports can be fitted to both sides of the machine
base if required.
• Loosen the relevant Workpiece Retaining Screw located in a
socket at the top front of the machine base.
• Insert the Workpiece Support into the holes machined in the
base.
Note: The Workpiece Support should be pushed ‘fully home’
into the machine base.
Correct installation will require approximately 65mm of the
Workpiece Support to slide into the machine base.
• Fasten the Workpiece Support into the base by tightening
the Retaining Screw.
Workpiece Supports can be very useful in providing extra
support for long workpieces when using the Fury6 in Mitre Saw
configuration.
Fig. 6
Fig. 7
Fig. 8

20
www.evolutionpowertools.com
HOLD DOWN CLAMP (Fig. 9)
A Hold Down clamp is supplied with the Fury6.
Two sockets (one on either side) are incorporated into the rear
of the machines fence.
• Fit the pillar of the clamp into the socket that best suits the
cutting application, ensuring that it is pushed fully down.
• Tighten the fence thumbscrew to lock the pillar of the Hold
Down Clamp into the fence socket.
• Put the workpiece onto the rotary table and against the fence.
• Adjust the Hold Down Clamp so that it securely holds the
workpiece to the rotary table.
• Before attempting any cutting check to ensure that the
clamp does not interfere with the blade path as the Cutting
Head is lowered.
OPERATING INSTRUCTIONS
MITRE SAW CONFIGURATION
WARNING: It is important that the operator is adequately trained
in the use, adjustment and operation of the machine, and has
read the Instruction Manual before commencing operations.
Note: We recommend that when the Fury6 is being used as a
Mitre Saw, the complete Fence Assembly is removed from the
machine as stored safely for future use.
1. Releasing the Cutting Head
Note: When configured in Mitre Saw mode the Cutting Head will
be automatically locked in its upper position with the Retractable
Lower Blade Guard completely covering the blade teeth.
To release the Cutting Head press and hold the Cutting Head
Release Lever.
Gently press down on the Cutting Head Handle to lower the
Cutting Head. The operation of the Retractable Lower Blade
Guard is automatic.
Note: We recommend that when the machine is not in use the
Cutting Head is locked in its down position, with the Auxiliary
Lower Blade Guard correctly installed and the Cutting Head
Latching Pin fully engaged in its socket.
Fig. 9