EXO2 HeatMitt PRO User manual

1
HeatMitt PRO HEATED MITTENS
USER INSTRUCTIONS
WELCOME
Your high performance HeatMitt PRO Heated Mittens, powered by FabRoc™ Heat Technology by EXO2
have been designed to provide warmth and comfort to enhance the safety and enjoyment of your outdoor
activities and can even help to improve blood circulation in your hands and arms.
Our unique FabRoc™ heat technology provides the world’s first self-regulating heating system. No
external controller is required as the FabRoc™ itself will heat to the pre-set temperature of approximately
115-118 degrees Fahrenheit. Continuous use of up to 2.5 hours is available on a single charge of your
small EXO2 3.7 volt PowerPack.
PRODUCT CONTENTS
EXO2 HeatMitt PRO Heated Mittens (Pair)
(2) Miniature PowerPacks (Rechargeable 3.7 Volt Lithium-Ion) - EXO37MR
2-Way Charger Unit - EXO42US2W
FabRoc™

2
SETTING UP AND USING YOUR HEATMITTS
Your HeatMitt PRO Heated Mittens are simple to set-up and use. Each pair comes supplied with individual
3.7 volt, lightweight miniature PowerPacks. (While a trickle charge may exist with each battery when
received, it is strongly recommended that both batteries be fully charged in accordance with the provided
directions before initial use.) Depressing the switch will light the LED to green, which indicates that power
is available and the unit is now on. To operate your HeatMitts, simply insert the mitten 1.3mm plugs into
the charged PowerPacks and then insert them into the integrated pockets.
To charge your HeatMitt PowerPacks, connect them to the supplied charger unit and plug them into a
standard electrical outlet. Please ensure that the PowerPacks are switched on when being charged. The
charger unit LED will light red until charging is complete, at which time the charger LED will change back to
green. The HeatMitt can then be unplugged and used normally. It will take several hours to charge the
PowerPacks fully, however a fast charge, offering several hours of heat, can be achieved after just one
hour of charging. DO NOT LEAVE CHARGING BATTERIES UNATTENDED.
Quick Charging Instructions
Plug-in the Dual Battery Charger to working electrical outlet, ensuring that the Charger LEDs are both
GREEN.
Turn the batteries ON and plug each into the Charger.
The Charger will read the charge level of each Battery individually. (One Charger LED may show green
while it is reading the other Battery.) THIS BATTERY IS NOT YET CHARGED.
Once the first Battery level is read, the second Battery will be read.
Allow the Batteries to remain charged, while in the ON position, for at least 6 hours OR until both
Charger LEDs have remained GREEN for at least 1 hour. The Charger LEDs will remain RED while
charging.
* The Battery LED color (GREEN) will not change.

3
HEATMITT PRO SPECIFICATIONS
1. Quality Soft Leather Palm - For Comfort and Durability
2. FabRoc™ Panels over back of each hand (self-regulating at approximately 115-118°F) to thaw out
frozen hands and fingers (or stop them from freezing in the first place!) - For Soothing Warmth
over many hours use
3. Lycra Shell with Leather Pull Tab - For Stretch Comfort and Long Lasting Durability
4. Hipora breathable & waterproof membrane (front/back) - For Protection and Comfort in all
Weather Conditions
5. Cotton and Polyester Blend Lining - For Comfort and Durability
6. Thinsulate™Insulation - For Heat Retention
7. Drawstring adjuster at gauntlet end - For Maximum Protection in all Weather Conditions
8. Decorative Leather and EXO2 Embroidery Branding
SAFETY FEATURES
DO NOT replace or interfere with the electrical components of your heated mittens, the batteries or
charger unit.
The FabRoc™ heating element installed into your new HeatMitts has been designed for safe and reliable
use. The power system has been tested to comply with US safety regulations and has been CE marked and
UL certified. Safety devices are included to ensure the unit is rendered safe, even under faulty conditions.
Please Note: The HeatMitt PRO Heated Mittens are not designed to be used under water.
TROUBLESHOOTING
What happens if my heated mittens are torn?
DO NOT attempt to replace or interfere with the electrical components in the heated mittens. Return the
item to EXO2 for repair.
What happens if my heated mittens do not get warm?
Confirm that the mittens are properly connected to the supplied PowerPacks and that the LED on the
PowerPacks shows green when switched on (indicating power is available). If they still do not get warm,
contact EXO2 at 877.EXO2.HEAT.
WARRANTY
Every pair of heated mittens is supplied with a one-year warranty covering all electronic and mechanical
failures. In the unlikely event that any part should fail because of a defect within the first year, return it to
us and we will repair or replace it free of charge.
Note: The warranty does not cover intentional alterations, accidental damage or improper cleaning.

4
Should you have any questions about your heated products, please contact:
Consumer Services TEL: 1-877-EXO2-HEAT
EXO2 The Heat Inside, NA, LLC WEB: www.exo2.com
300 Lester Mill Road E-mail: [email protected]
Suite 220
Locust Grove, GA 30248