manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Exor
  6. •
  7. Security Sensor
  8. •
  9. Exor MS1001F Installation and operation manual

Exor MS1001F Installation and operation manual

W4390A
Installation and Commissioning
Instructions
MS1001F / MS1001SM
Bronze Series LightSpot
MS1001SM
MS1001F
Ex-Or
Haydock Lane, Haydock, Merseyside WA11 9UJ
Tel: +44 (0)1942 719229
Fax: +44 (0)1942 272767
Email: technicalsales.ex-or@honeywell.com
www.ex-or.com
At the end of their useful life
the packaging and product
should be disposed of via a
suitable recycling centre.
Do not dispose of with normal
household waste.
Do not burn.
Dimensions
6.0m
2.5m
Technical Data
MAXIMUM RECOMMENDED MOUNTING HEIGHT: 3 metres
RANGE: Cone-shaped detection pattern, diameter (at floor level) = 2.4 x mounting height
OPERATING VOLTAGE: 230V 50Hz (UK & Europe)
RECOMMENDED CIRCUIT PROTECTION: 10 Amps
MAXIMUM LOAD: 6 Amps resistive or fluorescent
2
TERMINAL CAPACITY: 2 x 2.5mm
OFF DELAY: 20 minutes (fixed) and a 10-second Walk Test Mode
DEPTH REQUIRED BEHIND CEILING (for flush version): 62mm from front flange plus an
allowance for the minimum bend radius of the cables
WEIGHT: 200g approx
COLOUR: White
MATERIAL: Flame retardant PC/ABS
IP RATING: 4X
Flange:
10mm deep
100mm 100mm
62mm
Flush Version Surface Version
62mm
deep behind ceiling
Note: HP2000 (or HP10) required for commissioning
Bronze Series LightSpot - MS1001SM & MS1001F
Only suitably qualified personnel should install this equipment.
Fixing
MS1001SM - The housing may be secured to a hard surface or a BESA box. The detector fits into the housing
with a simple bayonet action.
MS1001F - Supplied with a sinking (dry lining) box for flush fitting. Sinking box fits into an 89mm diameter hole in
ceiling tile or plasterboard ceiling. To avoid damage to ceiling tile, do not overtighten. Depth required behind
ceiling: 62mm from front flange plus an allowance for the minimum bend radius of the cable. No access above
the ceiling is necessary.
Note: Do not position within 25cm of a luminaire.
Connection
LOAD
(Max 6 Amps)
N
E
L
Permanent
or switched
supply
N
E
L
Permanent
or switched
supply
Detector
Detector Detector
VOLT-
FREE
OUTPUT
VOLT-
FREE
OUTPUT
VOLT-FREE
OUTPUT
LIVE IN LIVE IN
LIVE IN
NEUTRAL
NEUTRAL NEUTRAL
EARTH
EARTH EARTH
Multiple Detectors
Single Detector
LOAD
(Max 6 Amps)
W4390A
The LIVE IN
terminals are
internally linked
External Link External Link
External Link
Important Additional Notes
1. Only suitably qualified personnel should install this equipment.
2. All terminals on this product are provided for final connections. It is not intended that the product be used as a junction box
for looping cables.
3. Ameans for disconnection must be incorporated in the fixed wiring in accordance with the current wiring regulations.
4. This equipment switches lights no more frequently than would a responsible human occupant. However, manufacturers of
some lighting types (e.g. ‘2D’luminaires) may specify a maximum number of switching cycles and/or a minimum on-time in
order to achieve a predicted lamp life. Please check with the manufacturer of the luminaires to ensure that they are
compatible with automatic controls in this respect.
*
LIVE IN
*
LIVE IN
*
LIVE IN
*
LIVE IN
* *
*
The LIVE IN
terminals are
internally linked
*
Commissioning
The units are supplied with factory default settings (power-up on, fully automatic operation, 20 minute off delay).
Off Delay
The Off Delay is set to 20 minutes and is non-adjustable. A 10-second Off Delay is available for walk testing the
product.
Walk-test Mode
Walk-test mode is used to check that the detector is operating as required. The short off-delay enables the
installer to check that lights are switching on when movements are made at the edge of the detection zone.
1. Change the programmed Off Delay to 10 seconds using either an HP10 or HP2000. When using the HP10,
just press the white button - switch positions are not recognised for this product. When using the HP2000,
select Utilities from the main menu, then select Walk Test and press OK.
2. Move around the area that is being controlled, stopping for 10 seconds to allow the lights to switch off, before
moving and triggering the lights back on. The Off Delay will reset to its 20 minutes after a five minute period.

This manual suits for next models

1

Other Exor Security Sensor manuals

Exor MLS CONNECT MLS2000CDR Installation and operation manual

Exor

Exor MLS CONNECT MLS2000CDR Installation and operation manual

Exor MLS2000PF Installation and operation manual

Exor

Exor MLS2000PF Installation and operation manual

Exor LS1000R User manual

Exor

Exor LS1000R User manual

Exor LR15 Installation and operation manual

Exor

Exor LR15 Installation and operation manual

Popular Security Sensor manuals by other brands

Buckeye X Series user manual

Buckeye

Buckeye X Series user manual

Zipato vs-zp3102+.eu Quick installation guide

Zipato

Zipato vs-zp3102+.eu Quick installation guide

Vanderbilt AGB800-AM Instruction and installation manual

Vanderbilt

Vanderbilt AGB800-AM Instruction and installation manual

MSA altair 5 Quick start card

MSA

MSA altair 5 Quick start card

Well SENS-PIR-C02-WL user manual

Well

Well SENS-PIR-C02-WL user manual

SENSECAP S2106 user guide

SENSECAP

SENSECAP S2106 user guide

UNICONTROL Electronic S-SW-8 Resumed Manual

UNICONTROL Electronic

UNICONTROL Electronic S-SW-8 Resumed Manual

Schaller Automation VISATRON VN93 Series Maintenance procedures

Schaller Automation

Schaller Automation VISATRON VN93 Series Maintenance procedures

Iget SECURITY EP1 quick start guide

Iget

Iget SECURITY EP1 quick start guide

B.E.G. LUXOMAT PD3-1C Installation and operating instruction

B.E.G.

B.E.G. LUXOMAT PD3-1C Installation and operating instruction

SICK KTX Prime manual

SICK

SICK KTX Prime manual

Edimax AI-2003W Quick installation guide

Edimax

Edimax AI-2003W Quick installation guide

PCB Piezotronics 4204-03A Installation and operating manual

PCB Piezotronics

PCB Piezotronics 4204-03A Installation and operating manual

Mircom MIX-2351TAP Installation and maintenance instructions

Mircom

Mircom MIX-2351TAP Installation and maintenance instructions

Agilent Technologies G3485A installation instructions

Agilent Technologies

Agilent Technologies G3485A installation instructions

Dalsa RAD-ICON 2329 user manual

Dalsa

Dalsa RAD-ICON 2329 user manual

ABB Busch-Wachter Presents 6131-74-101-500 user manual

ABB

ABB Busch-Wachter Presents 6131-74-101-500 user manual

Atom AT4105 instruction manual

Atom

Atom AT4105 instruction manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.