PACK CONTENTS
REQUIRED
MOUNTING/ INSTALLATION STEPS
x1 x1 x1 x1 x1 x1
x1x1 x1 x1 x2
M4 x 14mm
(For Euro conduit box
installation)
M3 x 20mm
(For ceiling mout
installation)
Hole saw size:
Ф75mm - 80mm
M3 x 15mm
(For cable clamps
installation)
x2
x4
Surface Mount
1
4
2
5
3
6
7
9
8
I
5mm
4mm
No 2
Phillips
3mm
0FF
230V
ij
5mm
50.8mm or 60mm
60mm
50.8mm
CAUTION:
OR
OR
‘CLICK’ ‘CLICK’ ‘CLICK’
Switch OFF the electricity at the fuse box by
removing the relevant fuse or switching off the circuit
breaker before proceeding with the installation.
IMPORTANT
L1L2LN
Wiring diagram
Connect the mains supply
cable to the terminal block on
the backplate as follows.
Connect the cable from the
lighting load to the terminal block
on the backplate as follows.
Note: Remove the external link
between L and L2
( See connection diagram )
Option1
Connection:
L
N
Live Brown
L1 Switched Live White
Neutral Blue
Earth Green / Yellow
L
N
Live Brown
L1 &
L2
Relay contact
for external load White
Neutral Blue
Earth Green / Yellow
The device needs
20-50 seconds to
warm up.
x2 x2
1 x 2.5mm²
Cable entry
capability at
terminal block
2 x 1.0mm²
2 x 1.5mm²
Cut out
here
N
NL
μ
L2 L1
L
Option2
* Remark: L1 & L2 is relay output N
NL
L2 L1
L
L1
L2
μ
LS1000R LightSpot 360° Dual Mount PIR installation and operating instructions
Only suitably qualified personnel should install this equipment
!!
Haydock Lane
Haydock
Merseyside
WA11 9UJ
UK
www.ex-or.com
Technical Support
+44 (0)1942 719229
WALK TESTING
1 3
Activate Manual Override Operation
MANUAL OVERRIDE OPERATION
SWITCHABLE LOAD
TECHNICAL SPECIFICATIONS
Detection Range:
Detection Angle:
Power Supply:
Maximum Switchable Load:
Time On Adjustment:
Dusk Level Adjustment:
Operating temperature:
Environment Protection:
Up to 6 metres diameter (3m Radius)
at mounting height of 2.5m
360°
220 ~ 240 VAC / 50 Hz
Max load current 6A
Incandescent / Halogen Max 2000W
Flourescent lamp (magnetic) Max 500W
Flourescent lamp (electronic ballast) Max 400W
Low energy (CFL) Max 120W
LED lamp Max 110W
Fan Max 75W
5 seconds - 15 minutes
Day & night or night only operation
-20 to 40°C
For ceiling mount - IP44
For flush mount - IP44 (at sensor portion only)
- IP20 (ceiling board onwards)
Max 400W
Max 500W
Max 2000W Max 120W
Max 110W
Max 75W
2
MIN. SUN.
warm up
20-50 SEC
Around
10 second
Lamp turn on
when reach Lux
setting level.
ON
OFF
ON
2 times within 2 seconds
DUSK
DAWN
Hrs
2 SEC
5
SEC
1
Deactivate Manual Override Operation
Manual deactivation before dawn
2Auto deactivation when
dusk to dawn ON
Lamp turn off when
dusk to dawn.
OFF
ON
1 time within 1 second
1 SEC
5
SEC
OR
Auto Mode
Auto Mode
ON
