EXPERT GRILL XG1910200103 Installation guide

Vendor Stock NO.: XG1910200103
24-INCH HEAVY-DUTY CHARCOAL GRILL
ASSEMBLY INSTRUCTION MANUAL
FOR OUTDOOR USE ONLY.
PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY
RETAIN THIS MANUA FOR FUTURE REFERENCE.
If you have any or problems, you can our customer
service at from 8:00am to
4:30pm eastern , Monday through Friday for assistance.
DO NOT RETURN TO THE PLACE OF PURCHASE.

10
Parts List with graphic
No. Descripon Part Image QTY Part#
1 ※Temperature
Gauge 1pc 17221701
2 ※Lid Decorave
Plate 1pc 17221702
3 Hood Assembly 1pc 17221703
4 Upper Hood
Hinge 2pcs 17221704
5 Warming Rack 1pc 17221705
6 Cooking Grid 2pcs 17221706
7 Lower Hood
Hinge 2pcs 17221707
8 Fire Box Back
Panel 1pc 17221708
9 Fire Box Le
Panel 1pc 17221709
10 LeShaSupport
Bracket 1 pc 17221710

11
No.DescriptionPartImageQTYPart#
11
FireBoxFront
Panelwith
charcoaldoor
(pre‐assembled)
1pc17221711
12ButterflyDamper4pcs17221712
13※Butterfly
DamperHandle4pcs17221713
14AshPan1pc17221714
15※AshPan
DecorativePlate1pc17221715
16※LargePipePlug4pcs17221716
17LeftBackLeg1pc17221717
18LeftFrontLeg1pc17221718
19CartHandle1pc17221719
20LegEndCap2pcs17221720

12
No. Part Image QTY Part#
21 Hood Handle 1pc 17221721
22 Spacers 4pcs 17221722
23 Charcoal Tray 1pc 17221723
24 Assembly 1pc 17221724
25 Right Sha
Support Bracket 1pc 17221725
26 Fire Box Right
Panel 1pc 17221726
27 ※Handle Locking
Bracket 1pc 17221727
28 Crank Handle 1pc 17221728
29 ※Handle Grip 2pcs 17221729
30 Side Shelf 1pc 17221730

13
No. Descripon Part Image QTY Part#
31 Door Locking
Lever 1pc 17221731
32 Trim 1pc 17221732
33 Charcoal Door
Handle 1pc 17221733
34 Ash Pan Handle 1pc 17221734
35 Bole Opener 1pc 17221735
36 Right Front Leg 1pc 17221736
37 Right Back Leg 1pc 17221737
38 Wheel 2pcs 17221738
39 Axle 1pc 17221739
40 Boom Shelf 1pc 17221740
※：NO ASSEMBLY REQUIRED

14
HARDWAREKIT
ASSEMBLYPREPARATION
Beforebeginningassemblyofproduct,makesureallpartsarepresent.Inspectcontentsofboxto
makesureallpartsareincludedandnotdamaged.Ifanypartismissingordamaged,donot
attempttoassembletheproduct.
NOTE:Somepartscomewithscrewspre‐installed.Loosenandtightenforfinalassembly.
EstimatedAssemblyTime:1hourbytwopeople
Toolsrequiredforassembly:
*PhillipsHeadScrewdriver1pc(notincluded);
*Wrench 1pc(notincluded)
*Plier 1pc(notincluded)
No.DescriptionPartImageQTY
AM6x12mmScrew22pcs
BM6x35mmScrew8pcs
CM6ShoulderScrew4pcs
DM10Nut1pc
EHingePin2pcs
FCotterPin2pcs

15
ASSEMBLYINSTRUCTIONS
IMPORTANT:ASSEMBLEONFLATANDSOFTSURFACETOAVOIDSCRATCHING.
1. Loosenpre‐assembledScrewsandleavethescrewheadsprotrudingapproximately1/5 inch.
Hangthesidepanelsontothescrewsandtightenthemasshown.
2. PutLegEndCap(20)intoLeftBackLeg(17)andLeftFrontLeg(18).
MakesuretheLegEndCapislockedintothesquareholeonthelegs.
26
9
8
11
17
18
20

16
3. Use8pcsAscrewstoattachlegstoeachcorneroftheFireboxasshown.

4. Use4pcsAScrewstoattachtheBottomShelf(40)tothe4Legs.
.

40
A
37
A
17
18
36
AM6X12mmScrewX 4
AM6X12mmScrewX 8

17
5. Thread Axle (39) through the Wheels (38), Right LeLeg and Right Back Leg, and then fasten
D Nut as shown.
6. Remove the pre-assembled Self-Tapping Bolt from the p of Crank Handle and loosen the
handle from the bracket.
Use 2pcs A Screws to aach the Right Sha Support Bracket (25) together with Handle Locking
Bracket (27) from inside of Firebox front panel.
Note: Retain the removed Self-Tapping Bolt for use in next step.
D M10 NUT X 1
A M6X12 mm Screw X 2
D
39
38
A
Self-Tapping Bolt
28
25 27

18
7. Rotate the Crank Handle (28) into the hole of the front panel and then fasten the Self-Tapping
Bolt to the end of the Crank Handle (28).
Note: Make sure to rotate the crank handle counterclockwise completely to the end.
Self-Tapping Bolt
28