2
MPA 152 Plus • Setup Guide (Cont’d)
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2013 Extron Electronics All rights reserved. www.extron.com 68‑1320‑52
Rev A 06 13
The MPA 152 Plus sums and weights the left unbalanced signals from the TRS and RCA receptacles. This summed,
unbalanced signal is then summed with the left balanced signal from the captive screw receptacle. The right channel is
handled in the same way.
The left and right channels are then sent to the output ampliers in one of two ways, depending on how the
front panel switch is set (see the diagram to the right).
zStereo: The left and right channels are sent to the left and right output amplifers respectively.
zDual Mono: The left and right channels are summed and then the resulting mono signal is fed to both of
the output ampliers.
NOTE: The captive screw, RCA and TRS inputs are buffered.
5. Connect the pre‑wired captive screw connector to one of the 2‑pole,
3.5 mm captive screw outlets on the provided power supply and the
other end into the power receptacle on the amplier (see the gure
to the right). The power cord connectors are correctly wired when
shipped. The MPA152 Plus ships with a 24 W desktop power supply.
ATTENTION:
• See the attention notices in the Power Input section of the
MPA152 Plus Series User Guide for important information
about using power supplies.
• When the power supply is connected to the MPA152Plus, it
must not be shared with any other devices.
6. Adjust the MPA 152 Plus input level, bass, and treble from the front panel (see gure at right).
a. If necessary, unplug the remote connector from the unit (see step 7, below).
b. If connecting the amplier to a system with adjustable volume, set the system volume
to its lowest point. Then adjust the MPA152 Plus front panel level potentiometer fully
counterclockwise.
c. Set the system volume to its maximum volume level (no sound should come out).
d. Return to the MPA 152 Plus and raise the level until sound distortion rst occurs, then lower slightly until the distortion
disappears. This setting ensures that, whatever the system volume setting may be, no clipping occurs.
e. Adjust bass and treble to preference.
7. The rear panel 3‑pole Remote captive screw port on the amplier can be used for remote control of the
volume by an Extron volume controller such as an Extron VCM100 AAP, VC 50, or MLA VC10 Plus. A
MediaLink controller can also adjust the audio volume via a network connection or by IR remote (see the
MPA 152 Plus Series User Guide).
Power
Receptacle
DC Power Cord
Captive Screw
Connector
MPA 152 Plus
Amplifier
DC Power
Outputs
DO NOT USE
AC Power Cord
Tie
Wrap
Captive Scre
Connector
Power Supply
Output Cord
PS 1220
Power Supply
POWER
12V
0.7A MAX
VCG
10V50mA
REMOTE
BASSLEVEL TREBLE
MINI POWER AMPLIFIER
MPA 152 PLUS
DUAL
MONO
