Extron electronics Cable Cubby F55 Edge User manual

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the
product specifications.
Cable Cubby F55 Edge • Installation Guide
The Extron Cable Cubby F55 Edge is an edge-mount cable
access enclosure that integrates AV technology and power on
the furniture surface. It is designed for congurable rooms that
require semi-permanent AV connectivity, control, and power.
An integrated clamp system secures the enclosure to the
furniture without requiring tools or cutting.
This guide provides instructions for an experienced installer to
install and connect the Extron Cable Cubby F55 Edge Cable
Access Enclosure.
Kit Contents
Flex55 Adapter Module (2)
Grommet
Plugs (8)
Zip Ties (4)
Pry Tool (2)
Cable Grommet
Plate (2)
Cable Cubby F55 Edge
Figure 1. Cable Cubby F55 Edge Kit Contents
Planning
Read the following information before installing the Cable Cubby F55 Edge.
Check with Local and State Regulations Before Starting the Installation:
• Ensure that the planned installation complies with building and electrical codes.
• Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check All Parts and Equipment Before Installation:
• Ensure that all parts are present in each kit.
• Ensure that necessary tools and equipment are available for the installation.
NOTE: Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact
or entanglement (see Routing and Connecting Cables on page9).
VOLUME
DISPLAY
PC VIDEO
OFF
ON
MUTE
LAPTOP
VOLUME
DISPLAY
PC VIDEO
MUTE
LAPTOP
OFF
ON
USB CHARGER
120V 50-60Hz 6A MAX
~
1
ZipClip 100 ZipClip 200 ZipClip 400
PMK 155
Optional Accessories

Cable Cubby F55 Edge • Installation Guide (Continued)
2
Application Diagram
The application diagram below shows a power, data, and video wiring setup from a laptop to a conference monitor. The setup is
made simple by using the included Cable Cubby Flex55 Captive Cable Kit, installed in the Cable Cubby F55 Edge enclosure.
Q4 Sales by Region
Northwest
Northeast
Southwest
Southeast
Central
Q4 Sales by Region
Northwest
Northeast
Southwest
Southeast
Central
DISPLAY
OFF
ON
VOLUME
PC VIDEO
MUTE
LAPTOP
E
USB CHARGER 120V 50-60 Hz 6A MAX
~
Power HDMI
Extron
Cable Cubby F55 Edge
Edge Mount Cable Access
Enclosure for AV Connectivity,
Control, and Power
Figure 2. Application Example Using the Cable Cubby F55 Edge Enclosure
2

3
Preparing the Cable Cubby F55 Edge
The Cable Cubby F55 Edge enclosure supports Flex55 and EU modules, which can be installed in a variety of combinations (see
the example in gure3). These modules can be installed either before or after the Cable Cubby F55 Edge installation. Optional
Retractor modules can be installed with the appropriate brackets, sold separately. Detailed retractor installation instructions are
available with the Retractor bracket kit and in the Cable Cubby F55 Edge Retractor Module Setup Guide at www.extron.com.
VOLUME
DISPLAY
PC VIDEO
OFF
ON
MUTE
LAPTOP
VOLUME
DISPLAY
PC VIDEO
MUTE
LAPTOP
OFF
ON
USB CHARGER
120V 50-60Hz 6A MAX
~
Figure 3. Cable Cubby F55 Edge with Control, Power, and Cable Pass-through Modules
NOTE: For a complete and up-to-date list of compatible modules, see the product page at www.extron.com.
3

4
Cable Cubby F55 Edge • Installation Guide (Continued)
Installing Modules into the Cable Cubby F55 Edge
The following illustration shows the process for installing the double-size Flex55 AC+USB 130 US Power Module into the Cable
Cubby F55 Edge enclosure. Note that half- and full-size modules can be snapped into the enclosure without removing the
supports (1). Retractor modules also can be installed, in any slot in the enclosure (see the Cable Cubby F55 Edge Retractor
Setup Guide, available at www.extron.com, for more information).
1
Extron Cable Cubby
F55 Edge Enclosure
Plan and prepare the enclosure for
module installation.
For a double-size module installation,
use pliers to carefully twist the desired
bridge support back and forth until loose,
and remove.
NOTE: Removal of a bridge
support is irreversible.
Figure 4. Removing a Module Support for Double-sized Flex55 Installation
Snap the grommet plate
into the Adapter Module.
b
b
b
Snap included grommet plugs
into any unused holes in the
grommet plate.
c
2
2
2Install the cable grommet plate for cable pass-through applications.
For cable pass-through installation,
insert the cables through the bottom
of the Cable Cubby F55 Adapter Module
and through the holes of the gr
ommet plate.
a
a
a
Figure 5. Installing the Cables
4
5

5
Attach additional
devices here.
Extron Cable Cubby
Flex55 Edge Enclosure
E
xtron Cable Cubby
F
lex55 Edge Enclosur
e
Extron
Flex55 AC+USB 130 US
Insert the module into
the Cable Cubby.
Connect to
power source.
USB CHARGER
120V 50-60Hz 6A MAX
~
3
3
3
3
3
3
3
Figure 6. Installing the Flex55 AC+USB 130 US into the Cable Cubby F55 Edge Enclosure
6

6
Cable Cubby F55 Edge • Installation Guide (Continued)
Attaching an Optional ZipClip Mounting Device to the Cable Cubby F55 Edge
The ZipClip 100, 200, or 400 can be attached to the Cable Cubby F55 Edge in order to mount a power supply or other device to
the Cable Cubby. Determine which ZipClip to use (depending on the device being attached) and in which orientation (vertical or
horizontal). Note that the ZipClip 400 can be mounted horizontally only. Plan and ensure that there is ample space for the device
and its cables.
UP
21-XYZ-01LF
21-XYZ-01LF
UP
ZipClip 100 — Vertical Mounting ZipClip 100 — Horizontal Mounting
ZipClip 200 —
Vertical Mounting ZipClip 200 — Horizontal Mounting
ZipClip 400 — Horizontal Mounting
Figure 7. Mounting ZipClips
7

7
Attaching an Optional PMK 155 Mounting Kit
Follow these steps to attach a PMK 155 Mounting Kit to the Cable Cubby F55 Edge.
1. The Cable Cubby F55 Edge is delivered with an accessory mounting bracket attached. Detach this bracket by removing its
two mounting screws (see figure8). Set the bracket and screws aside. You will reattach them in step 3.
Accessory Bracket
Figure 8. Removing the Accessory Mounting Bracket from the Cable Cubby F55 Edge
2. Attach the PMK 155 to the accessory bracket using the two screws and washers from the PMK kit (see figure9).
Figure 9. Attaching the PMK 155 to the Accessory Bracket
8
9
Cable Cubby F55 Edge • Installation Guide (Continued)

8
Cable Cubby F55 Edge • Installation Guide (Continued)
3. Attach the accessory bracket and PMK 155 to the Cable Cubby F55 Edge, using the two screws removed in step 1.
Figure 10. Attaching the PMK 155 and Accessory Bracket to the Cable Cubby F55 Edge
Mounting the Cable Cubby F55 Edge to a Table
Mount the Cable Cubby F55 Edge on the edge of the table as shown below.
Under the table, turn both thumbscrew clamps
and tighten them snugly to secure the enclosure.
Ensure the Cable Cubby F55 Edge is firmly secured
to the furniture.
Hold the assembled
Cable Cubby F55 Edge
enclosure onto the edge
of the table.
1
2
Figure 11. Mounting the Cable Cubby F55 Edge to a Table
10
11

9
Routing and Connecting Cables
Organize and connect cables as shown in gure12. Use zip ties (provided) to fasten the cables to the enclosure where needed.
DISPLAY
OFF
ON
VOLUME
PC VIDEO
MUTE
LAPTOP
E
USB CHARGER 120V 50-60Hz 6A MAX
~
Zip tie locations on th
e
inside of the clamps
Figure 12. Routing and Managing the Cables
12

10
Cable Cubby F55 Edge • Installation Guide (Continued)
Appendix — Removing Modules from the Cable Cubby F55 Edge
If the modules need to be replaced or removed from the Cable Cubby F55 Edge enclosure, the following diagrams show the procedure
for removing modules with the provided pry tool. This process applies to any compatible Flex55 and EU module.
NOTE: To verify the location of the locking tabs, check the module specifications (available at www.extron.com).
4
Unhook the other locking tabs, if applicable,
and remove the module.
HDMI
USB CHARGER
120V 50-60Hz 6A MAX
~
VOLUME
DISPLAY
PC VIDEO
OFF
ON
MUTE
LAPTOP
VOLUME
DISPLAY
PC VIDEO
MUTE
LAPTOP
OFF
ON
Insert pry tool
at the locking
tab location.
T
wo pry tools may
need to be used
simultaneously for
lar
ger modules to
unhook.
1
Locking
Tab
USB CHARGER
120V 50-60Hz 6A MAX
~
USB CHARGER
Pull the pry tool away from
the module to unhook each
locking tab from the
mounting frame.
2
Repeat steps 1 and 2 to
unhook the locking tabs
on the other side of the module.
3
To verify the location of the locking tabs,
check the module specications.
Figure 13. Removing Modules
13

11
Installation Overview
• Planning (see page 2)
• Check with local and state regulations before starting the installation.
• Check all parts and equipment before installation.
• Preparing the Cable Cubby F55 Edge (see page 3)
• Check the modules for compatibility and installation requirements.
• Installing Modules into the Cable Cubby F55 Edge (see page4)
• Install half-, single-, and double-size modules into the Cable Cubby F55 Edge.
• Remove any bridge supports if necessary. Note that removal of bridge supports is irreversible.
• (Optional) Installing Retractor Modules (see the Cable Cubby F55 Edge Retractor Guide, provided with
the Cable Cubby F55 Edge Retractor Bracket Kit)
• Install Retractor modules in the Cable Cubby F55 Edge.
• (Optional) Attaching a ZipClip (see page 6)or PMK 155 (see page 7)to the Cable Cubby F55 Edge
• If using a ZipClip, determine which model to use (100, 200, or 400), and in which orientation (vertical or horizontal). Plan
and ensure there is ample space for the device and its cables.
or
If using a PMK 155, remove the accessory bracket from the Cable Cubby F55 Edge and attach the bracket to the
PMK 155. Re-install the accessory bracket with the PMK to the Cable Cubby F55 Edge.
• Attach the ZipClip or PMK 155 to the Cable Cubby F55 Edge.
• Attach the desired power supply or other device to the ZipClip or PMK 155.
• Mounting the Cable Cubby F55 Edge (see page 8)
• Clamp and secure the Cable Cubby F55 Edge to the edge of the table.
• Routing and Connecting Cables (see page9)
• Organize and connect the cables.
• Use tie wraps to attach cables to the enclosure where needed.

12
68-3569-50 Rev. A
12 22
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2022 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876