Extron electronics ISM Series Quick start guide

ISM MTP UT 4DA Output Board Installation Notes
The Extron ISM MTP UT 4DA is a twisted pair transmitter board for the ISM 824 with four RJ-45
outputs, two RS-232 inserts, and local audio output.
The board mounts in one of the four vertical expansion
slots (numbered 1 to 4) at the rear of the ISM 824.
For full operating details of the ISM refer to the
ISM 824 User’s Manual, online at www.extron.com.
To install an output board in the ISM 824 base unit,
1. Turn off the ISM 824, and remove the power cord.
Repeat for all connected devices.
2. At the rear, select an open slot, or take out the
blank plate from the desired output port by
removing the two retaining screws (top and
bottom), and lifting the blank away.
NRe-use the screws to secure the new output
board in place. Retain the blank plates.
If a board is already installed in the desired slot,
remove the screws and carefully pull out the
board.
3. Remove the board from its outer box and anti-ESD
bag, holding the boards by the rear frame.
4. With the board upright, align the front (non connector end) of the board with the top and
bottom plastic guides in the ISM 824. Slide the board in carefully, keeping within the guides.
Push it home firmly, and secure it with the retained screws.
5. If applicable, repeat steps 2through 4for any other output boards.
6. Power on the ISM 824. The new output board(s) is auto-detected, and takes approximately
30 seconds to initialize. The LCD display indicates the new board type,
slot used, and counts down the initialization time. See inset for example
display for a new ISM MTP UT 4DA board installed in Slot #3.
7. Using suitable twisted pair cables connect any MTP
receiver, DA, or switcher to the RJ-45 twisted pair outputs
on the installed boards. See wiring details at right.
NUse the same standard at both ends of the twisted pair
cable.
8. Insert a 5-pole captive screw connector from an audio
device into the local audio output connector for balanced
or unbalanced stereo audio. Wire the connector as shown
below.
Balanced Stereo Output
Tip
Ring
Sleeve(s)
Tip
Ring
L R
Left
Right
Unbalanced Stereo Output
Tip
NO GROUND HERE.
Sleeve(s)
Tip
NO GROUND HERE.
L R
Left
Right
CAUTION
For unbalanced audio, connect the sleeve(s)
to the center contact ground. DO NOT connect
the sleeve(s) to the negative (-) contacts.
.
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
NOTE If you are using Enhanced
Skew-Free™ A/V cable, use the
TIA/EIA T568A standard only.
(Continued on reverse side)
100
-
240
50/60 Hz
1.2A MAX.
1
2 3 4 5 6 7 8
2 1 2
345 678
12
1
INPUTS OUTPUTS
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
PASS THRU
INPUTS
RESET
LAN
REMOTE
RS232/RS422 ACT LINK
OUTPUT
VIDEO
SCALER
70-545-01
3
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
UNIV.
SCALER
70-544-01
5
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
PASS
THRU
70-547-01
8
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
Extron
ISM 824
Integration Scaling
Matrix Switcher
Align output board with
top and bottom plastic guides.
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
7
SCAN
CONV.
70-546-01
Example Output Board Installation
New ISM MTP UT 4DA
Slot #3 18
INSERT 3/4
LOCAL
AUDIO OUTPUT
LR
1234
BUFFERED OUTPUTS
RS 232
Tx Rx
INSERT 1/2
Tx Rx
ISM
MTP UT 4DA

Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
68-1123-60
Rev A
02 09
ISM MTP UT 4DA Output Board Installation Notes, cont’d
9. Connect a control device to RS-232 insert 1/2 (for
outputs 1 and 2), or insert 3/4 (for outputs 3 and
4). This allows bidirectional, pass-through control
signals to and from the control device and the
MTP devices on ports 1 and 3, and unidirectional
pass-through signals from the control device on
ports 2 and 4. Ports 1 and 2 always receive the
same RS-232 command signal, but only port 1
allows for bidirectional communications. The
same is true for ports 3 and 4, where port 3 allows
for bidirectional communications (see right).
See below for board specific SIS™commands.
ISM MTP UT 4DA configuration menu
Using the front panel menu buttons (Menu and Next), the
ISM MTP UT 4DA board configuration menu can be accessed.
From the Output Configuration screen, press Next until reaching
the #xISM MTP menu (see the image at right). Using the front
panel adjustment knobs ({ [), change the settings as desired.
Power up input and output devices and create the desired ties.
Board specific SIS commands table
Alternatively, the ISM MTP UT 4DA board can be configured with specific SIS commands.
NX! = ISM 824 output number, 3,5,7,8 (i.e. the slot/port occupied by the ISM MTP UT 4DA)
X@ = RS-232 number 0 = insert 1/2, 1= insert 3/4
X# = Setting value 0 = off, 1= on
X$ = Sub-output number (setting for each MTP output on each card) 1,2,3,4
Command ASCII
command
(host to switcher)
Response
(switcher to host)
Additional description
Local RS-232 ports
Enable EX!*X@*1LRPT X!LrptX@*1]Enable RS-232 insert X@ to
control output X!.
Disable EX!*X@*0LRPT X!LrptX@*0]Disable RS-232 insert X@
controlling output X!.
View EX!*X@LRPT X#] View the RS-232 status X# for
output X!.
Output Pre-peaking
Turn on EX!*X$*1OPEK X!OpekX$*1]Turn pre-peaking on for output
X! to MTP sub-output X$.
Turn off EX!*X$*0OPEK X!OpekX$*0]Turn pre-peaking off for output
X! to MTP sub-output X$.
View
status
EX!*X$OPEK X#]View the pre-peaking status X#
for output X!.
RS-232 Insert 3/4
<Off> On
Next
Output Card
Configuration
Next
Prepeaking #x
<Off> On
RS-232 Insert 1/2
<Off> On
Select Ouptut
#xISM MTP UT 4DA
Next
Next
RS-232 Commands
RS-232 Commands
INSERT 3/4
L
OC
AL
AU
DI
O
OU
TP
U
T
L
R
1234
BUFFERED OUTPUTS
RS 232
Tx Rx
INSERT 1/2
Tx Rx
I
SM
M
TP UT 4D
A
Bidirectional
1234
BUFFERED OUTPUTS
Unidirectional
Tr ansmit (Tx)
Receive (Rx)
Ground (Gnd, )
© 2009 Extron Electronics. All rights reserved.