Extron electronics UPB 125 User manual

1
UPB 125 • Installation Guide
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before starting installation.
When using this projector mount, always follow basic precautions, including the following:
CAUTION: Risk of Personal Injury. Maximum projector weight for the UPB 125 is 40 lbs (18.1 kg).
ATTENTION : Risque de blessure grave. Le poids maximum du projecteur pour le UPB125 est 18,1kg (40lbs).
SAVE THESE INSTRUCTIONS
NOTE: Refer to local building standards and codes to verify that the installation will meet the regulatory requirements.
Observe all local and national building and safety codes, UL requirements, and ADA accessibility guidelines.
The UPB 125 is a versatile projector mount that works with most
projectors weighing up to 40 pounds (18.1 kg) and accepts a
1.5 inch -11.5 NPT/NPS pipe.
The exibility of the UPB 125 allows for quick dismounting and
remounting of the projector to the support pipe.
The UPB 125 consists of two parts: the upper Pipe Adapter
Block A, which mounts onto the projector pipe, and the lower
Base Plate Assembly Bwhich attaches directly to the projector
(see image at right).
For product specications visit www.extron.com.
PROPER MOUNTING PROCEDURES
MUST BE FOLLOWED.
Before Starting the Installation:
Check the Projector
cWeight — The UPB 125 can mount a projector with a maximum weight of 40 pounds (18.1 kg).
cMounting points — Use all available mounting points (typically three or four) on the projector base to securely attach the
projector.
cCheck the minimum and maximum throw distance of the projector. See the projector documentation for details.
cCheck the projector lens offset. See the projector documentation for details.
Check the Mounting Location
cCheck the structural ceiling to ensure that it can support a load four times the total weight of the final setup.
UPB 125 Included Parts
Item Part Qty.
APipe Adapter Block 1
BBase Plate Assembly 1
CArms, arm securing screws (M5x10 mm)
and washers, projector mounting barrels
4 each
DMounting screws (M4x8 mm,
M5x12 mm, M6x12 mm)
4 each
ELock screw (M5x10 mm) 1 each
A
B
C
Base Plate
AssemblyPipe Adapter
Block
A
B

UPB 125 • Installation Guide (Continued)
2
Pipe Adapter
Block
Base Plate
Assembly
Arm Locking
Screw and
Washer
Barrel
Arm
Projector
Mounting
Screw
Loosen the thumbscrew and slide
the Pipe Adapter Block A away
from the Base Plate Assembly B.
A
B
D
C
Pivot arms towards center of the projector.
ATTENTION: Center the Arm Barrel
on the mounting point.
Mounting Point on the Projector Base
Insert and tighten down
an appropriate sized screw.
Installing the UPB 125
Preparation
Separate the two main parts (Pipe Adapter Block Aand Base
Plate Assembly B) of the UPB 125 (see the gure at right).
Installing the Base Plate Assembly on the Projector
1. Invert the projector on a protected surface to access the
mounting points.
2. At the end of the arm C,rotate the barrel so that it
protrudes from the base of the arm about 1/4 inch.
3. Select the correct sized projector mounting screws D
that fit the projector mounting point inserts.
4. Attach the arms to the projector (see the figure at right).
5. Pivot the arms so that they extend towards the center of the
projector (see the figure at right).
It is critical to provide evenly level arms at each mounting
point for the Base Plate Assembly to secure to.
ATTENTION:
• Do not overlap the arms.
• Ne pas superposer les pattes de montage.
6. With the arrow on the Base Plate Assembly pointing towards the front
of the projector, place the Base Plate Assembly on top of the arms
and adjust for slot alignment with the holes in the arms.
7. Loosely secure each arm to the base plate (see the figure at right).
8. As close as possible, balance the weight of the projector evenly
across the Base Plate Assembly. Adjust the Plate on the arms as needed.
ATTENTION:
• Distribute the projector weight evenly on the arms.
• Répartissez le poids du projecteur de façon égale sur les
pattes.
Lift the assembly at opposite corners to assess if the conguration
is approximately balanced.
Align a screw hole with a slot
in the Base Plate Assembly.
Then place washer, insert the screw,
and tighten down the screw.

3
9. Check for stress on the arms. To do this, loosen the mounting screws.
(do not remove). If the arm or the barrel lifts, this indicates stress on the
arm. Adjust the height of the threaded barrels to reduce or eliminate
any torque or stress that might be caused by crossed arms or by projector
mounting points with differing heights. It is important to keep the arms
level and as close (low) to the projector base as possible.
Check that the projector weight is still as evenly distributed as possible.
Hand tighten all the screws until snug.
ATTENTION:
• Do not overtighten the mounting screws as this may damage
the projector.
• Ne serrez pas trop les vis de montage au risque
d’endommager le projecteur.
Attaching the Base Plate Assembly to the Pipe Adapter Block
1. Loosen the two set screws (M5) on the Projector Pipe Block and screw the
Block onto the bottom of the pipe (see the figure at right). A minimum
of three turns are needed to safely secure the bracket on the pipe.
2. Swing open (down) the cable harness and thread through any cables
exiting from the projector pipe (see images at lower right).
Close the cable harness. This keeps the cables out of the way when
attaching the Base Plate Assembly to the Pipe Adapter Block.
3. Carefully lift the projector up to the Projector Pipe Block and, with the
projector facing forward, slide the Base Plate Assembly onto the Projector
Pipe Block (see the image below). Tighten down the thumbscrew.
4. On the side opposite the thumb screw, insert and tighten down the
additional lock screw E.
INCORRECT— Arm not level
Causes stress on mounting points
Lock Screw E
Front
Cable Harness
Set Screws (2)
Thumb Screw
CORRECT— Arm level
No stress on mounting points
Projector
Mounting
Pipe
Route cabling.
Close harness.
To open cable harness,
pull harness out and swing
it down.

4
UPB 125 • Installation Guide (Continued)
© 2014-2019 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
68-2171-01 Rev. B
08 19
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
Adjusting the Projector Alignment
Adjust the rotation (yaw)
Turn the unit on the projector pole to the correct position.
Secure the position by tightening the two set screws against the pole.
ATTENTION:
• Do not turn the unit all the way to the end of the pole or the
projector may fall.
• Ne pas tourner l’unité complètement à l’extrêmité du pôle
au risque de faire tomber le projecteur.
Adjust the vertical angle (pitch) and horizontal tilt (roll)
1. On the Base Plate Assembly, loosen the vertical angle and
horizontal tilt adjustment screws.
2. Adjust the vertical angle (pitch) of the projector to the correct
alignment. Tighten down the two vertical angle adjustment
screws.
3. Adjust the horizontal tilt (roll) of the projector to the correct
alignment. Tighten down the two horizontal tilt adjustment
screws.
Vertical Angle
Adjustment
Screws (2)
Horizontal
Tilt Adjustment
Screws (2)
Pitch (Vertical Angle)
bRoll (HorizontalTilt)
c
Ya w (Rotation)
Installation Checklist
Planning (page 1)
Check the projector:
Weight
Mounting point locations
Minimum and maximum throw distance of the projector
Check the mounting location, in particular the structural ceiling loading.
Check the local building standards and codes.
Check the Americans with Disabilities Act or other accessibility requirements.
Installation (pages 2 and 3)
Separate the Pipe Adapter Block from the Base Plate Assembly.
Adjust the barrels on the arms, center on the mounting points, and secure the arms onto the projector.
Place the Base Plate Assembly onto the arms, adjust, and secure.
Adjust the assembly for weight distribution and torque reduction, and tighten down all the screws.
Install and secure the Pipe Adapter Block on the pipe.
Attach the Base Plate Assembly with the projector onto the Pipe Adapter Block and secure.
Finishing the installation (page 4)
Adjust the yaw, pitch, and roll.