Extron electronics MTP 1500RL 15HD A SEQ User manual

IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
MTP 1500RL 15HD RS SEQ • Setup Guide
This guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL
15HD RS SEQ twisted pair receiver.
For full details, see the MTP 1500RL 15HD RS SEQ User Guide, available online at www.extron.com.
INPUT BUFFERED OUTPUT
POWER
12V
1.0A MAX
MTP 1500RL 15HD RS SEQ
MTP
RS-232
RxTx
OUTPUT
MTP
ON
H + V + CSYNC
SOG VIDEO END BI-232
MTP 1500RL SERIES
RGB
PEAKING
LEVEL
DELAY
RED
GREEN
BLUE
SELECT
ADJUST MIN/MAX
MTP
MTP
Installation and Setup
Step 1 — Mounting
Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD RS SEQ receiver as required.
Step 2 — Connect Input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD RS SEQ receiver.
Terminate the cable as shown below right, using the same standard (T568A or T568B) at both ends.
Input
Source
MTP Tx
Device Display
MTP RL Rx
Device
Input
Source
MTP Tx
Device MTP 1500RL
15HD RS Device Display
Transmission distance with one device before the MTP 1500RL 15HD RS SEQ
Transmission distance with more than one device before the MTP 1500RL 15HD RS SEQ
VGA
cable
VGA
cable
TP
cable
1000 feet (305 m) maximum
(RS-232 data signals)
MTP 1500RL
15HD RS Device
VGA
cable
VGA
cable
TP
cable
TP
cable
1500 feet (457 m) maximum (video signals)
1500 feet (457 m) maximum (video signals)
1000 feet (305 m) maximum
(RS-232 data signals)
NOTE: The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free™AV cable terminated in accordance
with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable. Using preterminated and tested cables is also
recommended. Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications.
Step 3 — Connect Outputs
Attach the applicable output cables (video, audio, and buffered output).
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected RS-232
Device Pins MTP Reciever
Pins
A. High resolution video output — Connect a suitable display device to the 15-pin HD
connector (RGB).
B. RS-232 connector —Connect an RS-232 compatible MTP transmitter to the 3-pole
captive screw connector (wired as shown at right) for bi-directional or uni-directional
communication up to 1,000 feet, (305 meters) maximum.
C. Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.
Step 4 — Receiver DIP Switches
• H sync (H+) and V sync (V+) switches — Set these switches up (On) for positive sync or
down (Off) for negative sync.
• Composite Sync, SOG, and Video switches — Set these switches as shown in the table
(see right) to output the indicated format.
• End Unit switch — Set this switch up if either of the following is true:
• The receiver being congured is the only receiver connected to the transmitter.
• The receiver being congured is the last receiver in a daisy-chained system.
• BI-232 switch — Set this up (ON) for bi-directional or down for uni-directional communication.
Pin T568A Wire
Color
T568B Wire
Color
1 White-green White-orange
2 Green Orange
3 White-orange White-green
4 Blue Blue
5 White-blue White-blue
6 Orange Green
7 White-brown White-brown
8 Brown Brown
Insert Twisted
Pair Wires
Pins:
RJ-45 Connector
12345678
Output
Format C Sync SOG Video
RGBHV
RGBS
RGsB
Component*
S-video*
Composite*
* Input video format must match.
ON
H + V + CSYNC
SOG VIDEO END BI-232

MTP 1500RL 15HD RS SEQ • Setup Guide (Continued)
Extron USA Headquarters +1.800.633.9876 (USA/Canada Only) Extron USA - West: +1.714.491.1500 FAX: [phone] Extron USA - East: +1.919.850.1000 FAX: [phone]
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Step 5 — Power
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
AA
Tie
Wrap
POWER
12V
xA MAX Rear
Panel
Ridges
Earth
Ground
3/16"
(5 mm)
Max.
Wire the 2-pole captive screw connectors for the included external 12 VDC power supplies (see
image a on the right). Plug them into all units.
Grounding guidelines
Extron MTP 1500RL 15HD RS SEQ products can be adversely affected by electrostatic discharge (ESD)
if they are not grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an Extron
MTP 1500RL 15HD RS SEQ product in either of two ways:
• Ground the power input port — Insert one end of the grounding wire to the negative or ground pin
on the power input connector (see image aon the right). Tie the other end of the wire to an earth
ground.
• Ground the chassis — Use a connector hex nut (see image bon the right). Tie the other end of
the wire to an earth ground.
If you have any questions about how to ground a product in a specic application, contact an Extron technical
support specialist.
Step 6 — Peaking and Level
Adjust the image sharpness using the Peaking control. Increased peaking compensates for mid- and high-frequency
RGB
PEAKING
LEVEL
MIN/MAX
detail loss. The LED lights red when minimum (zero) or maximum peaking is reached.
Adjust the image brightness using the Level control. View the image and adjust either control for the best image quality.
Step 7 — Skew Compensation
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have
built-in skew compensation capabilities. Adjust the equalization as follows:
A. Set the skew delay to zero for red, green, and blue by using a Tweeker or small screwdriver to press and hold
DELAY
RED
GREEN
BLUE
SELECT
ADJUST
the Select button for 3 seconds. When the Red, Green, and Blue LEDs all go out, release the Select button.
B. Use UTP cable test equipment or examine the displayed image to determine which video signal — red, green,
or blue — is shifted furthest to the right.
C. Adjust the furthest left video signal by using a Tweeker or screwdriver to press and release the Select button until
the LED for the left-shifted color lights.
D. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
E. Repeat steps C and D to align the third color if needed.
68-1555-50
Rev. C
01 13
Figure 1. Example of a Typical MTP 1500RL 15HD RS SEQ Application
INPUT
Tx Rx
RS-232
MONITOR
POWER
12V
.5AMAX
OUTPUT
CABLE
NORM LONG
MTP TVG A RS
POWER
12V
1.0AMAX
RS-232
Rx
Tx
OUTPUT
INPUT BUFFEREDOUTPUT
MTP1500RL 15HD RS SEQ
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
ON
MTP
MTP
POWER
12V
1.0AMAX
RS-232
Rx
Tx
OUTPUT
INPUT BUFFEREDOUTPUT
MTP1500RL 15HD RS SEQ
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
ON
MTP
MTP
PC
Flat Panel
Display
Flat Panel
Display
Extron
MTP 1500RL 15HD RS SEQ
Twisted Pair Receiver
with Loop-Through and Skew EQ
500' (152 m) UTP Cable
(CAT 5/5e/6)
Extron
MTP T 15HD RS
Twisted Pair
Transmitter
RS-232
RS-232
RGBHV
RGBHV
500' (152 m) UTP Cable
(CAT 5/5e/6)
RS-232
RGBHV
Extron
MTP 1500RL 15HD RS SEQ
Twisted Pair Receiver
with Loop-Through and Skew EQ
Maximum transmission distances:
Data (RS-232) 1000' (305 m)
Video 15 00' (457 m)
b
a