Eyecon EC2150 Crossfire User manual

Model eC2150

2
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
IteMs RequIRed foR staRtup ....................................................................3
CaMeRa dIagRaMs.................................................................................... 4-5
BatteRy InstallatIon.................................................................................6
MeMoRy CaRd InstallatIon......................................................................7
quICk setup....................................................................................................8
advanCed settIngs & funCtIons............................................................8
MountIng & fIeld setup...........................................................................11
Red laseR ......................................................................................................13
CaMeRa CaRe ...............................................................................................13
tRouBleshootIng......................................................................................15
WaRRanty InfoRMatIon ..........................................................................16
pRoduCt RegIstRatIon CaRd ..................................................................18
WARNING! Prolonged exposure from looking directly into any infrared light could
cause cataracts or permanent retinal damage. Do not look directly into the camera
during test mode! Failure to follow this warning may cause serious injury or blindness!
WARNING! Do not expose camera interior components, batteries, or SD card to
rain or water. Make sure camera and hands are completely dry before handling. Failure
to follow this warning may result in serious damage to the camera and/or its parts,
personal electrical shock or death!
WARNING! Only batteries as designated in this manual should be used. Failure to
follow this warning may result in leaking batteries, serious damage to the camera, and
personal injury or death!
July 2015. Published by Premier Outdoor Equipment, LLC, Windom, Minnesota.
© 2015 Premier Outdoor Equipment, LLC All rights reserved.

3
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
IteMs RequIRed foR staRtup:
• 10-AACellAlkalineBatteries (Sold separately)
• 1-SDHCStorageCard(upto32GB) (Sold separately)
NOTE:Eyecon™TrailCameras can accept SD cards up to 32GB, but testing shows
that maximum performance is obtained at 16GB.
• 1-ExternalSDmemorycardreader for viewing photos/videos.
(Sold separately)
• optIonal:1 Model ECA100Extenda-Life rechargeablelithiumbattery
pack. (Sold separately)
note: The CRossfIRe “Patent Pending” design has a dual power supply.
The camera will operate using 10-AA sizealkalinebatteries or the eCa100
Extenda-Life battery pack, or a combination of both. If both alkaline and
the Extenda-lifepack are used together, the camera will run on the external
Extenda-lifepack until depleted and then automatically switch to the internal
alkalineAAbatteries. It will always run on the external pack rst when both
battery sources are installed in the camera.
To see which battery source the camera is using, look at the batteryindicator. If
there is an lon the Right Side of the batteryindicator this means the camera
is running on the ECA100Extenda-LifeLithiumpack. If a Chas replaced the l
this means the camera has switched over to the internal alkalineAAbatteries
and you should remove the Extenda-Lifepack for recharging.

4
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
*This opening must be keep free from dust or dirt and should never be covered.
Ambient
Light Sensor* Camera Head
Locking Screw
Red Laser
Light
Dual Locking
Tab
Bark
Biter
Bark
Biter
CAUTION
LASER RADIATION
DO NOT STARE
INTO BEAM

5
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
DualLockingTab
Unlocked
Dual Locked
Lock Case
Door Only
SD Card
Slot
Plus
Arrow
Minus
Arrow
Set
Button
Power On/O
Button
AA Battery
Compartment
Bottom of camera

6
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
BatteRy InstallatIon:
If usIng aa - Cell BatteRIes
1. To remove the internal AA battery pack, slide the locking tab located on the bottom
of the camera back towards the bark biters. Next, pull down and slide the battery
pack until it is removed from the camera housing.
2. Reference the battery icons located near the top of the AA battery compartment.
Insert the batteries accordingly as indicated by the positive and negative battery
icons.
3. Slide the battery compartment back up into the camera housing and press the slide
lock forward until it is completely engaged in the slot in the bottom the housing.
Note: Installing any of the 10-AA batteries in the wrong direction may cause the
batteries to leak acid and could possibly explode, causing camera failure and damage
to the battery compartment. Check your battery indicator after brand new batteries are
installed, it should register full bars. If not you may have a battery in backwards.
If usIng eyeCon™extenda-lIfe BatteRy paCk
1. Remove plastic plug on the back side of the camera. note: Save this plug for future
use. It should alWays be in position when the Extenda-LifeBattery Pack is not
being used.
2. Insert Extenda-LifeBatteryPack(at the bottom of the housing) by sliding it into
position until it “clicks”into place.

7
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
MeMoRy CaRd InstallatIon:
to Install the sd CaRd (Sold separately)
1. To access the user interface and insert a SD card, lift up on the front of the locking
latch located on top of the camera head. After the latch is disengaged, the camera
head should pivot down freely. note: if the camera head does NOT pivot or move
freely, loosen the tension adjusting screw located on the right side of the camera. Do
not force the camera head. If it does not move freely, you must loosen the adjusting
screw.
2. Insert the SDHCcard with the logo of the SD card manufacturer facing out or away
from the LCD screen. The SDHC card should slide in freely with little resistance.
Continue pressing the card down until
you hear a click. This means the SD card is
locked in place and ready for use. Press it
once to remove.
note: We do not recommend using
cards that came out of a camera from a
dierent CameraManufacturer or one
that has previously been used in a Point
&Shoot camera. If you have, make sure to
do a full format on a PC, a Quick format
will not remove les or information, or resolve problems. Your CROSSFIRE might not
be able to accept or read the SD card properly. Always format even brand new SDHC
cards; a full format is again recommended.
photo sIZe
(Resolution)
MeMoRy CaRd sIZe
= nuMBeR of photos
4gB 8gB 16gB 32gB
1.3 Mp 8000 16000 32000 64000
3.0 Mp 3619 7238 14476 28952
5.0 Mp 2381 4762 9524 19048
7.0 Mp 1604 3208 6416 12832
9.0 Mp 1032 2064 4128 8256
Video(30Sec) 433 866 1733 3466

8
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
quICk setup:
Your CRossfIRe will come with the following standard options already preset so that
quality photos may be taken right out of the box without changing any settings.
Mode: Photo BuRst: 3 photo-burst
ResolutIon: 3mp delay: 10 sec
If you wish to customize
your own settings
proceed to Advanced
Settings&Functions.
Camera
Options
Column
Battery
Indicator
Arrow
Indicates
Selection
UserSetupScreen
advanCed settIngs & funCtIons:
Press and release the powerbuttonontheright to activate the camera and view the
usersetupscreen.
Setting the functions is easy; simply use the +or –arrows to select the feature (blinking)
you wish to change and then push the SETbutton. Each feature will blink and can be
changed using the +/–arrows and then push set to move to the next feature.
CloCk: This will set the Time,Date and Year that will be stamped onto the bottom
of your photos.

9
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
To set the tIMe: Use either the +or –arrows and scroll up until the “Clock” starts to
ash. Press the SETbutton and Clock will stop ashing, and either “AM” or “PM” will
start to ash. Use the arrows to select the correct setting and press the SETbutton to
move on to the “Hour” setting. Use the +or –arrows again to set the correct Hour,
press the SETbutton and move on to get the “Minutes” to ash. Arrow up or down the
correct Minutes and hit set to nish setting the time. This will bring you back to the
cameraoptionscolumn, where you’ll notice the “Clock” is ashing again.
To set the Month: Use the +or –arrows and scroll down until the “Date” starts to
ash. Press the setbutton and you will see “MM” start to ash. Pressing the setbutton
again will allow you to select the correct Month. Use the +or –arrows to change the
Month setting.
To set the day: Press the setbutton again and you will see “DD” start to ash. Pressing
the setbutton again will allow you to select the correct Day. Use the +or –arrows to
change the Daysetting.
To set the yeaR: Press the setbutton again and you will see “YY”start to ash. Pressing
the setbutton again will allow you to select the correct Year. Use the +or –arrows to
change the Year setting.Press the setbutton again and this will bring you back to the
cameraoptionscolumn and you will notice the “Date” is ashing again.
photo: This option will show you how many photos and/or videos the camera has
taken.
To check photos: Use the +or –arrow to scroll down to “Photos”
Mode: Mode selects whether you would like the camera to take still photos or take
video clips. Options are: Photo (still) or Video.

10
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
To set the Mode: Scroll down by pressing either the +or –arrows until the “Mode”
starts to ash. Press the setbutton until an arrow starts to ash by either Photo or
Video, this determines what Modethe camera is in. Press the +or –arrows to select
either the Photo or Video setting. Press the setbutton again to lock in the setting and
exit Mode. You will see “Mode” ashing again in the cameraoptioncolumn.
BuRst: Burst selects how many photo images you would like the camera to take in a
row before set trigger delay kicks in. Options are: 1,3,or5.
To set the BuRst: Use the +or –arrows to scroll down until the “Burst” starts to ash.
Press the setbutton until an arrow ashes at one of the Burstsettings. Use the +or
– buttons to select the desired Burst setting. Press the set button again to lock in
that setting and exit Burst. You will see “Burst” ashing again in the cameraoptions
column.
vId lg: This setting selects the length you would like each video to be. Options are: 10
seconds,30secondsor1 min.
To set the vIdeo length: Use the +or –arrows to scroll down until the “VideoLG”
starts to ash. Press the setbutton until an arrow ashes at one of the Video settings.
Use the +or –arrows to select the desired Video lg setting. Press the setbutton again
to lock in that the setting and exit VideoLG. You will see “VideoLG” ashing in the
cameraoptionscolumn.
Res: This setting selects the resolution at which you would like the camera to take the
pictures. A higher resolution photo requires more storage. Options are: 3MP,5MP,or
7Mp.
To set the ResolutIon: Use the +or –arrows to scroll down until the “Res” starts to
ash. Press the setbutton until an arrow ashes at one of the Res settings. Use the +

11
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
or –arrows to select the desired Res setting. Press the setbutton again to lock in that
setting and exit Res. You will see “Res” ashing again in the cameraoptionscolumn.
delay: This setting selects the trigger delay at which you want to run your camera.
This is the amount of time between each burst. Options are: 10seconds,30seconds,
1minuteor5minutes.
To set the delay: Use the +or –arrows to scroll down until “Delay” starts to ash. Press
the setbutton until an arrow ashes at one of the Delay settings. Use the +or –arrows
to select the desired Delay setting. Press the setbutton again to lock in that setting
and exit Delay. You will see “Delay” ashing again in the cameraoptionscolumn.
MountIng & fIeld setup
The CRossfIRe comes with a 6 ft nylon mounting strap which allows for quick and
easy mounting. The camera back is unique in that it has 12 vertical large bark biters
and several dierent adjustment slots. This allows for several strap placement options
or another strap can be added depending on your application. Either way, you can be
guaranteed that the CRossfIRe will mount to just about anything.
The “Patent Pending” CRossfIRe design is very unique; the camera head has the
ability to pivot up and down without the aid of any other mounting apparatus. No
more wedging sticks between the camera and the tree to get the correct camera angle,
especially on those crooked and twisted tree.
• To tilt and release the head simply loosen the spring-loaded tension screw located
on the right side of the camera head.
• Note: make sure the locking screw located on the bottom right side of the camera
head is released before you try to pivot the head. Loosen the locking screw by

12
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
turning it out or counter clockwise until the camera head moves freely.
• Using the LaserLight, pivot the camera head until the desired location or target
area is reached. Next, turn the locking screw clockwise to tighten the camera head in
place. Caution: Light pressure from the locking screw is sucient to hold the camera
head in place; do not over tighten the locking screw.
• Another big advantage of the CRossfIRe is to elevate the camera 10-20 ft o the
ground. It will be less conspicuous to game, other hunters or camera thieves; it will
also be better protected from animals, such as a curious bear.
a. If you choose not to elevate the camera as earlier suggested the ideal mounting
height for deer or big game should be waist high or around 36 to 40 inches from the
ground. For shorter game like bear or turkeys, knee height will work better.
b. The motion detection angle of your CRossfIRe is about 60 degrees, which is slightly
wider than the camera Field of View. The motion detection distance in ideal conditions
is 50–70 ft. This can be greatly aected by weather conditions, animal body size, and
speed at which an animal passes through the detection zone.
aRMIng the CaMeRa: There are two dierent ways your
CRossfIRe can be armed. To start the automatic arm process, do not touch any of the
setup buttons for 15 seconds. Next, the screen will display and start a 15 second count
down. When the countdown is complete, the camera will be self armed. It can also be
force armed by pressing the +and –arrows at the same time until the screen goes
blank.
To wake the camera up, simply touch the power button. Do not hold the button down
or the camera will shut o. Note: If the camera is in the process of taking still photos or
videos, it must rst complete the process before it will wake up.

13
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
Red laseR: The redlaserlightorwalktestlighton your CRossfIRe is
used to help determine your camera is set at the proper height and is pointed in the
right direction. This laser is extremely helpful for camera setups that are mounted up
higher where the camera head needs to be pointed down towards the target. After 90
seconds the red laser will shut o and remain o. Unlikeconventionalwalktestlights
thatashonwhenmotionisdetected,thislasersystemwillshutowhenmotion
isdetectedandthenturnbackonaftertheobjectpassesthroughthedetection
zone.
Note: your camera does not wait to start taking pictures until after the
redlaserlightshuts o.For example, if you have the delay set to 10
seconds, it will record pictures within 10 seconds from when the screen
goes blank and the camera is armed.
CautIon: Do not stare directly into the laser light. Prolonged
exposure may cause permanent eye damage.
CaMeRa CaRe
Moisture,vibration,and extremetemperature can cause severe damage to your trail
camera and should be avoided. Keeping your camera free from moisture and vibration
and using in the correct temperatures will assure you many years of maintenance free
service and operation.
MoIstuRe: Although all Eyecon™ Trail Cameras have a very durable plastic
composite case which also makes them water resistant even under the most extreme
weather conditions, care must be taken to prevent water damage.
• neveR mount your trail camera upside down or leave the case open for an extended
period of time.
CAUTION
LASER RADIATION
DO NOT STARE
INTO BEAM

14
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
• neveR change batteries, camera settings or SD cards in heavy rain.
•If your camera would happen to get water inside, remove the batteries immediately and
allow the camera to dry out for several days before activating it.
vIBRatIon: Like any electronic device, your Eyecon™ Trail Camera is
designed with many small electronic components that are very sensitive to vibration.
Failure to follow careful handling & transport may cause extreme and irreparable
damage to your camera.
• neveR drop the camera on a hard surface
• alWays transport your camera in a method to avoid bouncing around or vibration.
teMpeRatuRe:
Recommended storage and operating temperature: -10° F to 120° F.
note: Battery life and functions may discontinue or experience shortness in extreme
cold/warm
• neveR store your camera in a vehicle or other contained environment with extremely
high temperatures for an extended period of time!
Note: The CRossfIRe is designed with a low battery voltage shut down to ensure
maximum camera performance. For example, if your camera was in use for several
weeks or months and you push the power button to wake it up, you may notice a
ashing “BatteryWarning”in the area were the date and time normally are. The
only way to clear the battery warning is to remove and replace the batteries. It is
highly recommended not to use the camera until the batteries have been replaced.

15
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
tRouBleshootIng
CaMeRa not RespondIng: If your camera at anytime does not respond when the
buttons are pushed or you cannot turn it o, your camera maybe locked up. The best
way to resolve this problem is to remove the AA battery compartment for a period of
10 seconds. This will cut the main power supply to the camera and will take care of the
problem. If you are using both the external ECA100Extenda-LifelithiumBatteryPack
and internal aa Alkaline supply, you will need to do the same for both.
Bad sdhC CaRd: Over time a sdhC or any storagedevice could become corrupt. If your
camera fails to acknowledge the SDHCcard we recommend that you replace the card with
a new SDHCcard or one from a dierent EYECON™Trail Camera that you know works.
This will help determine whether the problem is the SDHCcard or the camera. We do not
recommend using cards that have been used in cameras from dierent manufactures and/
or dierent styles of cameras unless a FullFormat on a PC is done to those cards.
note: If you used a poInt & shoot camera to view your pictures and videos on the
SD card, this may cause problems when reinserted back into your CRossfIRe. It is
recommended to do a FullFormat on a PC before it goes back in to the camera.
IMage qualIty: Your CROSSFIRETrailCamera is designed to give you optimum trigger
speed along with great night photo clarity. There may be some instances where an animal
is moving extremely fast or light conditions may be insucient, causing a smearing/blurry
object within your image. This is a natural part of photo taking and may occur from time
to time.
FirmwareUpdates: To ensure maximum performance and reliability from your camera
periodically check our website for the most current rmware updates and installation for
your camera at www.eyecontrailcameras.com.

16
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
WaRRanty and RegIstRatIon
EyeconTrailCamera’s1Year LimitedWarranty: For a period of 365 days
after purchase, Eyecon Trail Cameras will, at its discretion, repair or replace this
product for any reason of any defect or malfunction. This warranty is only valid
if the product is used for the purpose intended and has not been tampered
with and/or physically damaged in any way. Products that have been damaged
due to negligence or misuse do not qualify for warranty replacement.
to aCtIvate WaRRanty:
• You MUSTregisteryourCROSSFIREEyeconTrailCamera within30days
of purchase to receive any warranty protection!
• You MUST keep a copy of your receipt as Proof of Purchase for any
warranty protection!
to oBtaIn a WaRRanty ClaIM:
1. You Must call our customer service department at 844-745-7723 or 507-
832-8322 and follow all troubleshooting requests rst.
2. If Warranty Claim is approved, a RANumber will be given to you; keep this
for your records.
3. RemoveyourSDcardandbatteries(any items other than original camera
casing will be destroyed and not returned with new item)

17
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
4. Includeacopyofyouroriginalreceipt,yourRA#,andacheckorcredit
cardnumberfor$20.00shipping/handlinginthebox.
5. Shiptheboxprepaidto: Eyecon Trail Cameras, Camera Returns, 1905 1st
Ave. N., Windom, MN 56101. MakesuretoputtheRA#inboldletterson
 theoutsideofthebox.

18
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
To activate your product’s warranty, please mail in your registration
card or submit it online at www.EyeconTrailCameras.com
pRoduCt RegIstRatIon
Product Purchased
Model Number
Serial Number
Owner’s Name
Street Address
City State Zip Code
E-mail Address Phone
Owners Age (optional) Sex (optional) M F
Date Purchased
Purchased From (Dealer Name)
How did you hear about us: Catalog Webpage Friend
Magazine Other, Please Explain
Are you a: Bow Hunter Gun Hunter Both
Treestand Preference: Fixed Position Climbing Ladderstand

19
PLEASE REGISTER TO ACTIVATE YOUR PRODUCT’S WARRANTY.
OWNER’SRECORD
Product Name
Model Number
Serial Number
Purchased From
Purchased Date
you Must RetuRn the CoMpleted RegIstRatIon CaRd aBove
WITHIN(30)DAYSOFTHEPURCHASEINORDERTOACTIVATETHELIMITED
WaRRanty CoveRage. (Make sure to include date purchased on the card!)
notes:
Remembertoactivateyourproduct’swarranty?
See warranty information and registration
instructions on page 16 and then complete and
mail in the registration card on page 18
or submit it online at:
www.EyeconTrailCameras.com

PO Box 454 • Windom, MN 56101
844-745-7723 • 507-832-8322