EZ-ACCESS SUITCASE User manual

10266 REV 05-06-15
Instructions
SUITCASE®Singlefold AS Ramp
Optional Top Lip Extension is available. Contact your local EZ-ACCESS retailer for details.
RATED LOAD
Maximum weight limit is 800 pounds.
INSTALLATION
1. Read and follow all instructions before use.
2. Do not use if ramp is damaged or unstable.
3. For wheelchairs and scooters only (not intended for
commercial use).
4. Ramp is shipped fully assembled. To separate ramp into two
halves for easy stowage and transportation, remove bolts and
install hinge pins as follows:
a. Position as shown in (FIGURE 1). Align hinges, then insert
hinge pin into each hinge assembly and connect ramp
sections together before use. Spring section of pin should
be on the underside (non-treaded side) of ramp.
Ramp may be separated for use when loading or
unloading unoccupied mobility equipment only.
When used with occupied mobility equipment, use
ramp as one unit (ensure both halves are joined with
hinge pins or bolts firmly installed before use).
5. Place ramp on landing in the folded position, making sure that
the top lip transition plate (labeled TOP) is resting securely on
the landing, see FIGURE 2.
6. Unfold ramp and center on landing.
7. For ease in carrying and stowage, ramp can be disconnected
and carried in two sections. (When hinge pins are not in use,
store in one side of hinge or on the underside of ramp by
inserting into the gap behind the top I-beam.).
SAFETY & MAINTENANCE
Regularly check ramp for damage, and check and tighten any loose
fasteners. Keep ramp surface clear of ice, snow, dirt, leaves, and
other debris. For snow/ice, remove accumulation and sweep the
surface clean. To remove dirt, leaves, and other debris, sweeping
the surface or using a garden hose will usually suffice, but, if
needed, use a damp cloth or soft brush with non-alkaloid detergent
and water. Rinse well and use extra caution if ramp surface is wet.
WARNING!
Ensure top lip transition plate is secure before using ramp.
We recommend attaching ramp temporarily to the landing
using provided clevis pins (drill ¼” hole in landing) or semi-
permanently using screws through pre-drilled holes at the top
of each section. To prevent ramp from becoming dislodged
during use, make sure that the top lip transition plate overlaps
the resting surface as far as possible.
The surface holding the top lip transition plate needs to be
substantial and of sound construction.
Ramp may be slippery when wet or icy.
Use ramp only with a qualified helper and always use lap belt.
The ramp shown in the figures below is the 5-ft length. To
select the ramp length, an incline chart is provided on the
reverse side of this document. However, it is intended only as
a guideline. Refer to your equipment's (wheelchair or scooter)
Owner Guide for the proper degree of incline/decline and
chair direction before attempting ramp use. Never exceed its
recommendations.
OPTIONAL ACCESSORY
Increase the usefulness of the SUITCASE®Singlefold AS ramp with
the Top Lip Extension (TLE). This optional extension increases the
standard 3” top lip
transition plate to
become 9”,
allowing the ramp
to clear the rear
bumper of SUVs
and vans by
simply attaching to
the top lip of the
ramp. TLE is for
use with
unoccupied
mobility equipment
only and, when used, reduces the overall ramp weight capacity to
500 pounds
FIGURE 1 FIGURE 2 FIGURE 3

10266 REV 05-06-15
INCLINE CHART
IMPORTANT: Refer to your
equipment's (wheelchair or
scooter) Owner Guide for the
proper degree of incline/decline
and chair direction before
attempting ramp use. Never
exceed its recommendations.
TO ESTABLISH THE PROPER RAMP LENGTH:
Determine the incline that your chair is designed to climb.
Measure the rise (distance from the top step, porch, van, etc.
to the ground).
Refer to Incline Chart to find proper ramp length.
At any incline, use ramp only with a qualified helper.